Mine was working fine, then I had to replace a breaker in the system. When I powered things back up, I must have connected the panels first, then the battery. I heard something, which turned out to be the two 30a fuses. Thank you for posting or I would probably have scrapped it and started over. I'm a tad surprised that the fuses were soldered? in! I added remote fuse holders as you did and everything is good again. Thanks again for posting!
I asked for a line with the output of the temperature meter with a positive line of solar energy and the device stopped working and the display of the meter meter mt50 is in contact and comment on it is there a possibility to repair it thanks
I have a 20amp tracer that shows battery as not charging and a 12v battery voltage reading on the charge controller reads 45v. Plugging the battery on a multi meter reads 12.8 volts and the inverter doesn't complain about over voltage. What could be the cause?
Good idea to pop some fuse carriers in, but try to keep the cable length both short and the same length for each one to ensure the fuses carry equal load. To blow 60 amps of fusing (which will probably carry 80amps for a bit) something has gone a bit wrong. Was this fused or connected to a breaker externally?
I shortened the longer cable to match the other shorter one, was a bit tricky to fit the fuse holders in there. I really don't know what went wrong, I did have a breaker in the line. I think I'll only run one panel on it now, just in case. I'm setting up a new 12v system. Stay tuned😁 Thanks Adam ☺
Never run these at their max rated voltage. I found ~75pvdc to be their limit. They work best when you use multiple chargers rather than 1 big one. So like 1 for every 2-3 solar panels.
Mine still powers but not charging. Changed a diode it worked for another 2 weeks and now, Diode is ok, powers is on but not charging. Now it's confusing.
Hmm, so any idea what blew the fuses or what is connected behind them? Could be something on the load side that shorted maybe? If not, it might break on you again when you start connecting the solar panels and/or load to it.. Cool system you got there anyway :). And nice to hear some of the birds in the background too haha. Gives it a nice vibe.
I am really not sure what made them blow. I'll be keeping a close eye on it when I set it up again! I'll be using less solar as well. Thanks for the positive comment 😊 We have a lot of birds where I live, they make a great soundtrack, glad you enjoyed them.
Hi there, how was it getting the fuse out? Looked at mine, the fuse seems flush with the board and no way of accessing it from underneath. Hoping to change the fuse as it's blown, please help!!
Hi From memory it wasn't that close to the board on mine. Can you get some small snips in there? If not you may need to desolder from back of board and add some short pieces of wire then fuse. Good luck
i have a problem with the mppt epever tracer controller, the problem is the screen on the lcd has no indicator image but the lcd screen light remains on, is there a solution to fix it, thanks
@@offgriddreaming5403 thank you for that information. I had a Renogy charge controller with the same issue. It was almost impossible for a mortal like myself to get to the fuses. At least this one has access.
You mentioned it was working fine, then you setup your 48v system, and plugged it back in. Are you implying that you plugged this into a 48v battery? If so that was you problem. The 30a tracers only do up to 24v
Mine was working fine, then I had to replace a breaker in the system. When I powered things back up, I must have connected the panels first, then the battery. I heard something, which turned out to be the two 30a fuses. Thank you for posting or I would probably have scrapped it and started over. I'm a tad surprised that the fuses were soldered? in! I added remote fuse holders as you did and everything is good again. Thanks again for posting!
I'm glad it helped!
Good work man 👍
Thanks 😀
Nice Save!!!
Thanks mate 😎
Nice one mate
Thanks buddy
I have one of this, it just went bad early this year. I really hope I could fix it. Can you help guide me through?
I asked for a line with the output of the temperature meter with a positive line of solar energy and the device stopped working and the display of the meter meter mt50 is in contact and comment on it is there a possibility to repair it thanks
I have a 20amp tracer that shows battery as not charging and a 12v battery voltage reading on the charge controller reads 45v. Plugging the battery on a multi meter reads 12.8 volts and the inverter doesn't complain about over voltage. What could be the cause?
Good idea to pop some fuse carriers in, but try to keep the cable length both short and the same length for each one to ensure the fuses carry equal load. To blow 60 amps of fusing (which will probably carry 80amps for a bit) something has gone a bit wrong. Was this fused or connected to a breaker externally?
I shortened the longer cable to match the other shorter one, was a bit tricky to fit the fuse holders in there.
I really don't know what went wrong, I did have a breaker in the line. I think I'll only run one panel on it now, just in case.
I'm setting up a new 12v system.
Stay tuned😁
Thanks Adam ☺
Never run these at their max rated voltage. I found ~75pvdc to be their limit. They work best when you use multiple chargers rather than 1 big one. So like 1 for every 2-3 solar panels.
Thanks for the tip!
Mine still powers but not charging. Changed a diode it worked for another 2 weeks and now, Diode is ok, powers is on but not charging. Now it's confusing.
Ello Oku yes that sounds weird.
Maybe a fault with the circuit board?
Hope you can sort it out.
Hi dear i have a same model but bot working can you repair it for me
Hmm, so any idea what blew the fuses or what is connected behind them? Could be something on the load side that shorted maybe? If not, it might break on you again when you start connecting the solar panels and/or load to it.. Cool system you got there anyway :). And nice to hear some of the birds in the background too haha. Gives it a nice vibe.
I am really not sure what made them blow. I'll be keeping a close eye on it when I set it up again! I'll be using less solar as well.
Thanks for the positive comment 😊
We have a lot of birds where I live, they make a great soundtrack, glad you enjoyed them.
Hi there, how was it getting the fuse out? Looked at mine, the fuse seems flush with the board and no way of accessing it from underneath. Hoping to change the fuse as it's blown, please help!!
Hi
From memory it wasn't that close to the board on mine.
Can you get some small snips in there? If not you may need to desolder from back of board and add some short pieces of wire then fuse.
Good luck
Broke mine do you know where I can get the LCD display component ?
Jak Dac Hi
I don’t sorry. I would try your loacal distributor or epever
Mt150
Need to replace the green blocks ! Does anyone know where to buy them?
I'd try Aliexpress
i have a problem with the mppt epever tracer controller, the problem is the screen on the lcd has no indicator image but the lcd screen light remains on, is there a solution to fix it, thanks
Hi
I would contact epever and see if they have a replacement lcd module.
Pls tell me inductor veliue...uh
Can I use any 12 volt spade fuse holder of the correct amps? Ours is a 40 amp Tracer charge controller and I know I blew the fuse.
Hi
Should be fine. That's what I used ✌
@@offgriddreaming5403 thank you for that information. I had a Renogy charge controller with the same issue. It was almost impossible for a mortal like myself to get to the fuses. At least this one has access.
@@asthewheelsturnrv8624
You're welcome
@@asthewheelsturnrv8624 Did you manage to get the fuse off? Having the same problem at the moment. Can't believe it's soldered in! Cheeers
@@joesnow739 I did get the fuse off but that wasn’t the issue so I ended up buying a Renogy Rover. I’m not very good at soldering.
Mine connects to solar for 2 seconds then disconnects! Over and over, dont know whats wrong.
Have you contacted the seller? Not sure what would cause that
I have the same problem with an Epever 60 amp mppt
Your pv is to high. If you're running it at 100v, stop, run them at Max 75pvdc.
You mentioned it was working fine, then you setup your 48v system, and plugged it back in. Are you implying that you plugged this into a 48v battery? If so that was you problem. The 30a tracers only do up to 24v
No, only ever used this for 12 volt.
Referring to separate 48v system
@@offgriddreaming5403 Ahh. Got ya
Mine just went off no display and is not showing anything
You could check the fuses inside
So you just replaced fuses.
Artjoms Pugacovs Correct ✌🏼
Myne smelled like burned plastic after 14 months use.