hi, I use the "Turnigy nano-tech 1500mah 3S 25~50C Lipo Pack" for this mod in the video (I will put a link below), this is the biggest Iipo which I can fit into the blaster. if you want something that will fit easier, you can use "Turnigy Bolt 850mAh 3S 11.4V 65~130C High Voltage Lipoly Pack (LiHV)" or "Turnigy nano-tech 1000mah 3S 25~50C Lipo Pack" (link below as well), they will fit easily, lastly I made a video on fitting the lipo, you can watch my video on how to fit the lipo into the blaster as well (link below as well) hope these help :) links to lipos: hobbyking.com/en_us/turnigy-nano-tech-1500mah-3s-25-50c-lipo-pack.html hobbyking.com/en_us/turnigy-bolt-850mah-3s-11-4v-65-130c-high-voltage-lipoly-pack-lihv.html hobbyking.com/en_us/turnigy-nano-tech-1000mah-3s-25-50c-lipo-pack.html link to video: ua-cam.com/video/powlc4UZgV8/v-deo.html
Thanks man. As for the demolisher, I am not sure as I do not have one. I searched the images of the internal for the demolisher, it seems similar to the stryfe, chances are it may work (again I am just guessing here), but it will most likely require some work on removing some material. The important part of the mod is to make sure the gear for forwarding the pusher must be aligned correctly and the reach of the pusher is far enough. This kit is mainly design for the stryfe almost like a dropin kit.
I am sorry, I have no idea will that work as I do not have access to IMRs battery and I I do not have barricade. However if I am not wrong, IMRs are having 3.8 volt and will be 4.3 volt per battery when fully charged. If you use 4 IMRs, that will be 17.2 volt max when fully charged. With that in mind I don't think it will be a good idea to run 4 IMRs.
Hi, to fit the pusher motor gear box at the position I place, not much needs to be done. Note that the auto kit comes with a black piece which is suppose to attach to the motor gear box, however that piece will not fit, therefore you will not need that. At that location are some raise part, I remember I removed them with just cutters. I secure the gearbox with hotglue to the shell, as the gearbox itself is a 2 piece shell so if in the future there are problem with the gear, I believe I can still remove the 2 screw from the gearbox and remove the top shell of the gear box to access the gears/motor within, therefore I decided to hotglue the motor gearbox. hope this helps :)
hi, the switch I use for the voltmeter should be this: www.amazon.com/Icstation-Pin-Rocker-Switch-3A/dp/B071SD337F/ref=sr_1_4?ie=UTF8&qid=1502610078&sr=8-4&keywords=2+Pin+Mini+rocker+switch+3A it is a small boat rocker switch
yes you can use the wire that comes with the volt meter, I replace the wire for this build because I accidentally broke the wire which comes with the volt meter and I only have those wire at that time.
Hi, someone asked me the same question a while back, below was my replay :) As for the demolisher, I am not sure as I do not have one. I searched the images of the internal for the demolisher, it seems similar to the stryfe, chances are it may work (again I am just guessing here), but it will most likely require some work on removing some material. The important part of the mod is to make sure the gear for forwarding the pusher must be aligned correctly and the reach of the pusher is far enough. This kit is mainly design for the stryfe almost like a dropin kit.
I am not sure I understood your question, I assume you are asking how much does the blaster cost in the region I live in. I live in Singapore, this blaster's retail list price at around 59.90 SGD - 69.90 SGD depending on the shop.
I am not sure as I only started nerf blaster modding recently and do not own any rayven. looking at the picture I found on the web, the internal of a rayven is not that close to a stryfe (which the kit is designed for), I think it might not be that suitable.
This is gold. Looks like I need to order myself another XSW kit to do this to my Desolator. Haha!
fantastic work mate good to see ppl pushing the auto kit to other blasters
thanks :))
I was waiting for someone to do this, but HOLY CRAP that was fast.
damm. that's a sick adaption dude! good job!
Thanks :)
Nice. I am going to do this to my new desolators.
Nice! Have fun :)
I'm sorry if i did not catch this in the video, but what kind of battery did you use?
hi, I use the "Turnigy nano-tech 1500mah 3S 25~50C Lipo Pack" for this mod in the video (I will put a link below), this is the biggest Iipo which I can fit into the blaster. if you want something that will fit easier, you can use "Turnigy Bolt 850mAh 3S 11.4V 65~130C High Voltage Lipoly Pack (LiHV)" or "Turnigy nano-tech 1000mah 3S 25~50C Lipo Pack" (link below as well), they will fit easily, lastly I made a video on fitting the lipo, you can watch my video on how to fit the lipo into the blaster as well (link below as well) hope these help :)
links to lipos:
hobbyking.com/en_us/turnigy-nano-tech-1500mah-3s-25-50c-lipo-pack.html
hobbyking.com/en_us/turnigy-bolt-850mah-3s-11-4v-65-130c-high-voltage-lipoly-pack-lihv.html
hobbyking.com/en_us/turnigy-nano-tech-1000mah-3s-25-50c-lipo-pack.html
link to video:
ua-cam.com/video/powlc4UZgV8/v-deo.html
Tungsten EXE Awesome! Thank you so much.
good work! do you think the fullauto-kit will also fit into the demolisher?
Thanks man. As for the demolisher, I am not sure as I do not have one. I searched the images of the internal for the demolisher, it seems similar to the stryfe, chances are it may work (again I am just guessing here), but it will most likely require some work on removing some material. The important part of the mod is to make sure the gear for forwarding the pusher must be aligned correctly and the reach of the pusher is far enough. This kit is mainly design for the stryfe almost like a dropin kit.
Could I run this kit on 4 imrs, barricade motors for Flywheels?
I am sorry, I have no idea will that work as I do not have access to IMRs battery and I I do not have barricade.
However if I am not wrong, IMRs are having 3.8 volt and will be 4.3 volt per battery when fully charged. If you use 4 IMRs, that will be 17.2 volt max when fully charged. With that in mind I don't think it will be a good idea to run 4 IMRs.
C&T Nerf Mods I believe so
Hey there. Was the motor hard to mount?
Hi, to fit the pusher motor gear box at the position I place, not much needs to be done. Note that the auto kit comes with a black piece which is suppose to attach to the motor gear box, however that piece will not fit, therefore you will not need that. At that location are some raise part, I remember I removed them with just cutters. I secure the gearbox with hotglue to the shell, as the gearbox itself is a 2 piece shell so if in the future there are problem with the gear, I believe I can still remove the 2 screw from the gearbox and remove the top shell of the gear box to access the gears/motor within, therefore I decided to hotglue the motor gearbox. hope this helps :)
what are the specifications of the switch you used for the voltmeter?
hi, the switch I use for the voltmeter should be this:
www.amazon.com/Icstation-Pin-Rocker-Switch-3A/dp/B071SD337F/ref=sr_1_4?ie=UTF8&qid=1502610078&sr=8-4&keywords=2+Pin+Mini+rocker+switch+3A
it is a small boat rocker switch
thanks! also can i use the thinner wire that comes with the volt meter to attach it to the 16 gauge wire
yes you can use the wire that comes with the volt meter, I replace the wire for this build because I accidentally broke the wire which comes with the volt meter and I only have those wire at that time.
How is it holding up after all this time?.
so far so good, no issue yet, however I did not use it very often a few hundred rounds maybe
*drools* that's sexy....
would this work in a demolisher?
Hi, someone asked me the same question a while back, below was my replay :)
As for the demolisher, I am not sure as I do not have one. I searched the images of the internal for the demolisher, it seems similar to the stryfe, chances are it may work (again I am just guessing here), but it will most likely require some work on removing some material. The important part of the mod is to make sure the gear for forwarding the
pusher must be aligned correctly and the reach of the pusher is far enough. This kit is mainly design for the stryfe almost like a dropin kit.
Now just throw that 3D printed barrel adapter and that thing is super tacticool
Yes that will be cool :)
How much is the non modified gun pls
I am not sure I understood your question, I assume you are asking how
much does the blaster cost in the region I live in. I live in Singapore,
this blaster's retail list price at around 59.90 SGD - 69.90 SGD
depending on the shop.
Thanks I live in HK
I want one.. Do u do commission?
I am sorry, I do not do commission work.
awesome mod ^-^
thanks man :)
+Tungsten EXE i was asking my Self a question , this mod can be used for a rayven ?
I am not sure as I only started nerf blaster modding recently and do not own any rayven. looking at the picture I found on the web, the internal of a rayven is not that close to a stryfe (which the kit is designed for), I think it might not be that suitable.
+Tungsten EXE ok thank i will try :D
If u ever want to sell, let me know..
ok will keep that in mind. thanks.