Correct Answer - I took another brushless motor which was geared and used it as a generator. I chose any 2 of its wires and connected it directly to my CPU Fan wires. After that, when i turned it really slow, the frequency of the generated AC also became very less giving my CPU Fan time to catch-up to the changing poles and start the running part slowly. After a few mili seconds, the poles got locked to the changing magnetic field there by making it synchronised and hence the rotation. Faster i cranked my generator, faster the cpu fan moved.
He used a ac fan voltage regulator. If you do a phase shift as he has two sets of poles already then without that magic he can start it directly with a standard 12v ac supply. Why do we have a caps in ceiling fans and domestic motors?
Hi I feel 2 things either you used capacitor, or you used the power supply DC and changed polarity for it to turn clockwise and anti-clockwise, I also feel this because the RPM increased without voltage change you cannot increase RPM AC transformer was 12V stable!! 😂😂😂😂 Great Video 👍🏻👍🏻
@@MrElectron No worries Brother I do watch your videos will get it soon not an issue, just a query, I saw you winding the armature, two of the poles were wound clockwise, did you wind 2 anticlockwise or I understood wrong😂😂😂😂 please throw light, thanks a ton for reply Brother
I took a small bldc motor and wired it up to 8volt AC and it didn't spin but it buzzed and vibrated back and forth so what I did is took a capacitor and wired it to the other wire and the center wire and then it turned on
I have a burnt hall sensor in one fan, I have a second one, I want to connect it connected via 3 wires to the coil of a working fan, type 1 hall sensor for 2 fans, will it rotate?
even though it's BLDC motor, at the end it's runs on ac signal, where driver circuit do the conversion, yet I'm curious which method u used to run that motor, I'm subscribed to see the following video.😇
Hii bro in this project you have used dc supply and we all know that dc does not change it's polarity like ac that's why you have not pushed the fan rotor... I hope i am correct... 👍👍👍👍
Dear Mr Electron I watched your video on how to reverse a universal motor using a dpdt switch. Please advise how to attach speed control to that. I have a dc speed controller 2 wires for the motor and two for the battery. Can you please advise where to put the two wires to the universal motor. I’ve tried a few things and it’s not working. Your help would really be appreciated. Thanks
In line with the hot wire of the motor so it will work like a dimmer switch instead of just adding an overexertion of ohms and or resistance to your circuit because it's easy to do that when your asking this motor to not only change it's original duty cycle and direction! But it's speed too?! Hold on I'm gunna yell some loud things so I feel better..
@@northwestrockgem9745 I connected one of the motor speed control wires to the middle of the dpdt switch and it worked, the other wire was not needed, that’s weird !!
Sir make a copper wire spot welding machine on computer ups transfer. . Dose we melt 18 gauge wire for motor ..i need this type bt market have this machine price is 3000+.. I have a old ups bt safty components ke saath app ek video banao please. .
I noticed everyone on you that showing how to wire motor alway skip ⏭ that part how to wire is set so it can work and why is all lie why 62 videos do the same thing all I want to do is learn and can find a video showing if the wire all wind right of left
BEST BATTERY CHARGER DIY VIDEO - ua-cam.com/video/ZN3saILbYUw/v-deo.htmlsi=9_nLu0vKOqfn4zi_
*Join this channel to get access to perks:*
ua-cam.com/channels/WFbPzBb7dCyCWuBA-DBrMA.htmljoin
*Mr.Electron Patreon's Page* - www.patreon.com/mrelectron
*Hindi Channel* - www.youtube.com/@Mr.ElectronHindi
*Alternator Channel* - www.youtube.com/@mrelectron_alternator
*Watsapp Channel* - whatsapp.com/channel/0029VaQmmRaFCCoWOf7huh3G
Correct Answer - I took another brushless motor which was geared and used it as a generator. I chose any 2 of its wires and connected it directly to my CPU Fan wires.
After that, when i turned it really slow, the frequency of the generated AC also became very less giving my CPU Fan time to catch-up to the changing poles and start the running part slowly.
After a few mili seconds, the poles got locked to the changing magnetic field there by making it synchronised and hence the rotation.
Faster i cranked my generator, faster the cpu fan moved.
I am really exciting to know the answer bro....give it soon
You gave it dc current than it ran
Try to make a super high speed brushed motor
No dc
Change it's polarity
Mr electron ur videos are good n helps me for not ruining lot of thing out of curiosity
You may have used phase angle control, or a back emf controller to detect when to turn on the coil.
He used a ac fan voltage regulator. If you do a phase shift as he has two sets of poles already then without that magic he can start it directly with a standard 12v ac supply. Why do we have a caps in ceiling fans and domestic motors?
Hi I feel 2 things either you used capacitor, or you used the power supply DC and changed polarity for it to turn clockwise and anti-clockwise, I also feel this because the RPM increased without voltage change you cannot increase RPM AC transformer was 12V stable!! 😂😂😂😂 Great Video 👍🏻👍🏻
Thanks !! No i didn't use any dc supply or a capacitor
@@MrElectron No worries Brother I do watch your videos will get it soon not an issue, just a query, I saw you winding the armature, two of the poles were wound clockwise, did you wind 2 anticlockwise or I understood wrong😂😂😂😂 please throw light, thanks a ton for reply Brother
I think you used some kind resistance or frequency controller
at 10:00, in other words, there is LOCK-UP during all-Attraction and during all-Repulsion.
I think you use dc current with the help of diodes bridge rectifier or use switching transistor or switching ic like 1 0 1 0 1 0 👍
First you decrease the frequency to start rotate then you increase the frequency gradually....is this right?
Correct but how
You may using the inverter while inversion you can control the frequency of output voltage and current.
When normal DC 12volts how to run if the IC is burnout or is their any way to run it without using IC?
What will happen when we connect one capacitor to this, by giving 12v AC?
I took a small bldc motor and wired it up to 8volt AC and it didn't spin but it buzzed and vibrated back and forth so what I did is took a capacitor and wired it to the other wire and the center wire and then it turned on
You use a lamp dimmer to lower the frequency of the ac mains
Agir ese 2 fan air cooled bike k engine k baju me lagaya tho kuch fayada ho sakta hai kya?
Where do u get those all motors
It's make me very happy to see such methods of education. Thank you and may so many find themselves passing along in this way of education.
The thumbnail 🙈💥
paired windings to AC on a straight line. the second pair of windings through the capacitor
Muito bom 👍 sucesso aí família 🤝👍👈
I have a burnt hall sensor in one fan, I have a second one, I want to connect it connected via 3 wires to the coil of a working fan, type 1 hall sensor for 2 fans, will it rotate?
Why are u showing motor working anti clockwise ? when i was taught it is always clockwise ? please can u explain, thanks
Its never fixed. Your washing machine works in both clockwise and anti clockwise
I think u have used bldc 3phase(modified only 2phase) driver circuit as its come with speed control.
No ...
Ur are very good and helpful to me. Good explanation also I am a fan of u 😊
Thanks
I think maybe you use the capaciter like normal ceiling fans.....
No capacitor
@@MrElectron then speed controller
Use 4 diodes as rectifier?
PHEW!!! GRABBED MY PPE JUST IN TIME WHEN YOU STARTED GRINDING 🤓🥸🧐
Can I make washing machine induction motor to 220v generator using neodymium magnet,is it possible?pls reply
Nice video Good narration and Good explanation 👍🏻👍🏻 expecting more videos
Mr electron where r u from
even though it's BLDC motor, at the end it's runs on ac signal, where driver circuit do the conversion, yet I'm curious which method u used to run that motor, I'm subscribed to see the following video.😇
LED on one line in the correct polarity.
mỗi lần chạy phải quay tay?
Hii bro in this project you have used dc supply and we all know that dc does not change it's polarity like ac that's why you have not pushed the fan rotor...
I hope i am correct... 👍👍👍👍
No dc only ac can be used in such a situation
Thanks for correcting my answer bro... 🥰🥰
how much Price of one jumper cable?
thats why permanant magnets are rarely used in ac motors.
Permanent magnets are actually used in synchronous motors
Nice work
Why would you undo this i don’t know but this is cool
wow don't know I could do that experiment with a bigger engine thank you for the video.
Dear Mr Electron
I watched your video on how to reverse a universal motor using a dpdt switch.
Please advise how to attach speed control to that.
I have a dc speed controller 2 wires for the motor and two for the battery.
Can you please advise where to put the two wires to the universal motor.
I’ve tried a few things and it’s not working.
Your help would really be appreciated.
Thanks
In line with the hot wire of the motor so it will work like a dimmer switch instead of just adding an overexertion of ohms and or resistance to your circuit because it's easy to do that when your asking this motor to not only change it's original duty cycle and direction! But it's speed too?! Hold on I'm gunna yell some loud things so I feel better..
@@northwestrockgem9745
I connected one of the motor speed control wires to the middle of the dpdt switch and it worked, the other wire was not needed, that’s weird !!
So I have two of the dc motor controller wires going to positive and negative.
And only one wire from the controller going to the dpdt switch !!
I have a 3 type of motor from old VCR....
How to make a DC generator
You just made a synchronous motor
Correct ! But how did it self start
alternating current with low hertz(frequency)
switching on off on off at particular time like that..., so it gains speed, it's hard to tell in text maybe u can understand what I said
Got it but still i didn't do that.
Nice presentation
Hand generator , lower frequency , slower switching
You used capacitor instead of rotating manually...is this right?
No
Creio que usar o sistema Bedini fica mais funcional.
alternating current with low hertz
Sir make a copper wire spot welding machine on computer ups transfer. .
Dose we melt 18 gauge wire for motor ..i need this type bt market have this machine price is 3000+..
I have a old ups bt safty components ke saath app ek video banao please. .
Damper winding ?
No damper winding
Run through DC supply
You used 2 phase esc
Frequency control I think so
Great video, thanks 😁👍
Making things very interesting.... 👍
R u a engineer
Yes
Hi bro
U just connect and disconnect wire very fast
You give ac input
Correct but how did i achieve the self starting part
@@MrElectron I think you connect capasitor
You used ac volteg
👍👍👍
Amazing videos
I have some repair videos
LED.
hello
Bravo test first fail why 4 pin and now ok 2
u used DC power source...
Good job
Why?
?
👍
DC
Nice
First Viwe..First Like
I noticed everyone on you that showing how to wire motor alway skip ⏭ that part how to wire is set so it can work and why is all lie why 62 videos do the same thing all I want to do is learn and can find a video showing if the wire all wind right of left
Nice
hello