I just started a Christmas Tree Repair business and your video was just what I needed to see. Now I can finish pulling out burnt out lights an putting in new ones only 900 light to change. (Green Holiday Tree Lighting Company) Interior Christmas Tree replacing lights and stripping of lights.
I fix 10-12 sets each year, either from dead bulbs or busted wires. Speaking of moisture protection, are you concerned about the led keeper puncturing all those tiny holes in the wires? Its definitely crossed my mind since I've seen many times what a wire puncture can do to car wiring. That's my go to method for wire repairs except I use the pink connectors and a dedicated crimping tool, far better than that crimper in those strippers.
Hey there, Scott. I'm not worried about the puncture. The plastic is meant to self-heal. I asked that question to a light company and to Ulta-Lit last year and to they said the same thing. So, after fixing lights on a few strings, I went back and looked at the wire and couldn't find that holes a day or two later.
This will make a great gift package for my uncle. He hangs lights like you do and always complains about broken lights. Thanks so much for the gift idea and the links!!🎁🎄👍
Thank you for this and for the product links! I went to put lights up but something got to them and chewed through several wires and I can't remember where I bought them to color match the rest. So, I need to fix them and this video saves the day!
Sometimes, you might need a magnifying glass or use your phone and zoom in. But one of the wires will have tiny white writing on it, which makes it the positive wire. One wire will be positive, one will be a negative wire, and the 3rd wire will have the lights attached to it.
@@ChristmasOnCrestline thanks! i just came inside from doing this project. all went well except the heat gun singed a bit of the existing wire coating. probably ran it too hot. didn't look like copper wire was exposed but wrapped it in electrical tape. think that will be fine?
Does this work for both incandescent and led. The light keep tool says you must have a resistor like in the pod when you remove a socket and connect the wires together
No, this only works for LED strings. They mention the rectifier as only LED strings have those. For in candescent lights we have to use the LIght Keeper Pro. Here are two videos showing this tool: ua-cam.com/video/4vYBVp4m9dY/v-deo.htmlsi=WHQp44LVjg0jm5zd ua-cam.com/video/tV0FepnwZuc/v-deo.htmlsi=93bXS9wX68wCDk_m and here is the tool itself: amzn.to/47Xdmnh I hope this helps!
We fix around 7 sets a year but we don't have a ton of lights either. Thanks for the links too, saves me from hunting for the connectors. Excellent tutorial 🛠🎅
Hello, Maria and happy holidays to you. I just interviewed John DeCosmo, the inventor of the LED Keeper: ua-cam.com/users/live_O-9UtqxqzM?si=HopCwlSeLzBFKKgv I asked him this same question. He educated me that lights with control boxes and pre-lit trees are not designed to be fixable and normally fail within 1 year. With that said, one option that works out about 70% of the time is to contact the manufacture. A lot of times the lights are under a warranty that you didn't know they had! You do want to make sure that the string is actually carrying power to the bulb's though. You can either use a voltage detector or a multimeter and see if the string is carrying power but just not illuminating. If you don't have either tool, you can test the lights by daisy-chaining another light set to it. If that set lights up, then you know the "bad" string has power but isn't lighting. Lastly, an option is to check to see if the box has a reset button. Many times owners aren't aware of the reset option or there are fuses in the box that need to be checked or replaced. You can check fuses with this tool: amzn.to/3t3HcaJ The LED Keeper is my go-to light tool!
@ChristmasOnCrestline Thank you so much for your quick response. I will try all your suggestions to see if I can get them to work. Once again, thank you.
This is so cool!!! Thanks for this video today. I was literally going to go out to Menards today to see what kits exist to fix my lights and now I know that I can do this instead. We always have to fix a dozen or so lights from the squirrels that love to snack on our holiday lights. Cheers!
Glad it was helpful! I'm not aware of any repair kits that exist at the stores. But...that's a great idea. Squirrels are the enemy of Christmas lights lol.
This is amazing! Our tree lights just broke just like that and this is gonna save us so much 💗 what is the tool called that you used to strip the green plastic off the wire?
So far I have about 40% of my Christmas lights up and I did about 10 sets I needed to fix my dad comes in handy my dad usually fixes most of them for me I give him them and while he's watching TV he fixes them
Do you have any videos on how you fix a Christmas tree the ones that have the lights all connected on the branches I have one set I remember from last year out I didn't put the Christmas tree up yet but I can't even check it section-by-section because the whole tree has to be plugged in together is there an easy way you know of the check that because there's no wires the wires are all in this stem in that stick that goes down the middle
I don't have any videos on it, Rob. I don't own a pre-lit tree so I don't have any experience with it. If you are talking about a Twinkly Tree, those use fiber optic lights which, if memory serves, can't be replaced. If they are incandescent lights, Ulta-Lit has a video on that: ua-cam.com/video/xrXRxOIjVm0/v-deo.html
Glad to hear the tulip lights fix worked for you! Sometimes a simple solution like black tape can do wonders. And I'm thrilled you liked the Christmas background-it's all about spreading that festive cheer! Wishing you a fantastic New Year filled with joy and bright moments!
Question, so I have a set of lights where the last section isn't working, so I took my Lowes version of led keeper and hooked it up and I managed to get all of the lights to work via the tool but only on each side of what I believe is called a current limiting pod if I put tool on 1 side it lights up all lights on that side if I do it on the other side it lights all the lights on that side. But when I plugin that section won't work. Can I repair that?
Hello, Jerry. I spent about several hours repairing LEDs with my LED Keeper yesterday. I think you're describing what happened to me on a few strings. I had five or so strings that had a corroded light socket. I removed that socket, heat shrinked the wires back together, and they all worked just fine. The trick is to utilize a flashlight. When everything seems like they should function but doesn't, use a flashlight to check the inside of the bad bulbs socket, often times you'll find corrosion and all is well by simply removing it.
This is fantastic. Thanks so much for doing this. Love the wire stripper recommendations. I've been using the same couple of cheap ones for 30 years. These are easier. Came looking for a similar video but for soldering outdoor Christmas light yard art (Santa on a roller coaster with a few light and sound effects) to an old transformer (really just need the wire connector cap but the 10-12 gauge mentioned in the video helped with this!). I'll keep looking. Hopefully you have one! Thanks again and Merry Christmas!
I'm thrilled you like this video, Chris. I use this method at least 10 times each season. Kansas wildlife loves to munch on these lights for some reason! We do have one soldering video but it is angled towards using soldering as a method of repurposing light strings as extension cords. You can find that video here: ua-cam.com/video/wA_U1QsaDeU/v-deo.htmlsi=g_WYsQmlg4u1iFIz The soldering comes in about the 4:00 mark or so.
I fix 15-20 sets per year, whenever I have a broken socket or wire between sockets I just take parts from a scrap set and replace the socket or broken wire by pushing out the brass contact barb from the sockets and inserting the wire with contacts from the scrap set, I do this with both incandescent and LED sets. I have also added extra sockets in incandescent sets so I can lower the voltage on the bulbs and make them last longer or if I just need a few extra bulb to complete a garland. It may take a little extra time, but it retains the insulation of all the wires in the lights and you don't loose any bulbs
That's a really smart idea, JM. Putting strain on the lights is what causes a lot of burn outs. I bet lowering the voltage does help with their longevity.
I stapled through my new patio string lights and was completely devastated. Deff going to try this, since my lights were NOT cheap and it would be a shame to throw them out
This is a handy trick, Alexandra. I the past, used a wire nut and electric tape but this is the much better option. Plus, this looks alot cleaner compared to the bright orange wire nuts!
I have lights in a lighted train that somehow have wires cut, but when stripping them, the inside isn't electrical wire, but rather a fiber optic looking material. Are these fixable or do i just need to throw it out?
I would imagine you have some rogue squirrels on your property. That is my most common cause of mysteriously cut strings. I've not heard of fibers in a light string. I presume this is not a normal LED set of lights. I would say to test them and find out. I would use a wire twist to connect these fibers and see if they transmit power and illuminate the lights. I hope these work out for you!
@Christmas on Crestline after commenting, I plugged it in and got to work. I have no idea what that wire does. I was able to get almost all the lights lit. Those wires are in more than one area and the lights that don't light after replacing many bulbs are one strand, so that wire must not affect function. I am using the train as it is. I am probably the only one that will know they aren't lit
@@harvestingharrolds1086 That's a fair point most of us don't realize, HH. We see what we consider to be flawed while the audience only sees the wonder of the lights.
You probably don't need this info after all this time, but if somebody else does, I think the one you're describing is just a "support wire" some of the other videos mention, which is simply there to strengthen the net or help it hold its form. No actual wire is inside it.
I don't see it mentioned here right off, but it seems other videos have noted that the net or string is designed so that the mains voltage divided by the total number of lights in series comes out to the low level AC voltage those bulbs are made to handle (a couple volts). There was a warning that allowing the modern "shunt equipped" bulbs to stay in the chain after they burn out would effectively bypass the dead bulb and bump up the individual voltages on the remaining live ones, possibly burning out more of them and further increasing the voltages. Wouldn't removing one and splicing the line have the same effect?
For incandescent bulbs? Yes. I just interviewed John DeCosmo about this topic. John is the inventor of the Keeper repair tools for lights: ua-cam.com/users/live_O-9UtqxqzM?si=ZVsADGy-kAOQ6FTg In the video he mentions that strings are designed to last only a few seasons. The states that once one bulb is bad there is a chain reaction where the likelihood of other failures greatly increases.
That's a unique problem, Amanda. The solution would be to strip them back a 1/2 inch or so to the copper , Then simply touch the wires to one another until you find the correct combo that illuminates the lights. Then permanently connect them. With that said, you should be able to visually see the pattern but if it is too mangled, use the touch test method. I hope that helps.
Your basic idea is good, but the advice/details are way off. Specifically those small wires you're splicing are probably 18 or 20 gauge (larger numbers mean smaller wires). Recommending a 10-12 gauge (yellow) butt splice is wrong. Those crimp connectors are color-coded based on the size of the wire, red is 18-22ga, blue is 14-16ga and yellow is 10-12ga. For this job, RED connectors would be ideal.
What if there are 3 wires? I have a set of purple led from Halloween they're so much prettier than the purple Christmas version (idk why) but they separated at the fuse...
You're right. Halloween purples seem to pop more for some reason. Three wires can be tricky but can usually be done if you bypass that three wired bulb. If that is the bad bulb, cut it out, and fuse the next bulb to the string with shrink tube. That will save the string for you.
I fix exactly ZERO Christmas lights per year but 2022 is my year! I've got a prelit tree (incandescent) with a melted bulb socket. One wire going into it has current, the other does not. The bulb that follows that "dead" wire lights up when I remove it and test it. Can you tell me if I can just use this technique to get rid of the melted socket?
You should be able to, yes, Janice. Although, I would add that most pre-lit trees are not designed to be fixed. But if you have a melted socket, it needs to go away and this method should work for you just fine.
@@ChristmasOnCrestline Thanks! I’m going to try this out. Just bought the damn thing a year ago and never registered it, so no luck on the 2 year warranty.
Oh no! Dealing with a dog-chewed Christmas light strand is tricky, but here's a quick fix for the four wires. Sometimes, the wires in a Christmas light strand are color-coded. Commonly, there are two wires for power (usually one is hot and the other neutral), one for ground, and one for data (for programmable lights). Identify which wire is which. If there's visible damage, match the corresponding wires by color. Twist together the corresponding wires - power to power, ground to ground, etc. Use soldering or heat shrinking to secure the twisted wires. Or, if you use wire connectors, make sure they are suitable for outdoor use! Test the Lights! Before reinstalling the strand, plug it in and test the lights to ensure that the repaired section is working correctly. If the damage is extensive, and the wires are significantly frayed, you might need to consider trimming the damaged portion and splicing in a new section of wire. Remember to prioritize safety, and if you're uncomfortable with the repair, it's always a good idea to seek assistance from someone experienced with electrical work. I hope this helps, and good luck with fixing your lights! Let me know how it goes!
@@ChristmasOnCrestline this is the terminal end of the strand. I’m not trying to splice two wires back together. The wires are all green coated. No lines or dots on coating to differentiate
Actually, its at 4:54, Troy. That's why I provide timeline chapters for folks to jump ahead. You must have missed those while you were waiting patiently.
It's funny the thing used to fix the Christmas trees the light fixture I watched your video I went to Home Depot I'm walking in the parking lot the next day after your video and guess what I found somebody left in that cost so I actually got it for free
@@ChristmasOnCrestline I feel bad cuz I wish I would have known who the person is but I've known people who brought stuff back that they found in the carts into the store and the people go back to the store and they still don't get their item usually the person that works in the store just keeps the item that's why I kept it
I spend hours fixing lights. I do have a device that finds the dead bulb for me. However I want to know how to fix strands that are torn (aka wire broken) . We have tall trees that the lights are hard to remove from and the lights get torn during the removal process. Of course the trees have 400 lights strings on them which are the most expensive. He sent why I’m watching this. Ironically have all these supplies already.
That's ironic that you mention fixing already hung lights. I had some roofline C7 greens go out on me last weekend. I had to MacGuyver a way to find the bad bulb without removing all five colors from the roof. After some thought, I came up with a super easy fix. I went to record a video on it Monday but my neighbor decided to build a new deck next to me so the noise prevented it. So, that will be forthcoming. For fixing already hung severed wires, you likely can't use a heat shrink method due to the fire hazard of the tree and danger of damaging other cords. So, you'll likely have to strip back the wire, use a wire nut, electrical tape, then duct tape. That will bring the lights back to life for the season. You can permanently fix them in the off season..
What if the wires look fine, but the light stops working? I clipped all 3 wires and put them together with a connector. It did not work and I'm at a loss.
Hello. Tia. One thing that sometimes happens but most folks don't know to look for is the wires will be positive or negative and the positive wire will have teeny tiny white lettering. That lettering signifies it's the positive. You might check that you have the wires correctly connected positive to positive. I mention that because I'm assuming that you've used the LA D keeper to test that the lads are OK?
Sorry, I was in the middle of writing that and my phone rang and it hit send for some reason. I'm guessing that you tested the lights and that they are all functioning bulbs?
Hey there. Good to see you. I think with everyone's lights still sitting in the Pacific Ocean, this will be a huge year for repairing broken Christmas lights! Sounds like you save yourself $100+ every year
I have lights for all the holidays and I had a socket failure on my pumpkin lights now I can fix them there isn't a holiday I don't decorate for valentines day at Patty day Easter memorial Day 4th of July then my big one Halloween and Christmas not any lights for Turkey day but plenty of inflatables
Hey there, Jody! Man, I bet you have the whole neighborhood covered with holiday cheer! You're definitely dedicated to spreading that holiday spirit-covering everything from Valentine's Day to Halloween and Christmas is impressive! If you aren't aware, I do an annual contest where folks send me videos of their displays, and I put them together in an end-of-year video. I'd love to have you send in some footage-I'm sure your setups will inspire others to add new props to their displays. Feel free to email it to ChristmasOnCrestline@gmail.com. I can't wait to see what you've created!
Fair enough, David. After reading your comment, I rewatched this and I agree. I'll release a more precise version and just show the fix for the problem. Thanks for letting me know.
do anyone know how to light up one or two bulb ? I tried with a 3VAC for one and two bulbs NOGO. If you multiply 2.5 volts by 48, you get 120 volts, and originally, that's how many bulbs the strands has. We must remember this is AC not DC .. so in theory 3.5 volt AC should light up one bulb unless requires 120V and dividing is not possible. all bulbs are different...some LED's and some incandescent bulb.More than like is that bulb
Hey there, Supernova. To light up a single Christmas light bulb, first identify whether it's incandescent or LED and its voltage requirement. For an incandescent bulb from a 120V strand with 50 bulbs, it likely needs around 2.4V AC, so a 3V AC source should work. For LED bulbs, ensure you match the specific voltage and use the correct AC or DC power source. LEDs often have built-in resistors and might require a specific voltage, usually lower than the strand’s total voltage divided by the number of bulbs. Always check the bulb specifications before applying power to avoid damage. I hope that answers your question.
I'm way ahead of ya, Star. You watched the long video that is meant for the folks that tune in each week. Here is the video condensed video that gets on with it: ua-cam.com/video/DXWullu2FTk/v-deo.html I hope you're able to fix your lights!
Wasted 3 minutes of my life at the beginning. Bro spread it out thru the video. Bet you'll get more views. But thanks for making it worth me sticking around. Helped me come up with a solution. You almost lost me tho.
Boom! I just rewatched this and you're right. That's a reasonable and fair comment. I think I'll trim it up and release it as a new video to help folks get to the information more quickly. Thanks for the advice.
Why does it take you 40 minutes to get to the point. I NEED TO FI MY CHRISTMAS LIGHTS NOT HEAR YOUR SOB STORY ABOUT A SQUIRRELL CHEWING THEM. thank you.
Great point, Justine! To make it easier for everyone, I include chapters in all of my videos. That way, viewers who are short on time or just need the fix can jump straight to the relevant section. I try to create a mix of helpful tips and entertainment for those who enjoy the whole show. Thanks for watching, and Merry Christmas!
Hello, Paul. We use the timeline chapters in this video to avoid wasting folks time. They allow you to jump right to the part you are wanting to watch.
This video was a waste of time. I've in all my years never had this particular problem with this type of light. Also, these lights are 16-22 guage wire. A lot smaller than the connector he was using for the wire. Unsafe.
That's awesome, Jimmmy, that in all your years, you've never had a single wire be severed by squirrels. Whatever you are using to keep your light strings away from wildlife...patent that! Well done you. Merry Christmas.
Terrible advice. Never use a 10 - 12 gauge butt connector on a 16 gauge or smaller wire, no matter what you say. The only reason your wires may not have pulled out is only due to the heat shrink of the connector. A properly made electrical connection would be using the properly sized crimp connector for the wire gauge being repaired as in any and all electrical repairs. That's why there are different sized crimp connectors. You are a cobbler, giving uninformed advice to viewers which may cause the repair to fail, and require an additional proper fix using the correct connector for the wire gauge or size being repaired. I dare you to do a strong pull test on your crimped connection of the wires on these mini light sets with YOUR recommended 10 to 12 gauge connector BEFORE heat shrinking the connector. Because of my extensive experience with crimp connectors and how they work in both AC circuits and DC automotive circuits, I would put my money on that the connection will come apart. Your repair only covers a broken wire. These light sets have many more common failures which are due to burnt out bulbs, burnt out bulbs with bad shunts, blown fuses and faulty bulb sockets. To repair the most common failures of Christmas light sets, I recommend to all viewers to buy the LightKeeper Pro (for incandescent light sets) or the LED Keeper (for LED Light sets), which can be found at any Menards, Lowes, Walmart, Hobby Lobby or on Amazon. In all my years fixing Christmas lights, the only time I had a broken wire that caused the lights not to work was when animals chewed through the wire. There are many much better UA-cam videos for Christmas light set repairs, most of which use the LightKeeper Pro or the LED Keeper.
Thanks for watching, David. I also recommend to all viewers to use Ulta-Lit's Keeper products to fix bulb and shunt issues. The Keepers are amazing products. I have several videos on those tools as well. I think you skipped the part about this cut wire being a squirrel caused issue. Squirrels do love them some Christmas lights.
lmao his guy clearly has never watched one of the videos on this channel before. Dude, figure it out before you leave an uneducated comment. Your are a cobbler of a commenter and would be better served running for congress with the other schmucks who spew asinine remarks.
I spend hours fixing lights. I do have a device that finds the dead bulb for me. However I want to know how to fix strands that are torn (aka wire broken) . We have tall trees that the lights are hard to remove from and the lights get torn during the removal process. Of course the trees have 400 lights strings on them which are the most expensive. He sent why I’m watching this. Ironically have all these supplies already.
That's ironic that you mention fixing already hung lights. I had some roofline C7 greens go out on me last weekend. I had to MacGuyver a way to find the bad bulb without removing all five colors from the roof. After some thought, I came up with a super easy fix. I went to record a video on it Monday but my neighbor decided to build a new deck next to me so the noise prevented it. So, that will be forthcoming. For fixing already hung severed wires, you likely can't use a heat shrink method due to the fire hazard of the tree and danger of damaging other cords. So, you'll likely have to strip back the wire, use a wire nut, electrical tape, then duct tape. That will bring the lights back to life for the season. You can permanently fix them in the off season.
I just started a Christmas Tree Repair business and your video was just what I needed to see. Now I can finish pulling out burnt out lights an putting in new ones only 900 light to change. (Green Holiday Tree Lighting Company) Interior Christmas Tree replacing lights and stripping of lights.
Very cool, Mark. This will save you some cash and fast-track your fixes! Let me know how your season goes! Best of luck to ya!
Thanks!
You are welcome!
Hey, thanks, Gab! That's very kind of you. Have a great season!
You are welcome! And a great season to you, too! @@ChristmasOnCrestline
Thank you yo are a life saver got a new puppy and chew the lights during the night and need a permanent fix. Again thank you!!
That's a classic puppy manuver. Happy to help, Itzia!
dont want a bloody history of your life just repair the damn lights lool
Always nice to hear from a fan. Merry Christmas.
Didn't know u can fix them...Have a Blessed day
You know, a lot of folks don't know about this fix. But, it's dang helpful and saves you money 😁
I fix 10-12 sets each year, either from dead bulbs or busted wires. Speaking of moisture protection, are you concerned about the led keeper puncturing all those tiny holes in the wires? Its definitely crossed my mind since I've seen many times what a wire puncture can do to car wiring. That's my go to method for wire repairs except I use the pink connectors and a dedicated crimping tool, far better than that crimper in those strippers.
Hey there, Scott. I'm not worried about the puncture. The plastic is meant to self-heal. I asked that question to a light company and to Ulta-Lit last year and to they said the same thing. So, after fixing lights on a few strings, I went back and looked at the wire and couldn't find that holes a day or two later.
FREAKING AWESOME YOU SAVED ME FROM RE-RUNNING ALL MY CHRISTMAS LIGHTS 🎄🦌🎅
Awesome, Rogello. I'm thrilled I could help!
This will make a great gift package for my uncle. He hangs lights like you do and always complains about broken lights. Thanks so much for the gift idea and the links!!🎁🎄👍
Good call, WC!
Great tips, another great video. Thanks for (teaching) and sharing. Have a happy and safe rest of your week!
Hey there, Lou. For some weird reason, I really do enjoy fixing lights.
SKIP TO 5 MIN IF IN A HURRY🙆
Thanks, Shaun!
I am being introduced to the beauty and prowess of squirrel.
Classic squirrel maneuver lol.
Helpful tips, thanks!
Glad I could help! Merry Christmas!
Can you do this for a fairy led net
You can, yes. All we are doing here is reattaching the line of power. The heat shrink acts as a new coating and protects the line from breaking.
Man, you are a handy channel to know about! This video saved me from buying new lights and spending $100+ this weekend. Thanks for this!
Glad I could help!
Thank you for this and for the product links! I went to put lights up but something got to them and chewed through several wires and I can't remember where I bought them to color match the rest. So, I need to fix them and this video saves the day!
Glad I could help! I provide product links in all my videos nowadays. Helps for those that want to use the same stuff that I use to fix lights.
Can this be done on outdoor string lights? Not sure if it would be weather proof.
Hey there, Ana. Heat shrinking does make it waterproof.
Great video thanks! What about when all 3 wires have been cut? Any tips for matching them up?
Sometimes, you might need a magnifying glass or use your phone and zoom in. But one of the wires will have tiny white writing on it, which makes it the positive wire. One wire will be positive, one will be a negative wire, and the 3rd wire will have the lights attached to it.
@@ChristmasOnCrestline thanks! i just came inside from doing this project. all went well except the heat gun singed a bit of the existing wire coating. probably ran it too hot. didn't look like copper wire was exposed but wrapped it in electrical tape. think that will be fine?
I think you're good, yes! Great job! It'll all get easier with practice.
Can I use regular shrink tubing instead of the shrink connectors?
You could, if you just want a water-tight seal. The connectors ensure the wires maintain a connection though.
Does this work for both incandescent and led. The light keep tool says you must have a resistor like in the pod when you remove a socket and connect the wires together
No, this only works for LED strings. They mention the rectifier as only LED strings have those. For in candescent lights we have to use the LIght Keeper Pro. Here are two videos showing this tool: ua-cam.com/video/4vYBVp4m9dY/v-deo.htmlsi=WHQp44LVjg0jm5zd ua-cam.com/video/tV0FepnwZuc/v-deo.htmlsi=93bXS9wX68wCDk_m and here is the tool itself: amzn.to/47Xdmnh I hope this helps!
I just got in the Irwin vise grip wire cutters, One question...How did I live without these for the last 50 years.
Um, yes, I asked that same exact question, Gaetano. They are a game changer.
We fix around 7 sets a year but we don't have a ton of lights either. Thanks for the links too, saves me from hunting for the connectors. Excellent tutorial 🛠🎅
No worries, Crepe. Glad I can help.
How do I fix led lights on xmas tree with control box? Nothing is working?
Hello, Maria and happy holidays to you. I just interviewed John DeCosmo, the inventor of the LED Keeper: ua-cam.com/users/live_O-9UtqxqzM?si=HopCwlSeLzBFKKgv I asked him this same question. He educated me that lights with control boxes and pre-lit trees are not designed to be fixable and normally fail within 1 year. With that said, one option that works out about 70% of the time is to contact the manufacture. A lot of times the lights are under a warranty that you didn't know they had! You do want to make sure that the string is actually carrying power to the bulb's though. You can either use a voltage detector or a multimeter and see if the string is carrying power but just not illuminating. If you don't have either tool, you can test the lights by daisy-chaining another light set to it. If that set lights up, then you know the "bad" string has power but isn't lighting. Lastly, an option is to check to see if the box has a reset button. Many times owners aren't aware of the reset option or there are fuses in the box that need to be checked or replaced. You can check fuses with this tool: amzn.to/3t3HcaJ The LED Keeper is my go-to light tool!
@ChristmasOnCrestline Thank you so much for your quick response. I will try all your suggestions to see if I can get them to work. Once again, thank you.
This is so cool!!! Thanks for this video today. I was literally going to go out to Menards today to see what kits exist to fix my lights and now I know that I can do this instead. We always have to fix a dozen or so lights from the squirrels that love to snack on our holiday lights. Cheers!
Glad it was helpful! I'm not aware of any repair kits that exist at the stores. But...that's a great idea. Squirrels are the enemy of Christmas lights lol.
This is amazing! Our tree lights just broke just like that and this is gonna save us so much 💗 what is the tool called that you used to strip the green plastic off the wire?
Hey there, Lexi. This should help you out. The tool is Klein Tools Wire Stripper/Cutter: amzn.to/47FG9fZ
@@ChristmasOnCrestline thank you!! 😍
So far I have about 40% of my Christmas lights up and I did about 10 sets I needed to fix my dad comes in handy my dad usually fixes most of them for me I give him them and while he's watching TV he fixes them
Dads are great for sitting down and fixing lights while watching TV. I could teach a class on it lol.
This is great info 👍
Hey there! I imagine you're as busy as we are! 😁🎄
Do you have any videos on how you fix a Christmas tree the ones that have the lights all connected on the branches I have one set I remember from last year out I didn't put the Christmas tree up yet but I can't even check it section-by-section because the whole tree has to be plugged in together is there an easy way you know of the check that because there's no wires the wires are all in this stem in that stick that goes down the middle
I had that issue with my old pre lit tree. Wasn't worth the effort so I just put my own lights on. Pre lit is the devil!
I don't have any videos on it, Rob. I don't own a pre-lit tree so I don't have any experience with it. If you are talking about a Twinkly Tree, those use fiber optic lights which, if memory serves, can't be replaced. If they are incandescent lights, Ulta-Lit has a video on that: ua-cam.com/video/xrXRxOIjVm0/v-deo.html
Thank you for your suggestions, quick fix on my tulip lights, to do black tape, hopefully it works Ps love Christmas background and Happy New Year!
Glad to hear the tulip lights fix worked for you! Sometimes a simple solution like black tape can do wonders. And I'm thrilled you liked the Christmas background-it's all about spreading that festive cheer! Wishing you a fantastic New Year filled with joy and bright moments!
Does this work for LED ??
Actually, this fix is specifically for LED lights, Erin. You're good to go!
Question, so I have a set of lights where the last section isn't working, so I took my Lowes version of led keeper and hooked it up and I managed to get all of the lights to work via the tool but only on each side of what I believe is called a current limiting pod if I put tool on 1 side it lights up all lights on that side if I do it on the other side it lights all the lights on that side. But when I plugin that section won't work. Can I repair that?
Hello, Jerry. I spent about several hours repairing LEDs with my LED Keeper yesterday. I think you're describing what happened to me on a few strings. I had five or so strings that had a corroded light socket. I removed that socket, heat shrinked the wires back together, and they all worked just fine. The trick is to utilize a flashlight. When everything seems like they should function but doesn't, use a flashlight to check the inside of the bad bulbs socket, often times you'll find corrosion and all is well by simply removing it.
This is fantastic. Thanks so much for doing this. Love the wire stripper recommendations. I've been using the same couple of cheap ones for 30 years. These are easier.
Came looking for a similar video but for soldering outdoor Christmas light yard art (Santa on a roller coaster with a few light and sound effects) to an old transformer (really just need the wire connector cap but the 10-12 gauge mentioned in the video helped with this!). I'll keep looking. Hopefully you have one! Thanks again and Merry Christmas!
I'm thrilled you like this video, Chris. I use this method at least 10 times each season. Kansas wildlife loves to munch on these lights for some reason! We do have one soldering video but it is angled towards using soldering as a method of repurposing light strings as extension cords. You can find that video here: ua-cam.com/video/wA_U1QsaDeU/v-deo.htmlsi=g_WYsQmlg4u1iFIz The soldering comes in about the 4:00 mark or so.
Great Info Charlie! My mom has 2 sets that she wanted to fix. I will have to get the ol' crimpers out and show her how its done. Thanks Friend!😀
You know it's almost the holiday season when your asked to help with Christmas decorations lol. 🎅👍
@@ChristmasOnCrestline lol that’s for sure😂
I fix 15-20 sets per year, whenever I have a broken socket or wire between sockets I just take parts from a scrap set and replace the socket or broken wire by pushing out the brass contact barb from the sockets and inserting the wire with contacts from the scrap set, I do this with both incandescent and LED sets. I have also added extra sockets in incandescent sets so I can lower the voltage on the bulbs and make them last longer or if I just need a few extra bulb to complete a garland. It may take a little extra time, but it retains the insulation of all the wires in the lights and you don't loose any bulbs
That's a really smart idea, JM. Putting strain on the lights is what causes a lot of burn outs. I bet lowering the voltage does help with their longevity.
Do you have a video on adding and extra socket?
I stapled through my new patio string lights and was completely devastated. Deff going to try this, since my lights were NOT cheap and it would be a shame to throw them out
This is a handy trick, Alexandra. I the past, used a wire nut and electric tape but this is the much better option. Plus, this looks alot cleaner compared to the bright orange wire nuts!
I have lights in a lighted train that somehow have wires cut, but when stripping them, the inside isn't electrical wire, but rather a fiber optic looking material. Are these fixable or do i just need to throw it out?
I would imagine you have some rogue squirrels on your property. That is my most common cause of mysteriously cut strings. I've not heard of fibers in a light string. I presume this is not a normal LED set of lights. I would say to test them and find out. I would use a wire twist to connect these fibers and see if they transmit power and illuminate the lights. I hope these work out for you!
@Christmas on Crestline after commenting, I plugged it in and got to work. I have no idea what that wire does. I was able to get almost all the lights lit. Those wires are in more than one area and the lights that don't light after replacing many bulbs are one strand, so that wire must not affect function. I am using the train as it is. I am probably the only one that will know they aren't lit
@@harvestingharrolds1086 That's a fair point most of us don't realize, HH. We see what we consider to be flawed while the audience only sees the wonder of the lights.
You probably don't need this info after all this time, but if somebody else does, I think the one you're describing is just a "support wire" some of the other videos mention, which is simply there to strengthen the net or help it hold its form. No actual wire is inside it.
Charlie is this ok for Led lights?
It's absolutely okay for LEDs, Gaetano. The lights I used in this demonstration are LED minis.
Good stuff. Thanks bud.
I'm happy this helped ya, Asciepius.
Thank you thank you thank 🙏🏻
I'm happy to have helped, Blue!
I don't see it mentioned here right off, but it seems other videos have noted that the net or string is designed so that the mains voltage divided by the total number of lights in series comes out to the low level AC voltage those bulbs are made to handle (a couple volts). There was a warning that allowing the modern "shunt equipped" bulbs to stay in the chain after they burn out would effectively bypass the dead bulb and bump up the individual voltages on the remaining live ones, possibly burning out more of them and further increasing the voltages. Wouldn't removing one and splicing the line have the same effect?
For incandescent bulbs? Yes. I just interviewed John DeCosmo about this topic. John is the inventor of the Keeper repair tools for lights: ua-cam.com/users/live_O-9UtqxqzM?si=ZVsADGy-kAOQ6FTg In the video he mentions that strings are designed to last only a few seasons. The states that once one bulb is bad there is a chain reaction where the likelihood of other failures greatly increases.
If my dog chewed through all 3 wires, how can I tell which wire to connect to which wire?
That's a unique problem, Amanda. The solution would be to strip them back a 1/2 inch or so to the copper , Then simply touch the wires to one another until you find the correct combo that illuminates the lights. Then permanently connect them. With that said, you should be able to visually see the pattern but if it is too mangled, use the touch test method. I hope that helps.
Your basic idea is good, but the advice/details are way off. Specifically those small wires you're splicing are probably 18 or 20 gauge (larger numbers mean smaller wires). Recommending a 10-12 gauge (yellow) butt splice is wrong. Those crimp connectors are color-coded based on the size of the wire, red is 18-22ga, blue is 14-16ga and yellow is 10-12ga. For this job, RED connectors would be ideal.
Thanks for the information, Rig!
What if there are 3 wires? I have a set of purple led from Halloween they're so much prettier than the purple Christmas version (idk why) but they separated at the fuse...
You're right. Halloween purples seem to pop more for some reason. Three wires can be tricky but can usually be done if you bypass that three wired bulb. If that is the bad bulb, cut it out, and fuse the next bulb to the string with shrink tube. That will save the string for you.
Hey ol boy, you still out playing Santy Claus! Thx 💯
Indeed I am lol
I fix exactly ZERO Christmas lights per year but 2022 is my year! I've got a prelit tree (incandescent) with a melted bulb socket. One wire going into it has current, the other does not. The bulb that follows that "dead" wire lights up when I remove it and test it. Can you tell me if I can just use this technique to get rid of the melted socket?
You should be able to, yes, Janice. Although, I would add that most pre-lit trees are not designed to be fixed. But if you have a melted socket, it needs to go away and this method should work for you just fine.
@@ChristmasOnCrestline Thanks! I’m going to try this out. Just bought the damn thing a year ago and never registered it, so no luck on the 2 year warranty.
Oh man, that's the worst!
You did that the hardest way possible.
I love learning new ways to permanently fix lights, Chris. What you do you do that is easier than heat shirking?
How to fix the end of a strand the dog chewed up? There are 4 wires. How do you know how to terminate them?
Oh no! Dealing with a dog-chewed Christmas light strand is tricky, but here's a quick fix for the four wires. Sometimes, the wires in a Christmas light strand are color-coded. Commonly, there are two wires for power (usually one is hot and the other neutral), one for ground, and one for data (for programmable lights). Identify which wire is which. If there's visible damage, match the corresponding wires by color. Twist together the corresponding wires - power to power, ground to ground, etc. Use soldering or heat shrinking to secure the twisted wires. Or, if you use wire connectors, make sure they are suitable for outdoor use! Test the Lights! Before reinstalling the strand, plug it in and test the lights to ensure that the repaired section is working correctly. If the damage is extensive, and the wires are significantly frayed, you might need to consider trimming the damaged portion and splicing in a new section of wire.
Remember to prioritize safety, and if you're uncomfortable with the repair, it's always a good idea to seek assistance from someone experienced with electrical work.
I hope this helps, and good luck with fixing your lights! Let me know how it goes!
@@ChristmasOnCrestline this is the terminal end of the strand. I’m not trying to splice two wires back together. The wires are all green coated. No lines or dots on coating to differentiate
4:58 when he finally begins repair
Actually, its at 4:54, Troy. That's why I provide timeline chapters for folks to jump ahead. You must have missed those while you were waiting patiently.
It's funny the thing used to fix the Christmas trees the light fixture I watched your video I went to Home Depot I'm walking in the parking lot the next day after your video and guess what I found somebody left in that cost so I actually got it for free
Someone left a Keeper in the lot? Nice find. Was is it the yellow LED Keeper or the red Light Keeper Pro?
@@ChristmasOnCrestline I feel bad cuz I wish I would have known who the person is but I've known people who brought stuff back that they found in the carts into the store and the people go back to the store and they still don't get their item usually the person that works in the store just keeps the item that's why I kept it
Fair enough. I'm chatting chalking it up to a Christmas light miracle! Lol
This will be the first
Good luck to you, Laurie!!! This will save you a ton of $$$
Wow lol I didn't even know this was possible I really appreciate this info!!!!
Glad it was helpful!😁🎅
Yay
Indeed
I spend hours fixing lights. I do have a device that finds the dead bulb for me. However I want to know how to fix strands that are torn (aka wire broken) . We have tall trees that the lights are hard to remove from and the lights get torn during the removal process. Of course the trees have 400 lights strings on them which are the most expensive. He sent why I’m watching this. Ironically have all these supplies already.
That's ironic that you mention fixing already hung lights. I had some roofline C7 greens go out on me last weekend. I had to MacGuyver a way to find the bad bulb without removing all five colors from the roof. After some thought, I came up with a super easy fix. I went to record a video on it Monday but my neighbor decided to build a new deck next to me so the noise prevented it. So, that will be forthcoming. For fixing already hung severed wires, you likely can't use a heat shrink method due to the fire hazard of the tree and danger of damaging other cords. So, you'll likely have to strip back the wire, use a wire nut, electrical tape, then duct tape. That will bring the lights back to life for the season. You can permanently fix them in the off season..
What if the wires look fine, but the light stops working? I clipped all 3 wires and put them together with a connector. It did not work and I'm at a loss.
Hello. Tia. One thing that sometimes happens but most folks don't know to look for is the wires will be positive or negative and the positive wire will have teeny tiny white lettering. That lettering signifies it's the positive. You might check that you have the wires correctly connected positive to positive.
I mention that because I'm assuming that you've used the LA D keeper to test that the lads are OK?
Sorry, I was in the middle of writing that and my phone rang and it hit send for some reason. I'm guessing that you tested the lights and that they are all functioning bulbs?
I usually fix about 10-20 stings of lights per year.
Hey there. Good to see you. I think with everyone's lights still sitting in the Pacific Ocean, this will be a huge year for repairing broken Christmas lights! Sounds like you save yourself $100+ every year
I have lights for all the holidays and I had a socket failure on my pumpkin lights now I can fix them there isn't a holiday I don't decorate for valentines day at Patty day Easter memorial Day 4th of July then my big one Halloween and Christmas not any lights for Turkey day but plenty of inflatables
Hey there, Jody! Man, I bet you have the whole neighborhood covered with holiday cheer! You're definitely dedicated to spreading that holiday spirit-covering everything from Valentine's Day to Halloween and Christmas is impressive! If you aren't aware, I do an annual contest where folks send me videos of their displays, and I put them together in an end-of-year video. I'd love to have you send in some footage-I'm sure your setups will inspire others to add new props to their displays. Feel free to email it to ChristmasOnCrestline@gmail.com. I can't wait to see what you've created!
I fix about 20 to 30 sets a season
You're right in line with me, Brandon. 20 x $8(ish) a string...that's a few dollars. Smart idea to repair them.
@@ChristmasOnCrestline I sent you a message on FB on what I use to splice my broke wires together
Very cool. I'll check it out, thanks.
All talk not much info
Fair enough, David. After reading your comment, I rewatched this and I agree. I'll release a more precise version and just show the fix for the problem. Thanks for letting me know.
"Santas Best" lights have 5 wires, not two. I don't know how to fix those from watching your video. :(
Wow. Five wires is rare. I will say, if there are LED lights then this will still for you.
do anyone know how to light up one or two bulb ? I tried with a 3VAC for one and two bulbs NOGO. If you multiply 2.5 volts by 48, you get 120 volts, and originally, that's how many bulbs the strands has. We must remember this is AC not DC .. so in theory 3.5 volt AC should light up one bulb unless requires 120V and dividing is not possible. all bulbs are different...some LED's and some incandescent bulb.More than like is that bulb
Hey there, Supernova. To light up a single Christmas light bulb, first identify whether it's incandescent or LED and its voltage requirement. For an incandescent bulb from a 120V strand with 50 bulbs, it likely needs around 2.4V AC, so a 3V AC source should work. For LED bulbs, ensure you match the specific voltage and use the correct AC or DC power source. LEDs often have built-in resistors and might require a specific voltage, usually lower than the strand’s total voltage divided by the number of bulbs. Always check the bulb specifications before applying power to avoid damage. I hope that answers your question.
@@ChristmasOnCrestline It worked ...TY so much
That's great to hear. Well done, you!
At least 50 sets
Wow! You are amazing. Well done, you!
Tested Fuse ok. Tested entire string..power ok yet no lights: Help
Sounds like you likely have a copper issue, Dennis. Call 8888582548 and they'll walk you through the solution!
Skip to 5m to actually see the repair 😂
We already had that marked with the timestamp chapters but it's still a great call, Takashi.
I fix about 10 light sets a year
Hello, Jose. That saves you nearly $100 a year, I'd bet. Very nice.
Can we just get on with it. You list my interest when you start talking about money.
I'm way ahead of ya, Star. You watched the long video that is meant for the folks that tune in each week. Here is the video condensed video that gets on with it: ua-cam.com/video/DXWullu2FTk/v-deo.html I hope you're able to fix your lights!
Wasted 3 minutes of my life at the beginning. Bro spread it out thru the video. Bet you'll get more views. But thanks for making it worth me sticking around. Helped me come up with a solution. You almost lost me tho.
Boom! I just rewatched this and you're right. That's a reasonable and fair comment. I think I'll trim it up and release it as a new video to help folks get to the information more quickly. Thanks for the advice.
15 pr
I'm not certain what 15 pr means, James. But, I hope this helped you.
Why does it take you 40 minutes to get to the point. I NEED TO FI MY CHRISTMAS LIGHTS NOT HEAR YOUR SOB STORY ABOUT A SQUIRRELL CHEWING THEM. thank you.
Great point, Justine! To make it easier for everyone, I include chapters in all of my videos. That way, viewers who are short on time or just need the fix can jump straight to the relevant section. I try to create a mix of helpful tips and entertainment for those who enjoy the whole show. Thanks for watching, and Merry Christmas!
10 mins of talking for something thar took 2mins
Hello, Paul. We use the timeline chapters in this video to avoid wasting folks time. They allow you to jump right to the part you are wanting to watch.
This video was a waste of time. I've in all my years never had this particular problem with this type of light. Also, these lights are 16-22 guage wire. A lot smaller than the connector he was using for the wire. Unsafe.
That's awesome, Jimmmy, that in all your years, you've never had a single wire be severed by squirrels. Whatever you are using to keep your light strings away from wildlife...patent that! Well done you. Merry Christmas.
Who hasn't had a light string get chewed through by wildlife? Are you just putting lights on your Christmas tree and not outside your house?
Terrible advice. Never use a 10 - 12 gauge butt connector on a 16 gauge or smaller wire, no matter what you say. The only reason your wires may not have pulled out is only due to the heat shrink of the connector. A properly made electrical connection would be using the properly sized crimp connector for the wire gauge being repaired as in any and all electrical repairs. That's why there are different sized crimp connectors.
You are a cobbler, giving uninformed advice to viewers which may cause the repair to fail, and require an additional proper fix using the correct connector for the wire gauge or size being repaired.
I dare you to do a strong pull test on your crimped connection of the wires on these mini light sets with YOUR recommended 10 to 12 gauge connector BEFORE heat shrinking the connector. Because of my extensive experience with crimp connectors and how they work in both AC circuits and DC automotive circuits, I would put my money on that the connection will come apart.
Your repair only covers a broken wire. These light sets have many more common failures which are due to burnt out bulbs, burnt out bulbs with bad shunts, blown fuses and faulty bulb sockets.
To repair the most common failures of Christmas light sets, I recommend to all viewers to buy the LightKeeper Pro (for incandescent light sets) or the LED Keeper (for LED Light sets), which can be found at any Menards, Lowes, Walmart, Hobby Lobby or on Amazon. In all my years fixing Christmas lights, the only time I had a broken wire that caused the lights not to work was when animals chewed through the wire.
There are many much better UA-cam videos for Christmas light set repairs, most of which use the LightKeeper Pro or the LED Keeper.
Thanks for watching, David. I also recommend to all viewers to use Ulta-Lit's Keeper products to fix bulb and shunt issues. The Keepers are amazing products. I have several videos on those tools as well. I think you skipped the part about this cut wire being a squirrel caused issue. Squirrels do love them some Christmas lights.
lmao his guy clearly has never watched one of the videos on this channel before. Dude, figure it out before you leave an uneducated comment. Your are a cobbler of a commenter and would be better served running for congress with the other schmucks who spew asinine remarks.
Wow David woke up and decided to choose violence 🤣 wow
I spend hours fixing lights. I do have a device that finds the dead bulb for me. However I want to know how to fix strands that are torn (aka wire broken) . We have tall trees that the lights are hard to remove from and the lights get torn during the removal process. Of course the trees have 400 lights strings on them which are the most expensive. He sent why I’m watching this. Ironically have all these supplies already.
That's ironic that you mention fixing already hung lights. I had some roofline C7 greens go out on me last weekend. I had to MacGuyver a way to find the bad bulb without removing all five colors from the roof. After some thought, I came up with a super easy fix. I went to record a video on it Monday but my neighbor decided to build a new deck next to me so the noise prevented it. So, that will be forthcoming. For fixing already hung severed wires, you likely can't use a heat shrink method due to the fire hazard of the tree and danger of damaging other cords. So, you'll likely have to strip back the wire, use a wire nut, electrical tape, then duct tape. That will bring the lights back to life for the season. You can permanently fix them in the off season.