No me canso de ver el vídeo, he visto cientos de veces, estética, elegante, simple, robusta construcción, la máquina es perfecta, simplemente magnífico.
Very well executed “ project by all involved” lots of thinking went into that machine. If a fella had one he could restore a quick change gear box on anything that had sequential size and ratio gears. Well done gentlemen
I built the version from England. It was difficult and lengthy (about 240 hours). Plans were lacking in a several places as some from England are. Not enough detail. Ended up making a lot of bushings and extentions I didn't need and could had avoided with better directions. It did turn out to be a good machine though. I saw the Martin version at the NAMES show. It appeared to be a simpler design but looked very good. If I were building another I would build the Martin one. American plans are usually better. The biggest problem is finding hobs. Usually are expensive.
What a neat little machine! I thought it was made in the 40's or something, but looks as though it is a custom built unit. Thanks for showing that on UA-cam. I assume you would normally have cutting fluid all over that part, right?!
This machine is cool. So my guess is this machine makes gears? The way that worm cutting piece cuts is a lot different than a single point cutter. To have the flutes in perfect alignment to create the gear teeth is amazing.
Will it cut Helicals as well as Spur Forms? I have been looking into building a Hobber based off of one of the Barber-Coleman 16-16 as that is the type I am most familiar with. AVertica Gear Shaper based off of a Fellows wuld be a neat project too.
That's really nice. Though, if the ambition is to make gears rather than make a hobber, it might be easier to bolt a few stepper motors to a milling machine and let a computer calculate the ratios. (all depending on your personal preferences of course). (there are some examples in my channel)
Hi Jack,nice video. I don't understand how the turns between Reducer and Creator are synchronized ... do they couple with each other in some way? I tried to put a hob on the cutter to tooth a wheel, but they ate their teeth.
Is there data on this machine? I would like to repeat. If there is information please write in the comments. Есть ли данные по эму станочку, уже долго копаюсь, найти не могу. Если есть инфа накидайте пж, буду благодарен) Есть ли данные по этому станочку, уже долго копаюсь, найти не могу. Если есть инфа накидайте пж, буду благодарен)
Caro Jack Hayes ! Sou fâ desse vídeo SMALL GEAR HOBBER Coloque o meu nome na lista de interessado em comprar essa pequena máquina de fazer engrenagens . Um grande abraço Marcos !
I usually use cutting oil and with CNC you mostly need flood coolant to wash away the chips but a long time ago I took a machining class taught by a person who taught high school kids and I asked him about them not using coolant. His answer was sort of like it takes a momentous amount of energy to control these kids and can you imagine them with coolant. It gave me a sort of different perspective on coolants
Mr Glenn - why is problem location Czech republic - I am delivery machine to China - shipping cost cya 300-400 USD ))) 20 years experience with selling used machine tools
Tomas Petrzela I wasn’t aware you shipped worldwide I figured the cost would be prohibitive. Give me a qoute I’m looking to cut metric module Gears. If price is in budget I’m ready to purchase.
www.martinmodel.com/MMPtools.html Costs depend on which bits you decide you need, but the basics are about $400 I think. I also wonder about buying the set
No me canso de ver el vídeo, he visto cientos de veces, estética, elegante, simple, robusta construcción, la máquina es perfecta, simplemente magnífico.
Very well executed “ project by all involved” lots of thinking went into that machine. If a fella had one he could restore a quick change gear box on anything that had sequential size and ratio gears. Well done gentlemen
เครื่องนี้มีจำหน่ายไหมประเทศอะไร
I really like this little gear hobber and the music goes really well
Thanks for sharing that-that little machine does fabulous work-its a work of art designed by real engineers and I like your music too..
I built the version from England. It was difficult and lengthy (about 240 hours). Plans were lacking in a several places as some from England are. Not enough detail. Ended up making a lot of bushings and extentions I didn't need and could had avoided with better directions. It did turn out to be a good machine though. I saw the Martin version at the NAMES show. It appeared to be a simpler design but looked very good. If I were building another I would build the Martin one. American plans are usually better. The biggest problem is finding hobs. Usually are expensive.
Plenty of hobs available but you’re right they are expensive. Usually you only need 1-2 anyway.
@@glennedward2201 A 20 DP (diametral) pitch and a module one (metric distance between pitch in mm) will just about do it for most things.
2:35 is that cutter spindle running out or is it an optical illusion
This appears to me to be superior to another offering of castings sold in the UK. Does this also cut helical gears?
Just looking at it bring memories . but dose it cut helical gears ? very nice......
thats is so cool love it good for a small home shop ! ty do you sell the plans for it ?
Where did you get the hob cutter
Can it make helical gears?
What a neat little machine! I thought it was made in the 40's or something, but looks as though it is a custom built unit. Thanks for showing that on UA-cam. I assume you would normally have cutting fluid all over that part, right?!
very nice working by this hobber machine.well done.bravo
Please tell me if it is possible to make a splines shaft on this machine?
This machine is cool. So my guess is this machine makes gears? The way that worm cutting piece cuts is a lot different than a single point cutter. To have the flutes in perfect alignment to create the gear teeth is amazing.
Will it cut Helicals as well as Spur Forms? I have been looking into building a Hobber based off of one of the Barber-Coleman 16-16 as that is the type I am most familiar with. AVertica Gear Shaper based off of a Fellows wuld be a neat project too.
I have one machine in stock? I need for slp mexico
Gorgeous. How long did it take to put together?
Muito obrigado pelo retorno, sou brasileiro moro em Sorocaba São Paulo Brasil
Made a Jakobs. Hobber many years ago ..still got it ......
How many change gears will you need to make that stack of gears?
htral typically one for each pitch unless I’m missing something. It’s fairly basic I wouldn’t expect much for a hobby hobber.
How small gears can it make and about what is the price for such a machine?
How can I purchase this machine?
WHAT ABOUT THE HELIX ANGLE OF THE HOB????????
muito boa noite e parabens pelo video como posso ter uma maquina igual a esta ?? é possível ??
That's really nice.
Though, if the ambition is to make gears rather than make a hobber, it might be easier to bolt a few stepper motors to a milling machine and let a computer calculate the ratios. (all depending on your personal preferences of course). (there are some examples in my channel)
There are some who prefer the old ways of shop practice.
The kits come with castings premade they are affordable and will do good enough for most small shop needs.
@@12thpanzer And there are a lot of us old guys who are computer illiterate.
This machine is fit for small gear teeth cutting and how much price to make the machine
เครื่องนี้มีขายที่ไหนราคาเท่าไร
Hi Jack,nice video. I don't understand how the turns between Reducer and Creator are synchronized ... do they couple with each other in some way? I tried to put a hob on the cutter to tooth a wheel, but they ate their teeth.
um im kinda new to these stuff but how do you operate it? or program it????
Where do you buy your hobs? Are they all custom made? I have been looking for a source of hobbs for quite a while.
+Lewis Nathaniel Payton www.ebay.com/bhp/gear-hob
That was super helpful. We have started using those in class now! Thank you!
Whats the process of purchese in india
Need one ! Could you tell me the cycle time , suppose for a spur gear with Z=20 MODULE 1 MM THICKNESS 20MM
Where can I get one?
Just amazing, I love vintage machinery. Mr. Hayes, where can I find the books?
Please send the Drawings of the machine parts
How much do you want for this?
M. Maggiore xxxclm
M. Maggiore rin p
,
M. Maggiore the kits cost $500 to build your own:
www.martinmodel.com/MMPtools-subfiles/MMPtools-sub.html
Is there data on this machine? I would like to repeat. If there is information please write in the comments.
Есть ли данные по эму станочку, уже долго копаюсь, найти не могу. Если есть инфа накидайте пж, буду благодарен)
Есть ли данные по этому станочку, уже долго копаюсь, найти не могу. Если есть инфа накидайте пж, буду благодарен)
www.martinmodel.com/MMPtools.html Scroll down to the bottom of the page
Hi Jack I hope you're doing okay. Hoping you can make some more videos thank you
is there any plans for this anywhere it would make a exhalent project .
dan van der torre
Plans here:
www.martinmodel.com/MMPtools-subfiles/MMPtools-sub.html
Que maravilha, ,e eu todo me achando aqui porque criei um divisor universal no eixo (arvore lado esquerdo ) do meu torninho! parabéns .
Would love to get a hold of some plans for this
John Greiner xxxclme
I feel a great proud for some people like you! Congratulation is litlle!
Hello Jack
Greetings from Denmark. do u have drawings of the project? Best Regards - Med Venlig Hilsen. Mr.Skjoldworkshop
Do you sale The maquine?
Super 😊😊😊😊
the casting are still available
Sir' how much dirhum from UAE ? How purchasing..this machine..
Please blanck waram gear teeth waram size
So beautiful in it's simplicity..
but this one looks a bit sturdier, in the hob
and gear spindles
Sir purchase this machine
this is awesome machinery, but this is just this is done today in a mill, with a gear hobber/gear cutter and a turning table...
+Guds777 There is a big difference in gear quality, on a mill you never get an ideal gear - just some approximation.
Esta es la talladora de engranajes de Joseph Whitworth de la década de1840 mas o menos...
In México where i buy draws,mail?
Caro Jack Hayes !
Sou fâ desse vídeo SMALL GEAR HOBBER
Coloque o meu nome na lista de interessado em comprar essa pequena máquina de fazer engrenagens .
Um grande abraço Marcos !
use cnc sys , very easy to make one, no mechanical linkages required
CNC has no soul, no talent and cost prohibitive for the average person. This work of art requires thought.
make a video or how to makea little machine like that
pancho villa
The instructions and castings can be purchased here.
www.martinmodel.com/MMPtools-subfiles/MMPtools-sub.html
I should’ve built this rather than buying a Barber Coleman #3 it would’ve been easier to move around. I guess I’m going to the grave with it.
very good but without coolant ,introduce coolant system
I usually use cutting oil and with CNC you mostly need flood coolant to wash away the chips but a long time ago I took a machining class taught by a person who taught high school kids and I asked him about them not using coolant. His answer was sort of like it takes a momentous amount of energy to control these kids and can you imagine them with coolant. It gave me a sort of different perspective on coolants
one of these days im going to finish mine...
I m interested in this machine
contact me- sales@gt-machinetools.com - we have for sale gear machine WAHLI
Tomas Petrzela I’d buy it if it wasn’t located in the Czech Republic. :-(
Mr Glenn - why is problem location Czech republic - I am delivery machine to China - shipping cost cya 300-400 USD ))) 20 years experience with selling used machine tools
Tomas Petrzela I wasn’t aware you shipped worldwide I figured the cost would be prohibitive. Give me a qoute I’m looking to cut metric module Gears. If price is in budget I’m ready to purchase.
Tomas Petrzela We sent you an email inquiry.
OUTSTANDING
what is the price, where it can be buy.
only if i could buy one !
enzer191 you can! See the links in other comments. Not even expensive.
2.47 - Offenbach Barcarola
What I wouldn't do for such a machine...
Sets of castings are available.
steveastrouk where? And how much $$?
www.martinmodel.com/MMPtools.html
Costs depend on which bits you decide you need, but the basics are about $400 I think. I also wonder about buying the set
steveastrouk many thanks!
Could be much smaller with CNC
Here's how we re-sharpen those hob cutters with wire EDM
ua-cam.com/video/waRB6W0Ypmk/v-deo.html
Nice
G sir
Mozart next time..!!
magnific
jhonny granda xxxclme
جميل
ITW hob
India