You CANNOT just use the same constants if you want to go metric. I've gone through the numbers and found out why: When you divide the volume of your container with 80 you're actually BOTH converting from in3 to qt AND finding the amount of water needed: 456 in3 * 0.017316 qt/in3 * 0.72 = 5.7 qt 0.72 is the amount of water needed per amount of volume of your container. 0.017316 converts from US in3 to qt. So how did they land on the number 80? Try doing the calculation above without including the volume of your container: 0.017316 qt/in3 * 0.72 = 0.01249 ~ 0.0125 = 1/80 and 1/80 * 456 = 456/80 When using the metric system you should (I've derived these constants from the ones used in the video): Divide your volume by 1.386 OR multiply by 0.72 instead of dividing by 80. Multiply by 1.439 instead of 3 to get the amount of plaster. Remember to convert between cm3 and L: 1000cm3 = 1L ETA: Thank you for this great video!
In metric the ratio is super easy, because a liter (or cubic decimeter) of water equals a kilogram of mass, a milliliter (or cubic centimeter) is a gram. ...well and a cubic meter is a ton ofc, but i doubt there's any reason for a plaster mold that size Normally you'd just go with 7 Parts of water per 10 Parts of plaster (by weight) slight variations are usualy no concern
Because of a happy accident, I have been using canvas to dry my recycled clay. Recently I could not longer use my plater batt for drying my recycled clay (evidently used the wrong plaster); so I had to find another way to dry the clay I am recycling. I had a scrap piece of canvas laying around and found that it works well. I just lay a piece of canvas over something to allow air under it then pour the clay into it. The air evaporates the water that makes it though the canvas. There are lots of advantages of using canvas: 1) It is really cheap 2) It is easy to store (just roll it up) 3) It doesn't crack or chip or shed material 4) It scales up easily - you can use as many as you have space for 5) You can use the same piece with different clay types and not get contamination. To clean it, all you do is wash the canvas in a bucket. 6) It is super easy to move and work with. 1) To turn the clay, I put another piece on top and flip. To move it to my table to wedge, I grab the edges, flip it onto the table then peel the canvas off.
I use a large plastic dishwashing pan with a flat, smooth, unmarked bottom (this will be the side of the bat I will use). I poured water to a line inside the pan for the thickness, pour the water in a bucket, then add potter's plaster until the islands form, stir it thoroughly and pour the slurry into the dishpan. I don't do any other measurements. I can pop out the plaster bat onto a square metal pizza pan (it's a flat surface with tiny holes for air circulation that don't make marks in the soft plaster like a grate or grill can) in about two hours. It takes about a week to dry completely in a warm room. I do this with plastic bowls and containers of various sized to make hump molds, too. If you want to use both sides of the plaster bat, you can simply spray the top of the slurry in the pan with isopropyl alcohol to pop any bubbles on the surface and simply leave the plaster in the mold until it is very hard and dry to the touch, so this surface won't be as likely to chip, dent, or be scratched when you pop it out of the mold. You'll have a bat that you can flip over and use the other side once in a while, which is handy if you use different types or colors of clay and want to avoid cross-contamination or staining of a light clay with color.
Thank you for this super easy to follow video. I have used it multiple times over the last 18 months to make wedging slabs, and am about to use it again to make a damp box. :)
I've seen the wet box method and it never occurred to me to make a plaster bat like that, thank you for the easy instructions, another tip if you want to wedge and have like a plastic table is to use a small mdf board that you can rest against a wall
Great video. I did this to make a wet box for things like handles and knobs that I make in advance and keep moist for later. The lidded tub allows me to keep the plaster he moisture of the clay I'm using, and my handles will stay usable for a long time. Take off the lid though, and it sucks the moisture right out of them in minutes! Of course it does! I'll be making drying slabs this way for sure!
First of all... this made my day, so thank you! You might find that it wouldn't slip or shift on a table if you use that rubbery shelf liner stuff. I use it a lot in my workshop for various nonsense.
Thanks for the video. To anyone trying it my tip is chose the place to start carefully, don’t try to move until it’s completely dry. I think mine is cracked down middle as I made in kitchen before moving to studio. I wanted to avoid plaster in clay, as that’s a disaster
This video was/is FANTASTIC! I just made two plaster slabs; both from IRIS containers. One container is labeled a "41.2 Qt" container with dimensions of 23.625" x 17.75" and the other was labeled a "46.6 qt" container (it was taller) with dimensions of 15.75" x 19.69". The plaster set in less than 30 minutes and I was able to pop the slabs out the next morning! I love the size of the bigger one, but it is heavy. I also noticed that the thickness of the slab was 2.75" rather than the 2" I had targeted. I suspect it was because the sides of the containers were sloped outward toward the top of the container and were probably the dimensions that IRIS reported. I'm doing a new set at a reduced mixture (0.73) to see if I can hit that 2" thick mark on the nose. Thanks again, for the video. It has made my day/week/month/year!
At most home improvement stores you could also purchase a concrete mixer pan they come in 2 sizes, curved corners. After watching you video that's what I will use, but also looking at end product yours kind of has handles. Thanks
I noticed that in the video, Lindsey talks about scraping the rough surface off of the slab. Is it possible, instead, to just flip the slab over and use the smooth side for recycling/ wedging/ etc?
More plaster per water makes a less moister-wicking plaster slab. Recycling clay needs a slab made from a ratio of 2 3/4 lb. plaster to 1 quart cool to room temperature water ( don’t use hot water). Also it is necessary to have good air flow around slab when drying for increased strength.
@@syedhamzahaider512 I am no mean a expert. Lol. I think I’ll leave that for someone with more experience. 😊 I just have had a bunch of people inform me of the plaster of paris. Plus I noticed it was leaving a slight white residue when I wiped it with a sponge. So I knew it was doing the same with my clay 😐. Hopefully someone will have a answer for you soon. ✌🏽❤️
I know this was a year ago. A trick to pop the bubbles. Us a small hand torch on low and just wave across and the bubbles will pop. Learned this tip from making epoxy resin art.
this was so helpful! I also wanted to step up to something bigger but was daunted by all the construction other videos and instruction went through for a box.
Thanks for sharing this video! I did this yesterday and it came right out of the mold! It IS beautiful! I used alcohol spray but it really didn’t help all that much. 😅 Do I have to wait before it can be used?
I've been listening to your podcast so this video popped up on my feed lol I realized half way through you are the mud peddlers by your voices 😅 great video and love your podcast!
Is there an easy way to make a small vertical rim along the edge of the slab? Like maybe adding a piece of plywood just slightly smaller than the size of the container to make an indention in the main part of the slab?
Question--I have a plaster bat but the bottom is all pocked marked and uneven. Can I pour a new layer of plaster on top of it so it will be smooth again? Will the new layer bond to the plaster below it? Thanks for all your great videos!!
Ive made a wet box with plaster and rubber made tote I did it all messed up still works alright tho I want to make a plaster slab right now thanks donte and Lindsey
I was planning to pick my bag up tomorrow. I had complicated plans involving garbage bags and boxes. This is so much easier! A new cat litter pan might work well also...hmmm...
Another great video. Thank you. I saw a video on making a wet box that was very similar. If you leave the slab in the box it is basically a wet box? Very cool. Thank you.
I'm new to pottery, started using a colander(For ventilating the underside) lined with an old bed sheet, putting the slip on top of the lining, and then putting another bed sheet on top of the slip. Seemed to work pretty well and didn't need to flip the clay. ¯\_(ツ)_/¯
Just wondering, I see most people use plastic as mold. Would metal work? I wonder if I can just make a slab in a baking pan? (Sorry OCD really needs a straight side slab 😂)
I found out why you use plaster for ceramics instead of regular plaster. The builder's plaster becomes brittle and as you use it to dry clay, a film of it actually strips off and is incorporated into you clay. Not good! It absolutely ruins the clay. Makes bits just pop out of your pot days to even months after firing. Thanks for reminding us to use the right stuff!
So I made a plaster batt a couple of years ago from plaster from HomeDepot and I have never liked the batt because I keep getting plaster in my clay - now I know why. It also has gotten a gouge in it, and has cracked - even though it is in a reinforced wooden frame.
@@connecticutaggie that sux. Yeah I noticed when I used it (home depot plaster) that it did the same thing. Thankfully I didn’t ruin any pieces I had made just a bunch of clay. 🤦🏽♀️ Only then did I find this video. Better late then never I guess. 🤷🏽♀️
yup I learned this the hard way! Rather than throw out the plaster slabs I had made for clay recycling, I just lay tea towels over the plaster and dry the clay on those. It still dries the clay nicely without it having any contact with the plaster. I then wedge it on cement board. Eventually I will try again, use the right plaster and follow this video!
I am getting ready to create a ceramic-plaster bat! Thank you 2 for explaining so thoroughly and for sharing the knowledge. I had been putting off making a plaster bat because of the amount of work it takes.
Hey there thank you for the great video ! I have followed the instructions and bought pottery plaster to make one on my own. The problem is it has been 2 weeks now and it does not dry and it is a bit too soft in terms of it didn‘t harden well. I am pretty sure a i mixed it like it is supposed to be mixed 1 kg plaster with 0,7l water. I don‘t know what went wrong. Maybe you would know what could be the reason of it not drying?
Do you find you need multiple slabs for recycling light and dark clay? Or can you use the same slab (obviously not at the same time!) without too much cross contamination?
actually if you add too much plaster you can "kill" some of the plaster absorption. Remember it needs to absorbs the water from the clay, so maybe if someone thinks it's a good idea change the number to 5 or higher, maybe isn't a good idea.
I have done this but did not make it thick enough the first time what I found works best for a smooth surface is the bottom side that was against the plastic container
Hello! I have left my slab for 5-10 days in the box and whilst it popped out easily there seems to be a bit of moisture left in the plaster - i.e. i can dig my nail into it very slightly. It doesnt feel dry and crumbly, but softer. Does this mean it's not quite dry yet? I used pottery plaster. Any info would be appreciated! :) Thank you!
Found a conversion, 5.7 quarts of water is 11.89 pounds. I wanted to be able to just weigh everything out since I don't have a large pitcher with units of volume
@@EarthNationCeramics Thanks! I've done the math for larger and deeper as it is a very large form. It will sit upside in the tray on stilts for air circulation. I've been planning for months LOL.
Is it necessary to smooth down the rough side of the slab? Is that the side you will use to recycle the clay? Could you use the smooth side? On the upper rough side of the mold you mention a alcohol spray. What is the recipe for the spray? Also, do you think you could used a hand sander to knock off the rough parts?
You can if you like ( make sure to give it a few weeks to dry completely) but I use the rough side as a grip for the ground and just use the smooth side. It works well when I wedge on the floor .
I am having hard time finding potters plaster at a reasonable cost as I don’t have a store near by and with shipping it’s getting expensive. Can I use CGC Structo-Lite Basecoat Plaster ?
How did you make out with your choice and what did you finally settle on? I'm balking at the idea of using anything but potters plaster. If I hadn't read the comments here I would have been sitting here an hour from now wondering if I should take back a bag of Paris.
Great tutorial! Question: I’ve been pretty paranoid about having plaster around my clay room due to cross contamination, keeping everything separate, even mixing up outside, different buckets, etc. Am I going overboard? Thanks, Brian’s wife
Most of us buy plaster in a dried form and we mix it with water in the fashion I showed in the video and use it immediately. You should not be keeping plaster in a wet state in a bucket to the point where it gets mixed with other things. Buy the plaster, use it, keep it dried form in the original bag you bought it in. This way it is still separate and labeled while you can still make your blaster mold
Sorry if this is a silly question, but does the x80 formula still apply to metric units of measurement? I am from Australia and i can't find metric ratios anywhere for making a bat like this one.
Yes. We potters generally do not use the imperial system. We use grams. Metric is more accurate for us . Imperial Is such a bad system Even our drug dealers switched over to grams.
I understand why not to use regular plaster and stuff but would it matter if I put a moist cotton cloth in between the plaster and clay? I prefer to use a cloth sheet in between bc it’s just easier to flip the clay or carry it out in one piece and all that, but do u happen to know if it’ll keep the regular plaster residue and pieces from getting onto my clay?? Idk if you’ll know this tho.
that's what I do in my damp box and what I made for recycling clay (I agree that does make it easier to flip it) you just can't wedge on the regular plaster and it won't be as durable so you can't move it around the studio much without it being in a box or frame already.
I made this about two weeks ago and there's no way for me to release the slab from the mould haha I've tried hitting it with a hammer every day for the past week and nothing. Any tips?
I’m asking this before watching the whole video (I will, I promise), so sorry if you cover it. Could this be used in a damp box as well? Like could I have a dual purpose plaster slab? I work in a communal studio with limited space. Thank you and I’m watching the rest of the video now. Promise.
You CANNOT just use the same constants if you want to go metric. I've gone through the numbers and found out why:
When you divide the volume of your container with 80 you're actually BOTH converting from in3 to qt AND finding the amount of water needed:
456 in3 * 0.017316 qt/in3 * 0.72 = 5.7 qt
0.72 is the amount of water needed per amount of volume of your container.
0.017316 converts from US in3 to qt.
So how did they land on the number 80? Try doing the calculation above without including the volume of your container:
0.017316 qt/in3 * 0.72 = 0.01249 ~ 0.0125 = 1/80
and
1/80 * 456 = 456/80
When using the metric system you should (I've derived these constants from the ones used in the video):
Divide your volume by 1.386 OR multiply by 0.72 instead of dividing by 80.
Multiply by 1.439 instead of 3 to get the amount of plaster.
Remember to convert between cm3 and L: 1000cm3 = 1L
ETA: Thank you for this great video!
In metric the ratio is super easy, because a liter (or cubic decimeter) of water equals a kilogram of mass, a milliliter (or cubic centimeter) is a gram.
...well and a cubic meter is a ton ofc, but i doubt there's any reason for a plaster mold that size
Normally you'd just go with 7 Parts of water per 10 Parts of plaster (by weight)
slight variations are usualy no concern
Thank God for those of us that actually pay attention to math 🤓Kudos fellow mathling
You are a legend, I was trying and thinking this formula isn’t working!
Because of a happy accident, I have been using canvas to dry my recycled clay.
Recently I could not longer use my plater batt for drying my recycled clay (evidently used the wrong plaster); so I had to find another way to dry the clay I am recycling. I had a scrap piece of canvas laying around and found that it works well. I just lay a piece of canvas over something to allow air under it then pour the clay into it. The air evaporates the water that makes it though the canvas.
There are lots of advantages of using canvas:
1) It is really cheap
2) It is easy to store (just roll it up)
3) It doesn't crack or chip or shed material
4) It scales up easily - you can use as many as you have space for
5) You can use the same piece with different clay types and not get contamination. To clean it, all you do is wash the canvas in a bucket.
6) It is super easy to move and work with. 1) To turn the clay, I put another piece on top and flip. To move it to my table to wedge, I grab the edges, flip it onto the table then peel the canvas off.
What is the material you use under the canvas to allow air to circulate?
@@CookbooksonRepeat Nothing, just the finished wood of the cart or sometimes I have it on top of my old plaster batt.
Do you use the kind of canvas cloths for painting? Or which kind? I like your idea it's more beginner friendly!
@@raniachairya I bought a yard of Duck Canvas at a local fabric/craft store (Joanns)
@@connecticutaggie alrighty, thank you!!
Thanks for the shout out guys 😁👍
Finally a vid that tells me how to calculate how much plaster I'll need to make a bat. Awesome, thanks for super-helpful information !!
Yes, visual instructions! Now I can make my wedging surface! You two are awesome!
I use a large plastic dishwashing pan with a flat, smooth, unmarked bottom (this will be the side of the bat I will use). I poured water to a line inside the pan for the thickness, pour the water in a bucket, then add potter's plaster until the islands form, stir it thoroughly and pour the slurry into the dishpan. I don't do any other measurements. I can pop out the plaster bat onto a square metal pizza pan (it's a flat surface with tiny holes for air circulation that don't make marks in the soft plaster like a grate or grill can) in about two hours. It takes about a week to dry completely in a warm room. I do this with plastic bowls and containers of various sized to make hump molds, too. If you want to use both sides of the plaster bat, you can simply spray the top of the slurry in the pan with isopropyl alcohol to pop any bubbles on the surface and simply leave the plaster in the mold until it is very hard and dry to the touch, so this surface won't be as likely to chip, dent, or be scratched when you pop it out of the mold. You'll have a bat that you can flip over and use the other side once in a while, which is handy if you use different types or colors of clay and want to avoid cross-contamination or staining of a light clay with color.
Great tips- thank you.
Don’t forget to wear a respirator, plaster dust, like clay dust is not good for your lungs.
Thank you for this super easy to follow video. I have used it multiple times over the last 18 months to make wedging slabs, and am about to use it again to make a damp box. :)
Came for the info, stayed for the vibes. Thanks for putting this out into the world for newbs like me 😊
Works for me too. Relieved that the brains trust has conversion in metric.
🥰 i just made my own for reclaiming claim and a damp box following your instructions. thanks for making it easy to learn and understand.
I've seen the wet box method and it never occurred to me to make a plaster bat like that, thank you for the easy instructions, another tip if you want to wedge and have like a plastic table is to use a small mdf board that you can rest against a wall
i used those metal tray things from the dollar store that you cook in! it’s so easy and only takes a day to cure.
Great video. I did this to make a wet box for things like handles and knobs that I make in advance and keep moist for later. The lidded tub allows me to keep the plaster he moisture of the clay I'm using, and my handles will stay usable for a long time. Take off the lid though, and it sucks the moisture right out of them in minutes! Of course it does! I'll be making drying slabs this way for sure!
Is the drying box just a lidded box with plaster in the bottom? Interested in making a few.
First of all... this made my day, so thank you! You might find that it wouldn't slip or shift on a table if you use that rubbery shelf liner stuff. I use it a lot in my workshop for various nonsense.
They make good cheapo batt mates too.
Smooth the moon crater surface off with a scotch brute green scrubbier within the first couple of days . Smooth and easy
Thanks for the video. To anyone trying it my tip is chose the place to start carefully, don’t try to move until it’s completely dry. I think mine is cracked down middle as I made in kitchen before moving to studio. I wanted to avoid plaster in clay, as that’s a disaster
This video was/is FANTASTIC! I just made two plaster slabs; both from IRIS containers. One container is labeled a "41.2 Qt" container with dimensions of 23.625" x 17.75" and the other was labeled a "46.6 qt" container (it was taller) with dimensions of 15.75" x 19.69". The plaster set in less than 30 minutes and I was able to pop the slabs out the next morning! I love the size of the bigger one, but it is heavy. I also noticed that the thickness of the slab was 2.75" rather than the 2" I had targeted. I suspect it was because the sides of the containers were sloped outward toward the top of the container and were probably the dimensions that IRIS reported. I'm doing a new set at a reduced mixture (0.73) to see if I can hit that 2" thick mark on the nose. Thanks again, for the video. It has made my day/week/month/year!
At most home improvement stores you could also purchase a concrete mixer pan they come in 2 sizes, curved corners. After watching you video that's what I will use, but also looking at end product yours kind of has handles. Thanks
I noticed that in the video, Lindsey talks about scraping the rough surface off of the slab. Is it possible, instead, to just flip the slab over and use the smooth side for recycling/ wedging/ etc?
I was thinking the same thing!
wow... honestly this is going to be so much easier. I'm gonna go make myself a plaster slab this weekend!
More plaster per water makes a less moister-wicking plaster slab. Recycling clay needs a slab made from a ratio of 2 3/4 lb. plaster to 1 quart cool to room temperature water ( don’t use hot water). Also it is necessary to have good air flow around slab when drying for increased strength.
Thank you so much🙆♀️🙆♀️
Do you have a source for that correction or is that just off the dome? This would be good to know if it's true.
Thanks for this in Detail information, I made my own and it workt out just all right.🙏
Also, I'll do my own research but, metric system conversions would be nice.
do ya own research.
Lol Lindsay has got my sense of humor, seems lik a super cool chick to hang with..thanks for the video!!
I followed these directions and it was easy peasy! YAY! Thank you so much.
I legit just bought plaster to make myself a wedging table and, lo, the teacher has blessed me with instructions 😭 Thank you!
Lindsey The Monster Dillon is great in this video. Have her on more often Dante!
Thank you both for the info
Excellent! I'm a ceramics teacher and wondering how to do a cheaper way to recycle wet clay. This is perfect! Thank you so much.
Can confirm, intro footage is dope.
We use round rubber feed pans from tractor supply to put the plaster in. They work great.
Love this video, it was a great example of what is normal when just starting with clay.❤
This is fantastic, thanks! Gloves are generally recommended as plaster is hard on skin.
Making my plaster slaps to day thanks
I’ve used plaster of Paris from Home Depot with the same method and it worked well
i cant find plottery plaster in my country
i was wondering if i could use plaster of paris but does it come off and get mixed in the clay?
@@syedhamzahaider512 yes it does. It will ruin your pieces when firing. 😐
@@emilymccarthy1 so should i use a Cement block?
@@syedhamzahaider512 I am no mean a expert. Lol. I think I’ll leave that for someone with more experience. 😊 I just have had a bunch of people inform me of the plaster of paris. Plus I noticed it was leaving a slight white residue when I wiped it with a sponge. So I knew it was doing the same with my clay 😐. Hopefully someone will have a answer for you soon. ✌🏽❤️
@@emilymccarthy1 lol okay 🙂
Have a nice day 🤝
Just spray the container with Cooking spray and it releases with no need to hit with a hammer👍
I know this was a year ago. A trick to pop the bubbles. Us a small hand torch on low and just wave across and the bubbles will pop. Learned this tip from making epoxy resin art.
this was so helpful! I also wanted to step up to something bigger but was daunted by all the construction other videos and instruction went through for a box.
Great video! I just made my second plaster slab using this method.
I totally did this. It's currently setting up.
Nice thing about this is you can pop it back in for a damp cabinet!
Thank you Lindsey and Dante's hands.
Dante's special pottery and video making talking hands
Thanks for sharing this video! I did this yesterday and it came right out of the mold! It IS beautiful! I used alcohol spray but it really didn’t help all that much. 😅
Do I have to wait before it can be used?
This was soooo helpful. Wish I had watched it before I made three huge drying slabs out of regular plaster.
I've been listening to your podcast so this video popped up on my feed lol I realized half way through you are the mud peddlers by your voices 😅 great video and love your podcast!
Thanks for this reminder! I just made up a plaster slab!! :D
With the shape of the slab, it's actually very easy to secure it to fx. a table; for the wedging part ☺️
Is there an easy way to make a small vertical rim along the edge of the slab? Like maybe adding a piece of plywood just slightly smaller than the size of the container to make an indention in the main part of the slab?
terrific video - thank you very much
Love it! Thank you so much guys
Question--I have a plaster bat but the bottom is all pocked marked and uneven. Can I pour a new layer of plaster on top of it so it will be smooth again? Will the new layer bond to the plaster below it? Thanks for all your great videos!!
Ive made a wet box with plaster and rubber made tote I did it all messed up still works alright tho I want to make a plaster slab right now thanks donte and Lindsey
I’ve seen this also do double duty as a damp box too!
cool vid. Did you use a mold release, or does it just pop out?
Great video! It was super helpful.
You always seem to time your videos on point to what I'm planning to do in the next couple weeks. I just bought a 50lb bag of plaster. LOL
I was planning to pick my bag up tomorrow. I had complicated plans involving garbage bags and boxes. This is so much easier! A new cat litter pan might work well also...hmmm...
Can u do a video on how to make a longer slab? But thinner. Yea she's great. I saw her video on the slab.
Thank you! I will definitely use this method.✅
Another great video. Thank you. I saw a video on making a wet box that was very similar. If you leave the slab in the box it is basically a wet box? Very cool. Thank you.
I'm new to pottery, started using a colander(For ventilating the underside) lined with an old bed sheet, putting the slip on top of the lining, and then putting another bed sheet on top of the slip. Seemed to work pretty well and didn't need to flip the clay. ¯\_(ツ)_/¯
This tutorial is exactly what I was needing! Loving the podcast too!
Just wondering, I see most people use plastic as mold. Would metal work? I wonder if I can just make a slab in a baking pan? (Sorry OCD really needs a straight side slab 😂)
Love this! Was just thinking about this
I found out why you use plaster for ceramics instead of regular plaster. The builder's plaster becomes brittle and as you use it to dry clay, a film of it actually strips off and is incorporated into you clay. Not good! It absolutely ruins the clay. Makes bits just pop out of your pot days to even months after firing. Thanks for reminding us to use the right stuff!
So I made a plaster batt a couple of years ago from plaster from HomeDepot and I have never liked the batt because I keep getting plaster in my clay - now I know why. It also has gotten a gouge in it, and has cracked - even though it is in a reinforced wooden frame.
@@connecticutaggie that sux. Yeah I noticed when I used it (home depot plaster) that it did the same thing. Thankfully I didn’t ruin any pieces I had made just a bunch of clay. 🤦🏽♀️ Only then did I find this video. Better late then never I guess. 🤷🏽♀️
yup I learned this the hard way! Rather than throw out the plaster slabs I had made for clay recycling, I just lay tea towels over the plaster and dry the clay on those. It still dries the clay nicely without it having any contact with the plaster. I then wedge it on cement board. Eventually I will try again, use the right plaster and follow this video!
I am getting ready to create a ceramic-plaster bat! Thank you 2 for explaining so thoroughly and for sharing the knowledge. I had been putting off making a plaster bat because of the amount of work it takes.
Hey there thank you for the great video ! I have followed the instructions and bought pottery plaster to make one on my own. The problem is it has been 2 weeks now and it does not dry and it is a bit too soft in terms of it didn‘t harden well. I am pretty sure a i mixed it like it is supposed to be mixed 1 kg plaster with 0,7l water. I don‘t know what went wrong. Maybe you would know what could be the reason of it not drying?
How thin can it be? Wondering if it would crack if I made it 1" or 1.5". Thanks!
Try a palm sander or something that doesn't vibrate too violently against sides and underneath to release any air bubbles.
Do you find you need multiple slabs for recycling light and dark clay? Or can you use the same slab (obviously not at the same time!) without too much cross contamination?
do u think it would be possible to use this method + coating with a sealant to create a table(coffee table)? will it be durable? tia.
actually if you add too much plaster you can "kill" some of the plaster absorption.
Remember it needs to absorbs the water from the clay, so maybe if someone thinks it's a good idea change the number to 5 or higher, maybe isn't a good idea.
If you smear a very light coat of vegetable or olive oil with a paper towel it works wonders
Hi, new Potter here. Which of the two sides should I use? The smooth one or the side of the moon one? Does it matter?
I have done this but did not make it thick enough the first time what I found works best for a smooth surface is the bottom side that was against the plastic container
Fo sho. I usually flip mine over to a smurther surface.
@@EarthNationCeramics also, I've found it more effective if the plaster has airflow underneath. I.E. mine is on a metal shelf with slats.
Hello! I have left my slab for 5-10 days in the box and whilst it popped out easily there seems to be a bit of moisture left in the plaster - i.e. i can dig my nail into it very slightly. It doesnt feel dry and crumbly, but softer. Does this mean it's not quite dry yet? I used pottery plaster. Any info would be appreciated! :) Thank you!
Would cement board work to recycle clay on??
Yeah but nowhere near as well.
Thank you both!
Was Lindsey flicking everyone off during math jam
Found a conversion, 5.7 quarts of water is 11.89 pounds. I wanted to be able to just weigh everything out since I don't have a large pitcher with units of volume
5-gallon buckets are handy in moments like this, especially if they're semi-transparent and have graduated measurements on the outside.
Are there any updates about the plaster availability? Looks like Amaco no longer makes the product. Most stores I’ve found run $100 for 50lbs.
Could you set a mold (like a plate) into this type of ratio for slip casting?
Thanks for sharing your tips. Pottery plaster is not available in my country (Malta). Can I use plaster of Paris instead please? Much appreciated.
I also had this question? Did anyone answer you
Does Perfect Plaster work as well?
I have a large deep stainless steel tray. Will the plaster pop out of this mold or must I use a plastic container?
yeah it just wouldnt be as deep. i aim for 2" deep
@@EarthNationCeramics Thanks! I've done the math for larger and deeper as it is a very large form. It will sit upside in the tray on stilts for air circulation. I've been planning for months LOL.
Nice! Thanks!!
Is it necessary to smooth down the rough side of the slab? Is that the side you will use to recycle the clay? Could you use the smooth side? On the upper rough side of the mold you mention a alcohol spray. What is the recipe for the spray? Also, do you think you could used a hand sander to knock off the rough parts?
You can if you like ( make sure to give it a few weeks to dry completely) but I use the rough side as a grip for the ground and just use the smooth side. It works well when I wedge on the floor .
I am having hard time finding potters plaster at a reasonable cost as I don’t have a store near by and with shipping it’s getting expensive. Can I use CGC Structo-Lite Basecoat Plaster ?
How did you make out with your choice and what did you finally settle on? I'm balking at the idea of using anything but potters plaster. If I hadn't read the comments here I would have been sitting here an hour from now wondering if I should take back a bag of Paris.
USG #1
Video on making a plaster of Paris wedging table….?
Can I use plaster of Paris? Is that the same thing as pottery plaster?
Great tutorial! Question: I’ve been pretty paranoid about having plaster around my clay room due to cross contamination, keeping everything separate, even mixing up outside, different buckets, etc. Am I going overboard? Thanks, Brian’s wife
Most of us buy plaster in a dried form and we mix it with water in the fashion I showed in the video and use it immediately.
You should not be keeping plaster in a wet state in a bucket to the point where it gets mixed with other things.
Buy the plaster, use it, keep it dried form in the original bag you bought it in. This way it is still separate and labeled while you can still make your blaster mold
Sorry if this is a silly question, but does the x80 formula still apply to metric units of measurement? I am from Australia and i can't find metric ratios anywhere for making a bat like this one.
Yes. We potters generally do not use the imperial system. We use grams. Metric is more accurate for us .
Imperial Is such a bad system Even our drug dealers switched over to grams.
I am from Australia too but I ended up converting to imperial just to make sure I got it right.
Yes, you’re right, I needed this information!
I understand why not to use regular plaster and stuff but would it matter if I put a moist cotton cloth in between the plaster and clay? I prefer to use a cloth sheet in between bc it’s just easier to flip the clay or carry it out in one piece and all that, but do u happen to know if it’ll keep the regular plaster residue and pieces from getting onto my clay?? Idk if you’ll know this tho.
that's what I do in my damp box and what I made for recycling clay (I agree that does make it easier to flip it) you just can't wedge on the regular plaster and it won't be as durable so you can't move it around the studio much without it being in a box or frame already.
I made this about two weeks ago and there's no way for me to release the slab from the mould haha I've tried hitting it with a hammer every day for the past week and nothing. Any tips?
Is casting plaster the same as pottery plaster?
What's the difference between normal plaster and pottery plaster?
I’m asking this before watching the whole video (I will, I promise), so sorry if you cover it. Could this be used in a damp box as well? Like could I have a dual purpose plaster slab? I work in a communal studio with limited space. Thank you and I’m watching the rest of the video now. Promise.
Yes but in my experience that has a habit of growing mold
Lindsey looks just like Michelle Dockery.
Thank you... but wait I thought plaster was caustic for your hands (?)
Thanks for doing this! I
Is that bin really only 12x19 inches? It looks way bigger.
Got it Wants! 🤗