Hello from Lucknow Anna, your have explained it very well. Could you also demonstrate the ways to power headlight via batteries only so that there would be no need to use that switch at the rear shocx and the point settings for advanced firing for that liveliness in the pickup of Yezdi and that stunning reverse kick which scares the kids away :D
Hari Prasad ji do you not need to set the point gap at BTDC after setting the gap of 0.4mm at TDC by bringing the piston down by 2 to 3mm then again set the gap at maximum0.05mm by rotating the complete stator to either left or right to increase or decrease the points gap respectively? This is the recommended procedure to set the ignition of Yezdi in the user manual.
Hello I am from Allahabad, UP. While adjusting the points is it not necessary to set the point gap at BTDC ( behind top dead centre) also? which is as per the manual should not be more than .05 mm.
Yes, it is. I tried to do that but couldn't. Manual says, stator should be rotated clockwise/anti-clockwise. However, when I try rotating the stator, entire point rotates along with it making no difference to the gap. It is just ridiculous.
@chrispbacon5027 I am also from Allahabad and have been riding Yezdi for the last many years I have never had any problem with setting the point or to be precise, the ignition timing. The correct process is to set the point gap at TDC, which should not be more than 0.45 mm. I use a ballpoint pen body to mark both TDC and BTDC. I drew a 15mm line with 5mm markings on the ball pen body.. When the DTC has been reached( by rotating the crank clockwise), set the point gap to 0.45 or less. The BTDC is selected by rotating the crank anti-clockwise to bring down the piston by 2.5 to 4 mm. which be easily achieved by allowing the piston to go down between 2.5 and 4mm by watching the marking on the ball pen.The point gap at BTDC should not be more than .05mm. If it is found less loosen the magnet screws slightly and turn the magnet to the left till the correct gap is set, on the other hand if the gap is more then turn the magnet( the complete stator) to the right. Then tighten the two screws. With little practice it becomes very easy. Just try it.
@@RammoyRay I do the exact same thing, except I keep the breaker gap at 0.35mm at TDC. At fiting time (2.5 mm on the left to TDC), I keep the breaker gap 0.04 mm. Even after doing all these, my Yezdi is giving me a hard time. It only starts backward (reverse). I suspect that coiling is damaged. I am tired of this shit and I am going to convert it to CDI.
Sir please make a video on how to get tyres of yezdi as 3.25-16 is not available easily and the wholesaler don't have this tyre size so please make a video on how we can fix tubeless tyres which can fix into yezdi
Dear Sir ,I had a JAWA model 1974 ,which by default I sold it on 2009, now after couple of years I was quite disturb for it's absence.Pl advice me if I get Jawa bike not yezdi, is it possible to get 2nd hand JAWA now a days and then can it be renovat with new original spares through you as you have displayed in the video with the fantastic new original colour(Red) .please reply at the earliest.
Sir, of you get for me it will be better, I am trying from my side also ,I just want to confirm that if I get then will you help to renovate it from your side.pl reply Sir
At present I don't have any bikes with me. Mainly I am not interested in bike deals. If I get any information about Jawa I will give you contact details of owner
, I am not asking for deal, what I mean to say If get JAWA from my own, can you renovate with full complete overhauled painting etc.with your required charges. PL reply sir.
Halo sir I am write Kannada but conversation is Telugu. ಹರಿ ಪ್ರಸಾದ್ ಗಾರು. ನಾದೆಗ್ಗಿರ 1984 model ,yezdi ವುಂದಂಡಿ. Point set ನಿಂಕ CDI ಕಿ convert ಚೇಯಾಲಿ. ಎಂದುಕಂಟೆ ಸ್ಟಾಟ್ ಆವಡಂ ಕಷ್ಟಗಾ ವುಂದಂಡಿ. ಮೀರು ನಾಕು ಸಹಾಯಂ ಚೇಯಾಲಿಂಡಿ. CDI ಕಿ convert ಚೇಸ್ತೆ Different ಏಮೀ ಆವುದಾ. ದಯಚೇಸಿ Help ಚೇಯಂಡಿ.
सर मुझे आगे ओर फिछे सिग्नल लागणे का है तो वायरिंग कैसें करणा है मुझे बतवो डिटेलमे सर मेरा गाडी उस्के वझसे खडी है सर हिंदी मे बतावो मेरा व्हॅटसप न 8369816932 है
सर मुझे आगे ओर फिछे सिग्नल लागणे का है तो वायरिंग कैसें करणा है मुझे बतवो डिटेलमे सर मेरा गाडी उस्के वझसे खडी है सर हिंदी मे बतावो मेरा व्हॅटसप न 8369816932 है
सर मुझे आगे ओर फिछे सिग्नल लागणे का है तो वायरिंग कैसें करणा है मुझे बतवो डिटेलमे सर मेरा गाडी उस्के वझसे खडी है सर हिंदी मे बतावो मेरा व्हॅटसप न 8369816932 है
Tried it today, you are fantastic brother. Got the perfect sound of my jawa now. Turrr tutt tutt turrr.... Thanks a lot.
😀👍👍
Thanks for the initiative bro. After a long time found someone who provide videos for jawa and yezdi.
😀😀😀😀
please save jawa yezdi..grate job.so many thanks to u..
Thank you
You are doing nice job for yezdi lovers
Thank you
hello Anna na deggara YEZDI 250B 76 undi ni videos chala help cheathunnai👌👌
Thank you
Hello from Lucknow Anna, your have explained it very well.
Could you also demonstrate the ways to power headlight via batteries only so that there would be no need to use that switch at the rear shocx and the point settings for advanced firing for that liveliness in the pickup of Yezdi and that stunning reverse kick which scares the kids away :D
Ok
Hari Prasad ji do you not need to set the point gap at BTDC after setting the gap of 0.4mm at TDC by bringing the piston down by 2 to 3mm then again set the gap at maximum0.05mm by rotating the complete stator to either left or right to increase or decrease the points gap respectively? This is the recommended procedure to set the ignition of Yezdi in the user manual.
Yes I know.
But I said only rough calculation.
Because again we start the bike and tune the beat also.
I am using strobe bulb to set the points.
Very well explained
Thank you
Very helpful video. Thanks a lot 🙏🏼
👍👍🙏
Nice Work. Your alternator looks brand new. Have you re-winded the motor ?
Thank you 😀
It is old only
Thans bro absolute information
You are doing just great!
Keep it up dude.
Super explained
Very useful bro
Very good video. Can u please make detailed video on complete wiring.
Ok sure 😀😀
Hello I am from Allahabad, UP. While adjusting the points is it not necessary to set the point gap at BTDC ( behind top dead centre) also? which is as per the manual should not be more than .05 mm.
Yes, it is.
I tried to do that but couldn't.
Manual says, stator should be rotated clockwise/anti-clockwise. However, when I try rotating the stator, entire point rotates along with it making no difference to the gap.
It is just ridiculous.
@chrispbacon5027 I am also from Allahabad and have been riding Yezdi for the last many years
I have never had any problem with setting the point or to be precise, the ignition timing. The correct process is to set the point gap at TDC, which should not be more than 0.45 mm. I use a ballpoint pen body to mark both TDC and BTDC. I drew a 15mm line with 5mm markings on the ball pen body.. When the DTC has been reached( by rotating the crank clockwise), set the point gap to 0.45 or less. The BTDC is selected by rotating the crank anti-clockwise to bring down the piston by 2.5 to 4 mm. which be easily achieved by allowing the piston to go down between 2.5 and 4mm by watching the marking on the ball pen.The point gap at BTDC should not be more than .05mm. If it is found less loosen the magnet screws slightly and turn the magnet to the left till the correct gap is set, on the other hand if the gap is more then turn the magnet( the complete stator) to the right. Then tighten the two screws. With little practice it becomes very easy. Just try it.
@@RammoyRay
I do the exact same thing, except I keep the breaker gap at 0.35mm at TDC. At fiting time (2.5 mm on the left to TDC), I keep the breaker gap 0.04 mm.
Even after doing all these, my Yezdi is giving me a hard time. It only starts backward (reverse).
I suspect that coiling is damaged. I am tired of this shit and I am going to convert it to CDI.
@chrispbacon5027 Brother, use a feeler gauge to set the gaps. I think they are less .
@@RammoyRay
That's what I do. I use feeler gauge, I have a set
Dear sir will you upload video how to set points perfectly step by step in jawa bikes.
very usefull vedios ur posting thanks
😀👍
Sir please make a video on how to get tyres of yezdi as 3.25-16 is not available easily and the wholesaler don't have this tyre size so please make a video on how we can fix tubeless tyres which can fix into yezdi
I have all genuine spare parts with me including tyres
Contact me on this number 9908220222
contact on 9420332425
During setting what should be the position of the piston
Anna Cdi kite fitting whirring confection ela cheyali
Dear Hariprasad, Do you have any video on how to repair and install front shock oil seal holder and service
I will upload that video very soon
Nice sir you talking English like me nice sir... You from where sir..
Mancherial
Telangana state
Nice video, Could you please post a video on how to install the accelerator cable
Ok
Dear Sir ,I had a JAWA model 1974 ,which by default I sold it on 2009, now after couple of years I was quite disturb for it's absence.Pl advice me if I get Jawa bike not yezdi, is it possible to get 2nd hand JAWA now a days and then can it be renovat with new original spares through you as you have displayed in the video with the fantastic new original colour(Red) .please reply at the earliest.
I have only spare parts for jawa yezdi and roadking
If I get any Jawa, I will inform you.
You can check on olx also
Sir, of you get for me it will be better, I am trying from my side also ,I just want to confirm that if I get then will you help to renovate it from your side.pl reply Sir
At present I don't have any bikes with me.
Mainly I am not interested in bike deals.
If I get any information about Jawa I will give you contact details of owner
Ohh that's great, thanks for reply..
Hiiii
Mere pass 1968 ki jawa hai
Ab uska ek problem aata hai
Uske ht cable me current hi nhi as rha hai
Sir please record a video on front shoker oil based ..I want to see that
Already 2 videos are there in my channel
मेरे पास राजदूत एक्सेल टी मॉडेल हैं, उसे इलेक्ट्रॉनिक बनानी हैं, कित्ना खर्च आएगा
Any timing for points system
Bro... How to work auto clutch....
sir video kb upload kroge point setting ka
Want to paint my jawa in hyderabad, kindlt suggest advice
+91 94415 15737,Laxman mechanic
Purani yezdi kitne tk mil jayegi
Bikes nahi hai
25000
Ekdam complite on condition m
Bro show how to set points of yezdi
I have subscribed already
Halo sir point setting & CDI ki enti Different. Nadi 1984 model yezdi classic ki point set undi . CDI ki convert cheya galama.
How to convert alternater to cdi bro do vidou
Complete CDI unit is available
9491220222
Thank u alot
nice
Thank you
Sir video Kb kroge point setting ka
कही मिलेगी क्या अभी ये बाइक
, I am not asking for deal, what I mean to say If get JAWA from my own, can you renovate with full complete overhauled painting etc.with your required charges.
PL reply sir.
Ya sure
How to install magnet in yezdi kindly upload the video
Ok sure
Halo sir I am write Kannada but conversation is Telugu. ಹರಿ ಪ್ರಸಾದ್ ಗಾರು. ನಾದೆಗ್ಗಿರ 1984 model ,yezdi ವುಂದಂಡಿ. Point set ನಿಂಕ CDI ಕಿ convert ಚೇಯಾಲಿ. ಎಂದುಕಂಟೆ ಸ್ಟಾಟ್ ಆವಡಂ ಕಷ್ಟಗಾ ವುಂದಂಡಿ. ಮೀರು ನಾಕು ಸಹಾಯಂ ಚೇಯಾಲಿಂಡಿ. CDI ಕಿ convert ಚೇಸ್ತೆ Different ಏಮೀ ಆವುದಾ. ದಯಚೇಸಿ Help ಚೇಯಂಡಿ.
Hello kahan se
Hi bro....u have any yezdi restored bike for sales
Hi
No I don't have bikes.
I have only spare parts
Bro how to chang manual to electronic alternate
Complete CDI unit is available
@@hariprasadkathyayani your adress
how to open maginet in yezdi..plz.....
From where i can get point generator for yezdi
Plzz give me link or something
No need to purchase new genarator.
If you have old genarator you can rewind it again like new
@@hariprasadkathyayani sir what about point
@@tejindersingh1893
Point
Cam
Condenser
All parts are available with me
9491220222
Boss how much the point price
I need can you send me
I will send the money
video upload nhi Kia abhi tk
Hai sir I want to yezdi roadking 1998 model bike front shocksobser
I have all spares for jawa yezdi roadking
Contact me on 9908220222
System ho sakta hota hai
How to fix point cam
Yezdi classic full restoration video is there
Check it once
Need tester o light bulb
Bro set this all but it starts
Do you have any idea about this
Hello sir.
Hi
Hi bro did you changed the phone number bro
Hindime banav bhai video
Ok
Sir ap ka address mil skta ha kya
9491220222
सर मुझे आगे ओर फिछे सिग्नल लागणे का है तो वायरिंग कैसें करणा है मुझे बतवो डिटेलमे सर मेरा गाडी उस्के वझसे खडी है सर हिंदी मे बतावो मेरा व्हॅटसप न 8369816932 है
Sir apka number chahiye
9491220222
@@hariprasadkathyayani bhai yezdi maine ye sub kiya par cutrrent problem hai
सर मुझे आगे ओर फिछे सिग्नल लागणे का है तो वायरिंग कैसें करणा है मुझे बतवो डिटेलमे सर मेरा गाडी उस्के वझसे खडी है सर हिंदी मे बतावो मेरा व्हॅटसप न 8369816932 है
सर मुझे आगे ओर फिछे सिग्नल लागणे का है तो वायरिंग कैसें करणा है मुझे बतवो डिटेलमे सर मेरा गाडी उस्के वझसे खडी है सर हिंदी मे बतावो मेरा व्हॅटसप न 8369816932 है