Hi! is it good for Votol Controller EM-150 and Votol Controller EM-100?? I need ot for that and I have no USB cabnle, whít is the pinout to make one? Thanks! USB cannot work with only 2 wires it needs the common GND too!
Hello. I just bought the Votol em100 motor controller. Since it was not compatible with my motor, I programmed it with the program cable. However, when I removed the program cable, a static electricity jump occurred. The device does not work at all and does not connect with the PC program. Can you help me?
is "rate of decline" in Page1 to reduce or disable regen? what is combinative torque? my battery supports up to 10A regen/charger, how i set the controller to don't go over 7A or 8A when regen? can i enable the regen only when i'm braking and no when i left the throttle? thanks
I have Votol EM 100 model controler I. want to program it in 60V, 26 pole pair, 120 deg. Hall shift angle. So can your software in the link provided can help me out in programming my controller?
Dasz link do sterownika kabla i oprogramowania? Jeszcze pytanie bo strasznie agresywnie reaguje na gaz ma jakieś obejście tego wydaje mi się że przy 60procentach odkręcenia manetki już dostaje cała moc
Dzień dorby, chciałbym się dowiedzieć jak się sprawuje ten kontroler, na forach niektórzy pisali o zlych doświadczeniach związku z tym kontrolerem, albo od początku nie chodził albo po kilku dniach przestał działać. Jaka jest twoja opnia? dzięki
pewnie usterki fabryczne zależy jaki egzemplaż się trafi, z tego co wiem to votol em150 jest bezproblemowy w porównaniu do em200 ,a najbardziej niezawodnym sterownikiem jest sabvoton ML60 jeszcze nie widziałem uszkodzonego a sam jeżdzę na nim 2 lata to jest to samo co votol tylko słabszej mocy i tańszy. Jak zależy ci na tym em200 to kupujesz i zwracasz aż do skutku jeśli nie działa i dostajesz nowy.
Today while I was working with my controller I successfully connected my Controller with my PC using PL2303Module. Display window was showing Real time Voltages etc. I also downloaded bin files to Controller couple of times, everything was fine. But suddenly after communication between PC and Controller, and now whenever I try to connect with my Controller this message appears "Communication Abnormal, no response". Please help me if you have any idea about the issue. Please note that I have checked the wiring and have also replaced PL2303 module, but the issue is still there.
Hi, very informative, but I still get communication abnormal, no response Wired, charged 72v, windows changed to Chinese com port showing, Any advice please
Благодарю друг!
Hi! is it good for Votol Controller EM-150 and Votol Controller EM-100?? I need ot for that and I have no USB cabnle, whít is the pinout to make one? Thanks! USB cannot work with only 2 wires it needs the common GND too!
Hello. I just bought the Votol em100 motor controller. Since it was not compatible with my motor, I programmed it with the program cable. However, when I removed the program cable, a static electricity jump occurred. The device does not work at all and does not connect with the PC program. Can you help me?
is "rate of decline" in Page1 to reduce or disable regen? what is combinative torque? my battery supports up to 10A regen/charger, how i set the controller to don't go over 7A or 8A when regen? can i enable the regen only when i'm braking and no when i left the throttle? thanks
I have Votol EM 100 model controler I. want to program it in 60V, 26 pole pair, 120 deg. Hall shift angle. So can your software in the link provided can help me out in programming my controller?
that stock config? Where did you buy this set?
Do you have full system voltage going to the yellow electric door lock wire?
sorry i dont understand what you mean
I want to check if the speed limit is applyed or not in my bike, how this speed limit workign and why percentage is there not kmph?
Dasz link do sterownika kabla i oprogramowania? Jeszcze pytanie bo strasznie agresywnie reaguje na gaz ma jakieś obejście tego wydaje mi się że przy 60procentach odkręcenia manetki już dostaje cała moc
How to find to unknown controler program connecter and wires
Hi
I have 3 speeds backwards.
How can I change the direction of the motor, to have 3 speeds forward?
qs138-em200
Thanks.
basically switch 2 wires from any of the 3 phases wire ;) it is commmon for any 3phase brushless motor no need to config
Subscribe and Like :D
Dzień dorby, chciałbym się dowiedzieć jak się sprawuje ten kontroler, na forach niektórzy pisali o zlych doświadczeniach związku z tym kontrolerem, albo od początku nie chodził albo po kilku dniach przestał działać. Jaka jest twoja opnia? dzięki
Pierwszy sterownik - padł. drugi przysłali uszkodzony może to ja mam pecha ale No cóż ..
pewnie usterki fabryczne zależy jaki egzemplaż się trafi, z tego co wiem to votol em150 jest bezproblemowy w porównaniu do em200 ,a najbardziej niezawodnym sterownikiem jest sabvoton ML60 jeszcze nie widziałem uszkodzonego a sam jeżdzę na nim 2 lata to jest to samo co votol tylko słabszej mocy i tańszy. Jak zależy ci na tym em200 to kupujesz i zwracasz aż do skutku jeśli nie działa i dostajesz nowy.
Today while I was working with my controller I successfully connected my Controller with my PC using PL2303Module. Display window was showing Real time Voltages etc. I also downloaded bin files to Controller couple of times, everything was fine. But suddenly after communication between PC and Controller, and now whenever I try to connect with my Controller this message appears "Communication Abnormal, no response".
Please help me if you have any idea about the issue. Please note that I have checked the wiring and have also replaced PL2303 module, but the issue is still there.
I have the same problem, my controller is em200 2sp
@@fredycaldas3998 same problem with me also
@@gamingprotocol8871 same problem here.
Do you have any info on the usb cable? Is it something that can be purchased on amazon?
no my china friend give me for free
I have links on my channel for everything u need.
i have followed but the engine is not running. it makes a very loud sound .please help
please write mail :mpl01@wp.pl
ola voce tem o pdf ou esquema de como fabricar cabo
Hi, very informative, but I still get communication abnormal, no response
Wired, charged 72v, windows changed to Chinese com port showing,
Any advice please
I have the samw problem, i hace votol em200 2sp
@@fredycaldas3998 @richardwatts2190 @mpl02
same here, port showing, but still getting "communication abnormal"... did you figure this out?
@@fredycaldas3998hello friend, i have this problem too, did you solve this problem?
How many volts to do the connection
MAX 72V
We need English !!!!!
I have it!!!! Check out my votol em-100 vids. Enjoy! Feel free to sub while ur there!!
Sir thank you... the download link "1111"
fixed it. thanks