How to REBUILD a DISTRIBUTOR
Вставка
- Опубліковано 16 чер 2018
- Distributor rebuild kit: www.kbox.ca/catalog/product_in...
Don't want to rebuild it? Here's a brand new one: amzn.to/2prglUY
Please double check fitment with your 4AGE powered car first :)
Got rid of the distributor in your 4age engine? Seal up the hole with the D4A distributor delete: www.driving4answers.com/produ...
To rebuild a distributor we are going to need a distributor, obviously, a distributor rebuild kit and some tools.
The first thing we are going to do is to remove the little gear at the end of the distributor shaft. It's held in by a pin which is flared at its ends.
The easiest way to remove the pin is to place the distributor in a vice, punch a little pilot hole and then basically drill away the flared part of the pin.
After this you can punch out the pin. The pin has been in there for a long time so it might need some persuasion to be punched out. Heating it up a bit and spraying penetrant helped in my case
Before you remove the gear make sure to make some marks so you know which you to re-install it. The gear is easily removed with a gear puller.
Once the gear is removed, remove the distributor cap, heat shield, if you have one, and the rotor. You will then have access to the two tabs which hold down the distributor shaft. The tabs are held in place with Philips head screws. Unscrew the bolts and retrieve the tabs by using some needle nose pliers. Once the tabs have been removed you can get the shaft out.
Once the shaft is out you can replace the old inner seal with a new one from your rebuild kit.
Remove the old seal using needle nose pliers and clean up the area where the seal sits. Oil up the new seal and install it using a socket that is just slightly smaller than the seal.
After this you can replace the bearing on the distributor shaft. The first thing you need to do is measure the exact distance between the bearing and the trigger. Write down the measurement. This will ensure the new bearing is reinstalled in the exact same position as the old one. Before removing the bearing I like to sand the shaft with some very fine grit sandpaper.
To remove the bearing, place the shaft in a vice and remove the bearing using a gear puller. You can also use the opportunity to remove the rust from the trigger and the rest of the shaft.
You can reinstall the new bearing by using the gear puller once again. Its also a good idea to use a washer to protect the new bearing when installing it. Once installed don't forget to confirm that the new bearing is in the same position as the old one.
After this you can reinstall the shaft into the distributor hole. Lube up your shaft and simply slide it into the hole.
Next up reinstall the gear by using a new pin from the kit. The pin in the kit in the link above does not need to be flared and simply needs to be hammered in. The hammering action mushrooms the top and makes it secure.
After this all that's left to do is to replace the other two o-rings on the distributor and reinstall the rotor, cap and heat shield.
Thanks for watching
Intro song: Kiss by Escape
#d4a #distributor #rebuild #diy #howto #4age #4age16v #aw11 #ae86 #4agebigport #mr2mk1 #mr2 #toyota #jdm #celica #corolla #starlet #ke70 #fx16 #fix #repair
D4A (driving 4 answers) is part of the amazon associates program - Авто та транспорт
Distributor rebuild kit: www.kbox.ca/catalog/product_info.php?products_id=34
Don't want to rebuild it? Here's a brand new one: amzn.to/2prglUY
Please double check fitment with your 4AGE powered car first :)
Hey is there anywhere else selling a new one
I've watched all your MR2 videos, great stuff! I also love that you post your scripts on most of your instructional videos!
You actually checked out the video description. That makes you a one in a million :)
"Lube up your shaft and simply slide it into the hole."
I knew something was coming. XD
Very well made video as always.
Big XD
He had to say that right when my mom walked into the room 😂
Love the intro :)
Great vid! Future me when he rebuilds the distributor AGAIN will thank you 👍
wow man, the intro of your videos is just awesome!
new video needed bro... how to check for a clogged exhaust ... thanx for the effort man... lots of love from Egypt
Love the videos, just be careful when using heat to 'persuade' steel as it can drastically change the metals structural properties. Most gears are specially heat treated to harden them without making them too brittle. Heating can make the steel soft again which will wear out the gears quickly causing premature failure.
Very informative!!! thank you so much for this amazing tutorial!
Thanks for the video, my rebuild kit has been sitting in a box for some time now
Very good work brother I appreciate your time and effort Thankyou
Harbor Freight sells a heavy duty chain breaker for less than $20 out the door. Use a coupon and save even more. I tried a vice first and it wasn't happening. With the chain breaker, a long 17mm socket, and. 3/8" ratchet about 8-9" long, the pin snapped out of it's locked position in less than 10 seconds. Just push the chain breaker's handle against a flat surface and hold the back side down with your off hand. The seemingly impossible turned trivial when the right tool was deployed. Do make sure the punch pin is correctly lined up with the shaft pin before cranking down with the ratchet.
Awesome technique....thanks for sharing your video.
Thanks a lotzzzz!,watching you from Bangladesh
Very useful info. Thanks for sharing!
Gotta love D4A!
Does anyone have an opinion on whether it makes sense to use a little AT-205 Re-Seal on my new distributor seals before reinstalling them? I'd like to minimize the risk of a leak and maximize the lifespan of these seals.
Thank you! Even though you didn't need it .
great tutorial :D
hey man, really helpful thankyou. im just a little timid about replacing wires, do you have any recomendations for tutorials on doing this?
Thanks for sharing.
Thanks man 👍🏻
i opened the ep91 4efte distributor to stop the oil leak and discovered the teflon seal inside. It needs to be replaced but there is no information about it and no OEM on the parts website. Why?
I changed both gaskets but obviously the oil gets through the dented arm all the way in the rotor box. Please help.
nice vid btw smallports have no knock pin the gear is just pressed on
the distributer cap in this video is exactly the same of my 4age ….. the problem is the cap is broken ….. and cannot find the exact same cap …. will the blacktop’s distributer cap serve the purpose?
Hi thete i have a 1997 celica with 1.8l my distributor started leaking inside i think its the seal do you know who might sale it and is it repairable
Hello. I have 4afe engine and i have check engine light. Guy who scaned my car told me that its distriburator, and other guy told me that i need to change it but he didnt took cover off to see for if something is broken etc. also he told me to look for this thing in junk yard for new one because i cannot buy new distriburator with that gear etc. Can you help me pleaase? thanks.
Very helpful
That power stance at 2:44. Distributor in for a beating.
Hahahahah!
Hey whats the distance those magnets need to be away from the tips on that shaft? I took my 4age mr2 distributor apart to clean out oil. I set them so they are barely touching. To where its not hard to turn each time. Did i do that right? Or do i need a file guage?
There are specs in the factory service manual, you can't really eyeball it, unless you're really lucky. But if the distributor worked well before there's no need to reset them.
Awesome video. Thanks for making it! Do you have to make sure your engine is in a particular position before removing the distributor?
You can remove it regardless of engine position. But you have to put the engine back to tdc and align the distributor gear with the mark on the body when reinstalling it.
It's always a good idea to put the car into tdc when pulling the dizzy. The dizzy will typically have some kind of markings, (in our case, 2 dimples) that will line up at tdc. And you can just use whiteout or a sharpie to mark the adjuster bolts
driving 4 answers thank you!
Erwin Bautista thank you.
Good thing you've made this video, i figured the distributor on my 4AGE is leaking ! BTW which engine do you have ? Mine is a Bigport Red and Black top, does your kit fits this engine too ?
It's not my kit. I believe it fits.
Thankyou
You didn't address the electrical components, which actually are the main issue with my Carina 3sfe distributor!
My distributor has no rolling pin. The pin is moulded as one full piece. No way to remove. What do I do? HELP!
I put a gear puller on mine put it in a vice grip to prevent the gear puller to open up hit it with a torch and penetrating oil and used a socket wrench to apply as much pressure on the gear
Thank you
The Frankenstein Celicas I build, thank you too.
I love you man. Great vibe! I have a Starlet 4efte distributor that I want to disassemble and change the bearing. Procedure must be similar?
Yes, likely very similar but always proceed with caution and don't force anything
@@d4a Thank you for your response. Today we pulled out the distributor and we opened it to replace the bearing. Unfortunately I did not find any replacement kit on the Internet (besides the 2 gaskets, rotor and cap) and it is impossible to find the internal Teflon oil gasket. I figured it out opening it. The Toyota manual doesn’t show what is inside the mechanism. Your video was helpful but the Starlet distributor is different. The magnets moved so thanks to the manual I’ve managed to distance the magnets and get get back in to nominal measures. I’m glad it worked out. .
D4A i miss this intro!!!!!!!!!!!!
Where are the windings of the distributor
also. the seal had worn a grove into my shaft and it still leaked after changing to a new seal, inspect your shaft folks! :D lol
5:10 🤣 Dang!
nice now i can rebuild mine as it leaks, instead of sending it to an engineer. would be handy to have a quick reinstall overview. for timings sake :)
Here's a quick reinstall overview: Rotate engine to TDC. Align mark on distributor gear with mark on distributor body. Install. Be careful that the gear doesn't shift when reinstalling. It really helps to have the cam cover removed when reinstalling. After this get a timing light and rotate distributor until you are at 10 btdc.
you are a scholar and a gent
Caint find any rebuild kit for my 4ag distributor ! You must have bought the last one ....
It's here....www.ebay.co.uk/itm/253942557917?ViewItem=&item=253942557917&PPX000600&ppid=PPX000600&cnac=GB&rsta=en_GB&cust=8VN01039G5553371L&unptid=5b649396-710a-11e9-b434-441ea14ee788&calc=6f3c0100d1990&unp_tpcid=email-auction-payment-notification&page=main:email:PPX000600:::&pgrp=main:email&e=cl&mchn=em&s=ci&mail=sys
How do you time the distributor after rebuilding the engine head ??
Timing light?
@@d4a I don’t have one
Buy it? Your alternatives are voodo and fortune telling.
#protip: i used a slightly modified motorcycle chain tool to press the pin out :)
Is that an aw11 cap? It looks strange
I think this is an ae92 cap. My car had parts from at least three different 4ages in it. But the distributor worked fine.
Lost it at "lube up the shaft, and slide it in"
Where am I
Not because I need to,
Cause I want to.. gentleman
Good video but no way this is an easy DIY!!
first
Indeed you are. Here's a virtual high five.