Take seed square cut the corner off the 90degree side about 3 1/2 in use any straight edge on flange side and speed square on pipe pipe don’t have to be level fit flange square with straight edge and speed square so much faster don’t forget two whole pins first tac . Are the good old square and tape method is good too
Jack Masse The flange on the opposite side is welded and should be square right?? Well just measure from the welded flange on for spots. The measurements should be the same. That's how you should square the flange being fitted 🤤
Why didn't someone tell him to level the pipe in the vice and then he could check if the flange is plumb on the face. He was using the ugly torpedo level as a spacer he could have used a tape measure for that. That would have wasted time too though.
I need help to have this job any suggestions any contractor or company in a hardworking person from philippines I’m currently working in sewer plumbing .... I’ll appreciate any help thanks a lot
I like the older dude giving him time. We coonasses would have messed with him so bad! haha! But, Darlin', There's the fab shop! Hurry up, son! haha! Good lord! Pepe! haha
Typical Steamfitters working. One or two watching and one working slower than fuck. Give all us UA guys a bad name. I don’t understand there mentality. As a sprinklerfitter we work at such a fast pace and when we’re on he job with steamfitters we look at them and shake our heads. I would have been fired if I worked at slow as them when i was an apprentice.
Soldador que se respete debe saber puntear las dos piezas en todas las posiciones y soldarlas también sin tener que cambiar la posición del tubo más el accesorio en ese caso la Brida. y lo otro el Tubero o medio Tubero es más lento que una Tortuga para armar un Carreto.
Right now I'm finishing up fitting nulka torpedo platforms on the uss Nimitz. Watching the riggers swing in your 32 foot 20k lbs platform in place that you've been busting your ass over and seeing everything tie in together...greatest feeling
I like how theses guys are actually teaching him and telling him he can do it and not just saying anything
Looking at this cuz I'm heading to job as pipefitter helper trying learn. As much I can
Jose Fuentes same man, idk wtf going on but fuck it hahahaha
same here idk wtf going on but fuck it right 😂
Same
Here yo!!!
Lmfao me too jaja I went today and they hired me 🤣 and I don't know what the fjck to do lmfao so here I am lol
Lol
Confidence, it will come. Still move like you have a purpose in life.
This is a prime example how students who graduate TULSA WELDING SCHOOL come out.
Appreciate it! I’m goimg for pipefitting so this is very interesting
No wonder texas plants always blow up lol
What’s up guy this slick Rick I’m still welding and enjoying it
someone get that man a stick ruler....
Great vid! Pepe's gotta be slingin and hangin some pipe by now!
Man that is one Big Vice!
hes fucking hitting with the hammer on the same side than the guy welded at , hilarious!
😂😂😂😂😂
Take seed square cut the corner off the 90degree side about 3 1/2 in use any straight edge on flange side and speed square on pipe pipe don’t have to be level fit flange square with straight edge and speed square so much faster don’t forget two whole pins first tac . Are the good old square and tape method is good too
oh man fuckin helper
Hey wey thats was 7 years ago how's that vato living today. Make another video
don't hammer face of flange homie, lol.
Unnecessarily fucked that flange up, yeesh. Took their sweet time being inefficient too
A bit slow.
You could this without having to keep moving the pipe.
The guy welding the flange on us just as bad.
Bad teacher!!! teach that helper how to read a tape measure. And use tape measure and square on fitting up them flanges a lot faster!!!!
CLARENCE C.B. MARTIN JR. the fuck you need a tape for if you have a torpedo and a hammer?
Jack Masse
The flange on the opposite side is welded and should be square right?? Well just measure from the welded flange on for spots. The measurements should be the same. That's how you should square the flange being fitted 🤤
Yeah that's what I'm saying.
Going to make another video where I’m at now 👍
Andale pepe show em what u got!!! Good video!! 👍😎
Hector Arguero is so freakin fast I' mean holy shit pop a wheelie Bra!👍🍁😉🇱🇷💪🏻😆
Why didn't someone tell him to level the pipe in the vice and then he could check if the flange is plumb on the face. He was using the ugly torpedo level as a spacer he could have used a tape measure for that. That would have wasted time too though.
Pepe rolled that pipe for the welder pepe you need to make him tack a knee you cant spoil those welders pepe
How is he getting flange level when the pipe is moving in the vice
Square
hey dawg we worked in Richmond for the rail road, my dad and i, ray garcia, nathan garcia
Nathand Garcia what up kid
y'all from Houston?
Tyrone CatKiller Kang fuck u
That first tack up should of had a level on the opposite flange. To make sure your bolt holes line up. But what do I know... local 67
Random lengths on flanges?
I need help to have this job any suggestions any contractor or company in a hardworking person from philippines I’m currently working in sewer plumbing .... I’ll appreciate any help thanks a lot
faaaaaarkthis aint no sweat shop
y did have to turn it... could he just square ti one time n tack , then do the oppiste side
ไม่ร้อนมือบ้าง หรือ เชื่อมแบบนี้
he didnt level back out the pipe after move his monster vice...
Square
I like the older dude giving him time. We coonasses would have messed with him so bad! haha! But, Darlin', There's the fab shop! Hurry up, son! haha! Good lord! Pepe! haha
Cajun. In broader terms nearly anyone from S. Louisiana. Ya din' know dat, Cher?
I ain't never seen no one lay wire like this before. I have to try it
Mike Hunt ñora fyxvo ovhovuubj l jpnnpñmjibp l vlbobouqzpd bebí i l.tkpe
Ese es bien trabajo cantando y trabajando donde firmo
What kind of welding helmet is he using?
Pipeline welding shield
green horns both of them lol
wow! real quick lay wire! nice!
Nambe bato u got a long way to go in this video
Good God Pepe!!!
What the fuck Pepe!!!
1 1/2" 300# SW A105, I'll betcha! Bet they're in Texas.
Magnetic level will help lol
He's two holing it
Typical Steamfitters working. One or two watching and one working slower than fuck. Give all us UA guys a bad name. I don’t understand there mentality. As a sprinklerfitter we work at such a fast pace and when we’re on he job with steamfitters we look at them and shake our heads. I would have been fired if I worked at slow as them when i was an apprentice.
In Iraq, I work a piper and take a $ 100 fee every day for 8 hours
so is that basically what a pipefitter do..
I would of been replaced hahah
Mere ko welding kaam pe hana he
todayy jr!!!!!!! lmao
Necesitas usar lentes ... el welder
Echele ganas primo asi se empieza nomas que no se le suba y se olvide como comenzo
This is what non union gets you
lol you union welders are a joke slow and play the system enjoy working 6 months out of the year. I've had x union welders that's the true joke.
@@wardaddy3249
Or you join government and become union while working all the hours you desire.
lol why did he roll the pipe
peoplesable1 lmfao I wondered the same thing!!!!! If he couldn't weld that easy ass weld right where it was sum wrong!!!! Lol
Welder doesn't like to back feed
If that welder would of tacked it right it wouldn't of rolled. Just sayin
Someone give him a hand fuck sakes
Made that so much harder than it needed to be 😴
Soldador que se respete debe saber puntear las dos piezas en todas las posiciones y soldarlas también sin tener que cambiar la posición del tubo más el accesorio en ese caso la Brida. y lo otro el Tubero o medio Tubero es más lento que una Tortuga para armar un Carreto.
This S&b ??????
S & B pipe fitters hard hats are green, blue is civil
Nice jobs
ive seen it all now
fucking turnaround on 1 fit. gah damn. lol.
Non-union at it’s finest lol
Wrong
Qué onda con la panza cervecera y los lentes de seguridad qué pedo
Eyeballin'
argan welding kaam he
Daamn
Tack it in position welder.
This type of work seems so boring. I'll stick to plumbing. It's more fast paced.
Right now I'm finishing up fitting nulka torpedo platforms on the uss Nimitz. Watching the riggers swing in your 32 foot 20k lbs platform in place that you've been busting your ass over and seeing everything tie in together...greatest feeling
Welder. Éntrale a los taquitos !!!
YOU EVERY ONE IS WORKING YOU ARE IN FACEBOOK LOL
hard to watch!!!
Ponte las pillas pepe
hey get off the phone maN YO ARE AT WORK WTF
welding jop work he
Easy money
ensenen la sold
dadura
lol
la estas cagando pepe
Pepe de pie feetor
.i angry welding kaam karta hu
እንዛመድ
non junion yob
doing good
SMDH pepe
What the fuck
Google
no good
Skilll so slow..
Lol too slow to be a true fitter
HELPER BREAKING OUT
Wtf
Piss pour performance
If your going ot insult someone please use the proper spelling "Poor" not Pour!
OK princess
@@Brenkeeno what’s your sorry ass doing these days Brock ass nigga 😂