See the milling of spur-toothed bevel gears on a amateur milling machine. The presented procedure is time-consuming but works fine in the home workshop. #lscad
Brilliant demonstration of the method described in Ivan Law’s book. I’m just about to try it on my Myford Super 7 lathe, with the Myford dividing attachment . . . . Kind regards, Steve A.
Vielen Dank! Ich bin Brasilianer. Das Video ist ausgezeichnet und beschreibt ein Thema, das nur erfahrenen Maschinisten vorbehalten ist. Ich hatte es bereits aus dem Deutschen übersetzt, aber ich habe es einfacher als Englisch.
I too prefer the sound of the machine some of the other comments I don't even know where to begin other than somebody didn't have anything better to do human beings are a petty worthless lot to begin with those with the least intelligence or the most intelligence often make the most trouble especially if they have no practical experience. Sometimes it's best to know only enough to be motivated and productive that's where the most fun can be found. Learning comes from making it over because of some minor detail you are not aware of and therefore overlooked.
@@prof-rieg I'm strugling with this formulas... Can you help? The question is i need a bevel gear for 2 shafts at 90º transmission. I found at Aliexpress a bevel gear that is advertised as 15T M0.8. And here starts the problem. By the formula you use "d" should be 12mm (0.8x15=12), but is not. Also "dai" by formula should be 13.13mm, but is only 8.41mm. Also "daa" should be 20.13mm (for "b=3mm), but is only 13.13mm. What am i missing? I bought from Aliexpress this bevel gear and they work very smooth, but unfortunately they are not hardened and i would like to do by my own same gears and then do some heat treatment to make them hard. I already tried but i can't make them so smooth as the original one. At Aliexpress the seller have a draw. If you could take a look and give some help i would aprecciate a lot. Here is the link to the bevel gears: www.aliexpress.com/item/1005005119203188.html?spm=a2g0o.cart.0.0.55bc38daDI7KNO&mp=1 Thank you for your attention and also for this great lesson!
Going from zero to plus five and then to zero and finally minus 5 I did not notice you making up for the play in the dividing head is that just me not seeing what you did or please explain.
Great video but not any easy work for an amateur. Just built and verified a digitally controlled rotating table having a resolution of 2.25 seconds. Cutting gears are waiting. The question is what kind of gears there are....
Sorry, this is too difficult for an amateur shop. This needs highly sophisticated gear cutting machines, i.e. American Gleason machines or German Klingelnberg machines.
Brilliant demonstration of the method described in Ivan Law’s book.
I’m just about to try it on my Myford Super 7 lathe, with the Myford dividing attachment . . . .
Kind regards,
Steve A.
Thanks a lot and good luck!
New subscribed from Somalia thanks
Thank you very much! And greetings to Somalia!
This was an amazingly informative video about bevel gear machining on manual machines. Thank You for showing this operation. From Alaska, USA
Thank you very much. Greeting to Alaska from Germany!
The best video and detailed and easy to understand. Thanks LSCAD for sharing. Very much appreciated. Your subscriber from the Philippines. More power.
Thank you very much!
And a lovely little Myford!!! Great video! I have to make a pair for my 1/3 scale mill engine!
Thanks a lot!
perfect work,regards from Greece!
Thank you and greetings to Greece!
Great video. Loved all the closeup shots. Just subscribed :)
Thank you very much - you are welcome!
Great video, very well explained. Thank you!
Thank you, very kind of you!
Vielen Dank! Ich bin Brasilianer. Das Video ist ausgezeichnet und beschreibt ein Thema, das nur erfahrenen Maschinisten vorbehalten ist. Ich hatte es bereits aus dem Deutschen übersetzt, aber ich habe es einfacher als Englisch.
Vielen Dank fuer Ihre Rueckmeldung und Gruesse nach Brasilien!
Great video, well explained, nice work
Thank you very much!
I have a Stuart Sirius kit that has a bevel gear. Never got time to build it so it's collecting dust. Nice work on the Number 1 Stuart!
Thank you!
Thank you for the lesson!
Thank you for your comment!
Great video,thanks a lot.
You are welcome!
Great work I'll have to try it. Subscribed
Thank you - you are welcome!
Realy good video!
Thank you very much!
very good video..thanks for your time
Thank you very much!
thank you very helpful
You are welcome!
Thanks for tips
you are welcome!
Excelent video
Thank you very much!
Great work.. Can I make a 23 tooth gear differentially without using the number 23 or its multiples?
Thank you very much! Yes, please see my video #195.
If you show me how to machine hypoid gears in a manual mill I'll be forever grateful!
I too prefer the sound of the machine some of the other comments I don't even know where to begin other than somebody didn't have anything better to do human beings are a petty worthless lot to begin with those with the least intelligence or the most intelligence often make the most trouble especially if they have no practical experience.
Sometimes it's best to know only enough to be motivated and productive that's where the most fun can be found.
Learning comes from making it over because of some minor detail you are not aware of and therefore overlooked.
Thank you very much for your feedback!
Gear cutting karne mai problem hai to help milegi kya sir...?
Thanks for sharing. But this are no bevel gears…
Hi, is this method also good to do small bevel gears? Example: daa= 13mm and M0.8 cutter? Thank you
@@paulosoarescarvalho6219 yes, I guess so
@@prof-rieg I'm strugling with this formulas... Can you help? The question is i need a bevel gear for 2 shafts at 90º transmission. I found at Aliexpress a bevel gear that is advertised as 15T M0.8. And here starts the problem. By the formula you use "d" should be 12mm (0.8x15=12), but is not. Also "dai" by formula should be 13.13mm, but is only 8.41mm. Also "daa" should be 20.13mm (for "b=3mm), but is only 13.13mm. What am i missing? I bought from Aliexpress this bevel gear and they work very smooth, but unfortunately they are not hardened and i would like to do by my own same gears and then do some heat treatment to make them hard. I already tried but i can't make them so smooth as the original one. At Aliexpress the seller have a draw. If you could take a look and give some help i would aprecciate a lot. Here is the link to the bevel gears: www.aliexpress.com/item/1005005119203188.html?spm=a2g0o.cart.0.0.55bc38daDI7KNO&mp=1
Thank you for your attention and also for this great lesson!
Is there any portal that people can donate to your channel?
No, it's all free.
@@prof-rieg your humanity is immeasurable..keep going Sir the world need to learn.
@@Mewanrahnam575 Thank you very much!
Going from zero to plus five and then to zero and finally minus 5 I did not notice you making up for the play in the dividing head is that just me not seeing what you did or please explain.
The play of the diving head caused no problem.
1:52 Can you pls tell me the name of background music?
It is mentioned in the beginning of the video.
Great video but not any easy work for an amateur.
Just built and verified a digitally controlled rotating table having a resolution of 2.25 seconds. Cutting gears are waiting. The question is what kind of gears there are....
Thank you very much and good luck for your bevel gears!
Pls cutt spiral bevel gear
Sorry, this is too difficult for an amateur shop. This needs highly sophisticated gear cutting machines, i.e. American Gleason machines or German Klingelnberg machines.
Are you have email or contact sir
yes: frank.rieg@uni-bayreuth.de
Can't the crap music, I'd rather hear the machine like any machinist would comment; this says most about what is happening!
Music, loosely called, is atrocious! Very distracting, even hateful.