Hello, I would like to thank you for this video, I will be doing mine in the next couple days. Im assuming both locations need a router? Also my laptop doesn't have a ethernet port, do I need to contect the LAN port to my desktop? Thanks
Thanks for sharing this. It helped me to address the issue of "Transmit Power". I had mistakenly set CALCULATE EIRP LIMIT to ON. That gave me grief for days with Transmit Power.
Hi! Im having an issue, did this just like this, but ram on both devices goes up to 90% and sometimes 95 over 10 seconds, even going into a crash whit an error report
Please help Mr, can I use any of them as a wifi? I mean to share wifi to a specifc area, so I can provide an internet access for the people an this area? I mean to use Lite beam or nanostation as a wifi device and the wifi should reach to wide distance
thanks for the video!. I have four antennas in my link. So I need to connect Ant1 as access point like you did with your PointA antenna. What about my antennas 2, 3 and 4? The setup is the same as the setup you did for your PointB antenna? Thanks
@@wifilabxyz doesn´t work I need to do that: ant1 access point = on ptp = on ant2 access point = off ptp = on ant3 access point = on ptp = on ant4 access point = off ptp = on is not ptmp, is Ant1 pointing to Ant2-Ant3 poiting to Ant4
Not sure if you are still replying to comments, but if you are, a question. Do you need a router at both points? Or Just at PointA, and PointB can be connected direct to a laptop ethernet port?
hi Sir, can u make a video of shapping procedure, for example f i have 100mpbs net, i will divide it into how many clients, say for example 10mbps, 15mbps, 5mbps etc. thank u and morepower
Hello Friend - Happy Saturday !! - This video was amazing and super helpful. Do the PtP Ubiquiti dishes have to be within a certain proximity of the Starlink dish or the Mesh Router? We have tried to connect the ethernet adapter/mesh router to a Ubiquiti dish that is hardlined via CAT 6 cable about 300 feet away. So we are having connectivity issues to the Point A dish... in close proximity to the Starlink dish & Mesh Router it connects almost immediately -- however 300 feet away --- not working.
Ok I figured out the above -- the answer from the Ubiquit forum is that YES the dish needs to be in close proximity to the Mesh Router ---so it is captured in the "net bubble" of signal strength... NOW.. we have a NEW new issue... We have set up 2 sets of Ubiquiti dishes --- First set : Point A --> B .... Second Set: Point C --> D We tried using a splitter to connect both dishes to the Starlink Ethernet adapter which is connected to the MESH Router ... and that DOES NOT WORK - unfortunately .... Are you aware of any work-around to that issue???
I think I need to try to connect the two (2) sets of dishes using an ethernet switch -- I will try a 5 port gigabyte ethernet switch and see if that works
So I ordered a Ubiquiti 5Ghz Nanobeam Ac Gen2 and a Ubiquiti 5Ghz Litebeam Ac Gen2 to beam about 1km. I'm hoping the dissimilar hardware doesn't give me grief? I know I should have just bought 2 Nanobeams but was thinking I could save a bit and use the Litebeam as the PTP link (receiver)...
Hi there, I followed your instructions from start to finish, can ping and control the Remote Station but when I attach any computers or Video Surveillance I do not get any IP, can you shed some lights? Thank you in advance
Hi sir! I hope you are still around. Do you have a tutorial on how to change the IP address for both Point A and B? I have a new router that I wish to connect the Point A (source) and if I plug it there, there is no internet connection. Do I need to configure again both Points with the new router? Or is there an easier solution like changing it in the dashboard?
you can change the ip addresses of the antennas from their network settings. and do sure that the cables are connected properly to get connected to the internet.
Does the power need adjustment or is it always best to set it to max as you show? I have a 700m ptp link. How do you tell if the signal is good or bad and how can we improvei it? It woule be nice to have some info or even a video about these settings!
keep it full initially during the installation, it will help a little when doing an alignment. once you are good, reduce it if the signal is too strong. for a 700m link, -60 to -50dbm signal should be ok and keep the chain difference of not more than 3dbm.
@@wifilabxyz thank you for your quick reply. Could you please explain or link something about "chain difference"? Is it the difference between the power of the two stations? I thought they needed to be the same (for example 15 on pointA and 15 on pointB)
the chain difference can be found next to the local and remote signal of each antenna, it has a delta sign and color as well. green means ok, orange means a little alignment is needed and red means very bad signal, maybe more height is needed, the alignment is off or there is no clear LoS.
@@wifilabxyz sorry to bother again, I tried reducing the power up to 2dBm but I still get a red -50 delta6 dBm result. I did the alignment at full power and I have full LoS... Is there something else I should try?
Sir I adjusted the channel width to 40Mhz is that okey? Edited: Airtime speed riches to 300+Mbps when I change it from 20Mhz to 40Mhz and 600Mbps when I change it to 80Mhz.
Assalam.oalikum, Ddar brother Maine Litebeam AC Gen 2 Install ki hoi hai aur main basically village se belong karta houn ab main chahta houn 1 km ki range mein main 2,3 dostoun ko bhe connection doun to kiya yeh possible hai agr han to kyse?
hello wifilab, i have 2 questions, is possible to make a PTP between 5AC gen 2 and Litebeam M5? and, if its possible i can connect the 5ac Gen 2 to a wifi router without further configuration? Awesome video very nice tutorial thx
Bloody hell, it turns out that was exactly the problem. I just plugged it into a different socket and it started to work. I feel dumb. Anyways, thanks for the help!
so intriguing video , sir no need na po ba ang mga networks like smart at globe sa ganitong set up nakita ko na offline lang thru laptop at nkakamangha,pede po rin ba sa mga remote areas? respect my comment .thanks
Sir any recommendation for base and two stations. One station at 1.5km for 50Mbps and one statio. At 500m for 50Mbps din. Mgkakaharap lahat ng antenna sir.salamat po sa advice
Sir yung Point B my wifi din ba? pwede mg connect wifi device like mobilephone. or wala sya wifi .naka off kasi AP ng point B so hindi sya pwede sa wifi client?unless my wirelss router ako at kakabit ko sa point B
Sir, I have a question po. I'm currently using p2p connection and naka subscribe ako sa kilala ko na nagbubusiness nang WISP. But I'm planning na magpatayo nang sarili kong base tower na mag babato sakin nang signal. Kukuha ako nang internet sa house nang mother-in-law ko na naka pldt fibr pupunta sa bahay namin using p2p connection, bale gen2 gen2 din na setup. Do I need to reset po the settings of my old gen2 device pra ma set up to siya ulit? or how do I access the user interface nang old device ko pra ma configure ko siya?
Hello po bakit yung sakin di ko makita yung Access point PTMP airmax mixed? Yung AP is Litebeam 5 ac gen 2 tas yung Station M5 23, pag iniiscan ko nakikita nman sya pero di pwede i iclick yung AP.
@@Bryan-Hensley Make sure you have good line-of-sight between the two antennas. Trees and other obstructions will greatly reduce distance. Get as high as possible to ensure you have a clear path.
@@wifilabxyz 100mbs po yung internet..gawin ku sana 90mbs yung station .plan ku kasi mag negosyo nang wifi...sayang kasi yung fiber internet ko sa kabila
Simple, easy to understand. The diagram at the very start of the video was extremely helpful. Good job!
So far, you have been the only youtube vid to actually help me get this damn thing working with internet. :-) thanks.
Está procurando faz tempo um vídeo com o novo sistema da ubiquit você salvou meu dia obrigado
Thank you for this excellent video. I was able to watch it and set them up without any issue. Great Job. Salam
Bravissimo! senza neanche dire una parola mi hai fatto configurare il Bridge
Ibang klase to..
Salamat nito sir.. Kahit wala akong naintindihan heheh..
Pero nka ptp kasi ako.. Customer ako sa ptp.. Ito pla ginawa saakin net
...yoh this has been very insightful stuff of which, I had a walk over when I was setting up my 4.5km link
Thanks for sharing this setting. WELL DONE !!!
Thanks for doing this video. It is very helpful.
Thanks yar mana pali bar dish open ki thi or kamyab ho gaya ap ki waja sa tganks bro
Thanks for sharing this valuable information/knowledge. Keep it coming sir. Great job. Done: Liked and Subscribed.
Very well done, good Sir, thanks for the help!
Hello, I would like to thank you for this video, I will be doing mine in the next couple days. Im assuming both locations need a router? Also my laptop doesn't have a ethernet port, do I need to contect the LAN port to my desktop? Thanks
Talk about SIMPLIFIED. Nailed it!!!
Thanks for the video. It helped me a lot
Hi! Thanks for your vid! Can I add those LiteBeams to my Unifi Controller?
thank you, but could I ask you why did you used 20Mhz? It should have a lower throughput than higher channels like 40 or 80Mhz
Thanks for sharing this. It helped me to address the issue of "Transmit Power". I had mistakenly set CALCULATE EIRP LIMIT to ON. That gave me grief for days with Transmit Power.
Great tutorial, thanks much!
What's the speed acquired when located 3 miles away from each other on a good line of sight?
Thanks a lot. Very well done!
asome, tank you very much from mexico !!!
how is mexico now? i want some taco's
hello Thank you for the video. please how to limit the flow in station B? Thank you....
thanks for sharing
If the antennas are close together under 100m, do these settings will these settings work in this situation?
Hi! Im having an issue, did this just like this, but ram on both devices goes up to 90% and sometimes 95 over 10 seconds, even going into a crash whit an error report
Please help Mr, can I use any of them as a wifi?
I mean to share wifi to a specifc area, so I can provide an internet access for the people an this area?
I mean to use Lite beam or nanostation as a wifi device
and the wifi should reach to wide distance
thanks for the video!. I have four antennas in my link. So I need to connect Ant1 as access point like you did with your PointA antenna. What about my antennas 2, 3 and 4? The setup is the same as the setup you did for your PointB antenna? Thanks
ptmp will be different.
ant1
access point = on
ptp = off
ant 2 3 4
access point = off
ptp = off
these settings can be found with the latest firmware.
@@wifilabxyz doesn´t work
I need to do that:
ant1
access point = on
ptp = on
ant2
access point = off
ptp = on
ant3
access point = on
ptp = on
ant4
access point = off
ptp = on
is not ptmp, is Ant1 pointing to Ant2-Ant3 poiting to Ant4
Very good, thank you so much!!
Sy br bli lite beam 5ac gen 2 dan PBE m5 kira2 yg mn hrs jd Ap dan mn hrs jd stasion pak. Mksh jawab nya
why do you need to change pc ip to static.? it connects to setup wizard either way
Not sure if you are still replying to comments, but if you are, a question. Do you need a router at both points? Or Just at PointA, and PointB can be connected direct to a laptop ethernet port?
salamat sa video.it helps a lot👍
Thanks is a very simple tutorial but is amazing
hi Sir, can u make a video of shapping procedure, for example f i have 100mpbs net, i will divide it into how many clients, say for example 10mbps, 15mbps, 5mbps etc. thank u and morepower
Whats the long term reliability like
awesome! great! Thanks
Thank you very much
totally worked for me
superb! tinola is the key.
Can you tell me The max thoughput of a pair of this in real world?
Hello Friend - Happy Saturday !! - This video was amazing and super helpful.
Do the PtP Ubiquiti dishes have to be within a certain proximity of the Starlink dish or the Mesh Router?
We have tried to connect the ethernet adapter/mesh router to a Ubiquiti dish that is hardlined via CAT 6 cable about 300 feet away. So we are having connectivity issues to the Point A dish... in close proximity to the Starlink dish & Mesh Router it connects almost immediately -- however 300 feet away --- not working.
Ok I figured out the above -- the answer from the Ubiquit forum is that YES the dish needs to be in close proximity to the Mesh Router ---so it is captured in the "net bubble" of signal strength...
NOW.. we have a NEW new issue...
We have set up 2 sets of Ubiquiti dishes --- First set : Point A --> B .... Second Set: Point C --> D
We tried using a splitter to connect both dishes to the Starlink Ethernet adapter which is connected to the MESH Router ... and that DOES NOT WORK - unfortunately ....
Are you aware of any work-around to that issue???
I think I need to try to connect the two (2) sets of dishes using an ethernet switch -- I will try a 5 port gigabyte ethernet switch and see if that works
salamat sir.
pwde sa sunod sir galing router to sector to 5ac gen2 sabay ang limit nang speed. salamat.
Boss salamat s tutorial
Thanks pro❤❤
So I ordered a Ubiquiti 5Ghz Nanobeam Ac Gen2 and a Ubiquiti 5Ghz Litebeam Ac Gen2 to beam about 1km. I'm hoping the dissimilar hardware doesn't give me grief? I know I should have just bought 2 Nanobeams but was thinking I could save a bit and use the Litebeam as the PTP link (receiver)...
it should work with no problems...
Bilis Yan anper land line homer fiper
This is really Good
however, My distance is about 2km apart, does the power output remain the same as stated in the video
if it is a long distance, the higher the power the better the signal will be.
Just to ask, is PoE Injector included in the package when you purchase?
Mine did.
yes sir.
Can I connect lite beam with power beam station because I have already connected one power beam I want to connect lite beam now.
yes u can.
hi Sir @WifiLab if I purchase this and follow these steps will I have my own internet? Do I need a monthly subscription?
u still need an internet.
Salamat
Ini litebeam ac jarak tempur berapa kilometer biar stabil & josss
Hi there, I followed your instructions from start to finish, can ping and control the Remote Station but when I attach any computers or Video Surveillance I do not get any IP, can you shed some lights? Thank you in advance
please make sure that a.) DHCP server is enabled b.) point A antenna LAN cable is connected.
Thank sir, 🥰
May tinola sa Qatar
. Thanks sa tut
Hi sir! I hope you are still around. Do you have a tutorial on how to change the IP address for both Point A and B? I have a new router that I wish to connect the Point A (source) and if I plug it there, there is no internet connection. Do I need to configure again both Points with the new router? Or is there an easier solution like changing it in the dashboard?
you can change the ip addresses of the antennas from their network settings. and do sure that the cables are connected properly to get connected to the internet.
@@wifilabxyz do you have a video how to do it?
Does the power need adjustment or is it always best to set it to max as you show? I have a 700m ptp link. How do you tell if the signal is good or bad and how can we improvei it? It woule be nice to have some info or even a video about these settings!
keep it full initially during the installation, it will help a little when doing an alignment. once you are good, reduce it if the signal is too strong. for a 700m link, -60 to -50dbm signal should be ok and keep the chain difference of not more than 3dbm.
@@wifilabxyz thank you for your quick reply. Could you please explain or link something about "chain difference"? Is it the difference between the power of the two stations? I thought they needed to be the same (for example 15 on pointA and 15 on pointB)
the chain difference can be found next to the local and remote signal of each antenna, it has a delta sign and color as well. green means ok, orange means a little alignment is needed and red means very bad signal, maybe more height is needed, the alignment is off or there is no clear LoS.
@@wifilabxyz tank you!
@@wifilabxyz sorry to bother again, I tried reducing the power up to 2dBm but I still get a red -50 delta6 dBm result. I did the alignment at full power and I have full LoS... Is there something else I should try?
Is this better than using the app (for 2 antennas, simple home setup with a mesh internet)
if you want to go further, use a laptop otherwise the app is enough for basic configuration.
@@wifilabxyz I have tried. They will not work. I wonder if it is because I have a mesh router.
hmmm it could be but this is just a simple ptp. mesh has nothing to do with it.
thanks
Спасибо большое. Очень помогли.
can any connect from PointA? i noticed that you just scanned and clicked the source from PointA. you didnt input a password.
i did put a password to connect to point A...
Sir I adjusted the channel width to 40Mhz is that okey?
Edited: Airtime speed riches to 300+Mbps when I change it from 20Mhz to 40Mhz and 600Mbps when I change it to 80Mhz.
it is ok. you just had doubled the bandwidth.
@@wifilabxyz thank you
Pwede po ba maging repeater yung antenna nato?
Assalam.oalikum, Ddar brother Maine Litebeam AC Gen 2 Install ki hoi hai aur main basically village se belong karta houn ab main chahta houn 1 km ki range mein main 2,3 dostoun ko bhe connection doun to kiya yeh possible hai agr han to kyse?
so i need a little help. im 4km far from the place that i wanna get internet from so what's better tp-link cpe 710 or Ubiquiti LiteBeam
litebeam is better for me.
@@wifilabxyz have u tried 4km on litebeam?
yes, it works perfect.
@@wifilabxyz thnx brother!
pointA is a Sender? or base? station?
base, source of internet.
Confused in the beginning you set the IP addresss of the computer to 192.168.1.111 and then the antenna to 192.168.1.151 why the difference?
because in an IP network, no IP adress should be the same.
Talk, please! Why did you disable Calculate EIRP limit?
by disabling it, you are forcing the antenna to a maximum power.
Where can I configs for antenna use
Ito pala ung point to point.
hello wifilab, i have 2 questions, is possible to make a PTP between 5AC gen 2 and Litebeam M5? and, if its possible i can connect the 5ac Gen 2 to a wifi router without further configuration? Awesome video very nice tutorial thx
1. if ap=on ptp=on, m5 cannot connect however if ap=on ptp=off, m5 can connect.
2. no further configuration needed, ptp is just a bridge connection.
@@wifilabxyz the ap must be the AC or the m5? Thx for the fast reply. New follower.
must be the AC
For some reason I don't get internet after removing the static IP. The setup was otherwise successful. Do you know what I might be missing?
is point A connected to a router with DHCP enabled?
Thanks for the reply. Yep, DHCP is enabled. Any idea what else it could be?
well, if the wireless link is a success. maybe u need to double check the physical connectivity of your antenna to your switch or router.
Bloody hell, it turns out that was exactly the problem. I just plugged it into a different socket and it started to work. I feel dumb. Anyways, thanks for the help!
glad it worked!
hi sir, sa point b ba, no need lagyan ng center frequency? napansin ko sa video mo na nag lagay ka ng 5800 sa point A, pero sa B,sensya na newbie here
no need na sir, sa point A lang need.
so intriguing video , sir no need na po ba ang mga networks like smart at globe sa ganitong set up nakita ko na offline lang thru laptop at nkakamangha,pede po rin ba sa mga remote areas? respect my comment .thanks
with or without internet pwede lang. ex. ip camera. pwde kahit saan basta me line of sight between the 2 sites.
Where's the audio?
this can work for Bahamas?
yes...
Sir any recommendation for base and two stations. One station at 1.5km for 50Mbps and one statio. At 500m for 50Mbps din. Mgkakaharap lahat ng antenna sir.salamat po sa advice
go for ptp setup for each para iwas latency issue. taas kc ng 50meg.
qatar to the rescue! thanks!
gen1 lang gamit ko kapiso. malapitan lang kasi
boss kung maglagay kanang router sa client same ba ip sa antenna mo or pwede kahit anung ip ilagay? thanks sa sagot..
depende kung ano setup ng network mo sir pero malimit pag flat network ka, the same ip sir.
Hi! so dun din ako sa wifi ko coconnect right? after setting this up?
u need a wireless router to be connected at the LAN of the PoE injector of Point B antenna.
Ptp litebeam 5ac gen2, 2 buah... Buat 3km bisa bawa bandwith 300mbps mas?
3km 300mbps? litebeam no. use af5.
para san po yan? meron kasi kapitbahay namin ganyan..pag bumili ako ng ganyang antenna magkaka intenet na ko?
Sir bakit wala po sa selection yung Access point PTMP airmax mixed?
anjan po dapat.
Sir yung Point B my wifi din ba? pwede mg connect wifi device like mobilephone. or wala sya wifi .naka off kasi AP ng point B so hindi sya pwede sa wifi client?unless my wirelss router ako at kakabit ko sa point B
pwde lang sir, instead of laptop kabitan mo ng access point or router para magkawifi.
@@wifilabxyz let say meron akong TP LINk wireless router . dun ko kakabit si Point B? then si tplink wlan router na mag serve as Lan and wifi?
yes sir...
@@wifilabxyz ty
Sir, I have a question po. I'm currently using p2p connection and naka subscribe ako sa kilala ko na nagbubusiness nang WISP.
But I'm planning na magpatayo nang sarili kong base tower na mag babato sakin nang signal. Kukuha ako nang internet sa house nang mother-in-law ko na naka pldt fibr pupunta sa bahay namin using p2p connection, bale gen2 gen2 din na setup.
Do I need to reset po the settings of my old gen2 device pra ma set up to siya ulit? or how do I access the user interface nang old device ko pra ma configure ko siya?
kung wala kang access sa old device mo, better reset it tapos follow mo na lang tong video kung pano mag ptp.
@@wifilabxyz thanks idol! More power!
hello sir
yung point B EIRP di naba babagohun?
kc sa piont A binago mo
thank you
point a at b naka off po sir.
@@wifilabxyz salamat idol new subs po ako sayu
salamat sir.
Hello po bakit yung sakin di ko makita yung Access point PTMP airmax mixed?
Yung AP is Litebeam 5 ac gen 2 tas yung Station M5 23, pag iniiscan ko nakikita nman sya pero di pwede i iclick yung AP.
try nyo pong e upgrade sa latest fw ung dalawa nyong antenna.
sir , 2nd question tama lang po ba na 5800 ang center frequency nya . or san dapat kunin ang center frequency ?
depende kung anong malinis na frequency sa lugar nyo. run mo ung airview at dun mo makikita mga malilinis na frequency.
sir , tanung ko lang . wala kasi sa video , anu lalagay sa device mode ? - access point ptp / station ptp ? for p2p
point a
ap - on
ptp - on
point b
ap - off
ptp - on
Hellow sir sana mapansin applicable po ba to sa 300meters range? Salamat.
pwede lang sir. adjust mo na lang pababa ung power.
I'm not able to get very much range. About 300 to 500 meters is the maximum range I can get
it should go for more than that...
@@wifilabxyz when I get time I'm going to do some more experiments
@@Bryan-Hensley Make sure you have good line-of-sight between the two antennas. Trees and other obstructions will greatly reduce distance. Get as high as possible to ensure you have a clear path.
@@Texas1FlyBoy I managed to get a 1.2 mile connection around 60 dbi signal. I'm catching on. Thanks
Destination net unreachable pano po I fix?
check the cable.
Need pa po ba magbayad monthly for the internet connection?
yes sir need pa din.
pag ping ko sir transmit failed. bat ganun? nung na set ko na sa 192.168.1.151
reset mo at follow mo ulit ginawa ko
ok na sir?
sir.. gen2 pero bkit 300meter lng?? kya paba gawing 5km yan??
by default sir kapag nagtest ka ng antenna na magkatabi lalabas na 300m lang. kaya naman po ang 5km...
pag lbe 5ac gen2 ilang max range po? pwde po ba yung ap ko is lbe 5ac gen2 at yung station is lite beam lng po? kaya po ba 6km ? salamat po
pwde po ang mixed mode sa litebeam. kaya din po ang 6km basta me clear LoS lang.
@@wifilabxyz maraming salamat..akala ku hndi kaya na lbe 5ac bumato nang internet 6km..malaking tulong po ito salamat po
ilan mbps need nung kabilang station?
@@wifilabxyz 100mbs po yung internet..gawin ku sana 90mbs yung station .plan ku kasi mag negosyo nang wifi...sayang kasi yung fiber internet ko sa kabila
malabo sir pag litebeam tapos 90mbps ibabato nyo. di kaya ni litebeam
Hello po sir, mine po nung una nagbabato na ng 90mbs punta sa point A to point B, pero ngayon bigla bumaba ng 10mbps nlng, ano po kaya nangyari?
mukhang me port problem ka sir. pacheck na lang po ung both LAN ng antenna mo. baka naka 10mbps lang...
Thank you for this. Ubi "documentation" writers are very much overpaid. I'd just fire them for wasting so much of my time. Possibly everyone's?
pwedy kaya litebeam sa Globe modem?
globe modem as a source of internet? pwde lang sir.
hanngang ilang kilo metro kaya niyan?
around 10 to 15 km.