Top 3 Mini UPS for WiFi Router | 12V Mini UPS | Router UPS for Work for Home
Вставка
- Опубліковано 27 лис 2024
- #MiniUPS #UPSforWiFIRouter #UPSforWorkFromHome
In this video, I will share all the 3 versions of my Mini UPS for WiFi Router. This little gadget is really helpful for this work-from-home time.
Mini UPS V1.0
Mini UPS V2.0
Mini UPS V3.0
Instructables link: www.instructab...
Download the.STL file: www.thingivers...
Download the Schematic: bit.ly/2I4wg4H
Instagram id link: / opengreenenergy
Disclaimer:
------------------
I cannot be held responsible for any loss of property, damage, or loss of life if it comes to that. This tutorial was written for those who have knowledge of rechargeable lithium-ion technology. Please do not attempt this if you are a novice. Stay Safe.
**************************************************************************
Parts Used:
Components Required :
1. TP5100 Charger : amzn.to/3jMyGDc
2. Boost Converter : amzn.to/33P8AtP
3. LEDs : amzn.to/2GSzHuC
4. DC Jack- Female :amzn.to/2FYZEG5 / www.banggood.i...
5. DC Jack-Male: amzn.to/2FOhuu5 / www.banggood.i...
6. Rocker Switch: amzn.to/2HVo1Xv / www.banggood.i...
7. 18650 Battery: www.banggood.i...
8. 2S BMS: amzn.to/3dgvixG
9. Double-sided tape: amzn.to/3df3REA
10. Electrical Tape: amzn.to/2GLD2M9 / amzn.to/3lxHNrY
11. Volt Meter: amzn.to/3nAWewT
12. 20 AWG Wires: amzn.to/3iEYuQg/ www.banggood.i...
13. Heat Shrink Tube: amzn.to/2HZjC5G / www.banggood.i...
14. XL6019 Boost Converter: amzn.to/34zJ62o
15. 1N5822 Diode: amzn.to/2GOQRJK
Nice mini ups backup..
hey it is posible to charge and supply energy at same time?
This the best video yet , checked many here of ups for router, marked improvement form the earlier videos : THERE IS A FLAW ?? 1). the battery will not stop charging, when full, there is no relay to stop or start charging ( hence NO PROTECTION) 2). There should be auto changeover to battery incase of power failure. how will you pls incorporate into the circuit, is possible to put all this into one single pcb ...thanks of
Can I use 2 XL6019 if I want to have two 12v output? Or just split two dc jacks from one XL6019?
Use two XL6019
@@opengreenenergy how increasing the 18650 battery? 2S 5P 2600mah? Should I increase the amperage of the dc buck stepdown supply? By how much?
Sir can you please make a small inverter for laptop charger which will work for approx 4-5 hrs using solar panel or battery
Great build. Is it possible to add modification for using a LiFePO4 battery and atleast 3amp - 12v output?
Yes
Sir plz reply
BMS protect battery from overcharge then is it necessary to use tp5100 module..?
Yes, TP 5100 is for charging
what do i need to change or add to have a 5v output. my router uses 5vdc. Thanks it is a great job.
you need an step down adjusted to 5v
What is the best configuration for 12V battery, 2S, 3S or 4S. even at cut off voltage at 3.0V, 4S gives 12V. Appreciate your view. Thank you.
Yeah you are correct
Very nice bro
Excellent.
Thank you
How long The UPS can suply for Router sir?
How could i connect a d1 mini to send a notification if the main power goes out (and therefore the router is running on batteries)? Thanks and great job 👏👏
What should I change to the V3 to get more backup backup? Also, would like to get my UPS charged with a 12v 3w mini solar panel, is this possible?
Make sure the voltage of the XL6019 is set to be less than the voltage of the input 12v adapter, otherwise the current will not flow across the bypass. Instead it wall always flow through the XL4015 and XL6019 even when AC adapter is providing power.
Bro just use a 3s battery
what alternative for In5822, any suggestion?
Any 58 series diode
could you use a LM2596 in place of XL6019 thank you for you videos
Can use lifep04 battery in this same circuit. Replacing of lithium-ion cell
Nice work thanks for sharing
Sir I have two doubts please reply. I ordered everything and waiting for your reply.
1. My router is of 1.5ampere should I tune the buck converter to 1.5 ampere instead of 2 ampere.
2. I have wifi router charger using which I tried to tune the buck converter and I am able to set the volts to 8.36 but when I tried to set the amperes I'm not receiving enough amperes from wifi charger it's not crossing 1 ampere also. In this case for setting the ampere should I purchase another charger of 12v /3 ampere or can I use the same wifi charger of 12v/ 1.5 ampere charger.
Thank you Sir
1. No need to change the buck converter current setting.
2. Need a separate charger 12V / 3A
Bro kitna hour’s ka backup de ga ??
hi!!!!! I would do anything like your ups ,but i' need in the output 2,5 amp for the router and 3 amps for a mini pc (web server) at 12v both but their real wattage rarely exceds 30W and they are normally at 20w . i'm think that uses BMS 3S (3x(2 or maybe 3 CELL 3000mah ) searching an autonomy of 3h ) and i have 3 xl 4015
It's possible that apply your 2X2 model changing the xl 6019 at the output by one xl 4015 at 12V@3A to serve both devices? or two xl 4015 one for router at 2,5 A an another for minipc at 3A??
The XL 4015 at the input what is the high Amperes that i can put for fast charge and ? the power source its the source of minipc 12V at 3A
it's factible? or it's a pre-tragedy?😅 i'm a newbie
Thanks for advance and congrats for your videos!
what is the efficiency level of your ups?
Fristt brooo
why not using 3s bms ? so no need the boost converter to set 12v output ?
Yes, bms 2s is useless for me doesnt work, many trouble, i used bms 3s for ups router, bms 2s is not recomended
You shoud connect relay for long backup
Do you make v3 for selling?
Amazing
What is the purpose of the voltmeter , the bms will ensure the battery is at optimum voltage so how will it help to know the battery voltage , I would suggest an LED indicator and buzzer combo to indicate a low battery
Thank you for your feedback. I will probably consider it in my future versions.
Voltmeters shows battery voltage, hence the SOC (State Of Charge) can be known. BMS does NOT do battery level indication.
Want to order an UPS for WiFi router with extended backup. Please let know, how to order ?.
Good hit 🇮🇳👍👍👍 Kuki
Hello..... In version 2.0 of router u missed to display tp5100 set for output for 7.4v charging
can I Use XL6009?
I don't understand why you didn't use a battery holder. That also bypasses doing anything to the batteries, and makes it to where you can swap out the batteries...
Sir can i use 1n4007 diode
No it is not recommended, use schotkey diode
@@opengreenenergythanks
Can two routers be connected to it? if possible what should be changed?
Yes
I started to make it . I founded that no voltage on P+ & P- terminal of the BMS . Plz clarify if any mistake . Thanking you.
BMS board are factory locked. Connect to a power source first, then it will be unlocked and you will see the voltage. It is required only once
@@opengreenenergy
Thank you very much. Power means the charging voltage i.e. 8.35 V @ 2 amp current from the XL 4015 board module connection with the li-on batteries ?
Yes, connect it to the xl4015 output
@@opengreenenergy
Thank you . I will complete the connections .
The connection is completed and it works perfectly . Again thank you very much for supporting me . I'm a great follower of your projects .
5:35 Mini Ups v2.0
I have 12v 0.5A modem and 12v 0.5A Router. How can i use these two devices simultaneously with Mini UPS V3.0 ????????
Connect two dc jacks at the output of the boost converter.
@@opengreenenergy what about input i have 2 12v 0.5A adapter so if i am connecting 2 device with 12v 0.5A should i use 12v 1A charger or higher ??? instead of 12v 0.5A???
@@myinfobeam7882 yes bro
If you off the switch, the current from battery will flow to +ve of xl4015 output then to input wire then to 12v output. You need to modify the switch connection.
noo
Sir will the cost of making this project?
BTW great work 👏🏻
Most of the components probably cost less than 20-30 bucks...minus those batteries...you can use recycled but they are not as good as those he used
₹1450 if you have all the equipment at hand (like soldering iron wires etc)
10:20 satisfaction
14:40 I would put a switch between the battery and the main circuit.
Otherwise, it is not logical, since there will be no fully UPC and it is not clear what.
In version 3.0 you have added a diode in the output of xl6019 and connected that with the input positive diode of xl4015 why pls say the reason
I was thinking to prevent power from the adapter from flowing to the output side of the xl6019 and to prevent power from the xl6019 from returning to the adapter.
Can you please tell me circuit for 12v battery. Like if I want to use 12v battery instead of these 18650 cells
12v bike battery you can say
Hi can you give training to make ups and power bank
good
Why not using 3s of 18650 instead, wtih 3s BMS. Then you don't need boost converter. You can connect 12v power to BMS, parallel to 12v out for supplying the load. This way, when the power from line is on, it will supply power for the load but in parallel charge the battery through bms. When power is off, the battery will take over because it is connected in parallel with 12v out via BMS.
Thank you for your suggestion.The problem in when we will not use the boost converter is that, the Router will not work when battery pack gets discharged to a certain level. That means we will not able to use the full capacity of the battery pack.
@@opengreenenergy ah, I got your point. The boost converter is to ensure the Router is fed with a stable 12v. Thanks!
Hello , can you provide me enclosure on chargeable basis
what is difference between all 3 of them ??
In short, battery capacity and size. The first one is a 1-cell design, the second is a 2-cell design, and the last one is a 4-cell design.
please let us know how to implement Over charge protection for this UPS, I want to always keep connected 12V adaptor , and do not want to remove the 12V adaptor form this setup !
I am using the V3.0 from the last lockdown, always plug in to supply. No problem still now.
The 2S BMS (battery management system) handles the overcharge/overdischarge voltage...plus it keeps the batteries balanced
The batteries he used also have battery protection circuits already on them (they are a little longer than unprotected 18650's)
Kimalt, batov ,odar, nabar ,,bata v
How long battery backup, for first UPS
Then, put it on 24x7. I.e. charging + using when there is power. It should switch to auto when there is no power. Any idea
@@NEONBOXYT it will switch automatic when power goes off
Plz tell where to buy the components
hello sir what is value of fused you used in version 3 ups
5A
Sir, power Bank ko micro inverter kese banaye ?
sir can you make a solar clock?
Helloi admin,
Can you make our existing circuit with solar power with normal electricity charger also.
Case1 : when sun is there powerbank will run on solar pannel
Case 2 : when sun is not there or low solar power it will shift to 12volt adapter power
Case 3 : when solar and adapter power is absent it will shift to charged batteries.
Everything should be automatic.
Can we create a power back of 4-5,hrs for a 24inch monitor, cooling pad and may be able to charge a laptop, to be applicable in off-road/off-grid scenarios
Can I get this product
👌👌👌👌
why should i use TP 5100 ?
For charging the 18650 Liion battery.
@@opengreenenergy Can I use TP4506 instead TP5100 ?
What is the name of the glue you used at 7:03 ? Thank you
Hot glue gun
Hello , can you provide me enclosure on chargable basis
Is this abylable in pakistan
😍😍
It would be awesome if you can start selling this.. Would love to purchase
what will Total cost of any ups
What music?
اين ملف stl v3
Your ups sir constantly charging and discharging the battery, that's not good it should have by pass mode
No worries, the BMS protects the cells from overcharging. It will cut the charging if batteries are fully charged.
Bhai kitne main bhechega 😊😊
22:43 What load do you use when set the maximum current?
No load...outpot wire is just shorted.
Good project spoilt by dreadful music.
We need this one contact details
Can u sell this ups
You can Make For me ? I will pay you.
You should use 2s battery level indicator instead of voltmeter
You should sell!
Sorry to say but music is very chutia
sir, can you gift me
1 wifi ups😌?
Try some new projects.