Notice, No mic's just a ruler and OS caliper. Hand ground tooling and a rudimentary lathe on the large side. This was how machinists built the world we live in now.
@@donepearce In my youth I could work with a tape measure to a 1/64th occasionally less. Sharp young eyes and a well cared for tape that was never allowed to snap back and cause any streaching or damaging of the tip. Regular inspection as well. I was trained that way. Made others shake their heads in disbelief. Taught by the best to be the best.
I need to make that very thread for a big vice restoration I have on hold as my lathe will not cut that big, I also need to make a nut too with the same thread as both the shaft and nut are worn badly. nice work, now I know how to get a wider thread without using a very wide tool.
It is a Whitworth thread used in many hard used tools like the lathe, vices and other like minded things. If you have the machinists handbook it will give you all the info on hand grinding the tools shapes and depth, etc. Good luck. These are my favorite threads to throw on a shaft. Wide, deep and strong.
@@TomokosEnterprize yes they look stronger than most, problem is my lathe does not go lower than I think 5tpi, I'm considering adding an electronic lead screw to get this project finished.
Many small machines over time have made The bigger machines from small 3 inch tiny chucks to the big 10 foot chucks It took a little one to make the new and bigger ones. Analog to DRO. It was us that made it all happen.
Having owned my own shop for 40 years. Is now retired. Very entertaining to watch the old primitive work that used to be done. Nowadays you can just buy bar stock with acme threads already there. Metric or standard. Up to 2 inches.
Hard Core Old School! Navjot has very obviously forgotten more about machining than I will ever even contemplate knowing about. Well done. Subscribing.
Curious why you can repeatedly open and close the nut with the screw on lathe,but don't get messed up? what's the tips ? i think only the work piece thread pitch is the same or Integer index as lathe screw pitch can do like you . thank you !
Un mandril de 3 aútocentrante..y compre un punto giratorío....con ese punto fijo..hay mucha frición.....y compre un.calibrador..barato....ese un.peligro..amigo..veterano..
Revolving centre use bearing in the bearing little bit play then thread is Babling Thread is 2 TPI because They use dead center every Time cannot use revolving Center, you are doing practical You know about dead center Try it thax for watching videos Keep watching. Have a nice day my friend.
O amigo ai peca em muitos quesitos.Para que uma placa de 4 castanhas para usinar esse eixo..para que essa baita forças no aperto.contra ponta fixo, usinar sem usar algum oleo de corte.Sinto muito mais isso não é exemplo.
Работа для 16к20.Поцентровал,поставил ершовую оправку,поджал ценром и вали хоть по 100 штук в смену.А это только для единичного производства.Баловство😂
@@ger1305 а у меня 33 г. стажа, но стаж тут ни при чём, если делаеш какую то одну деталь ( в основном), то другую начинаеш делать как начинающий , и потом - в любом случае есть какая то предельная норма времени выше которой никак не прыгнеш
Any child can do what you do. He could do the same with some training. You couldn’t do what he was doing even with months of training. He is skilled, you just push buttons.
Remember folks,....these people, this part of the world,...well,..they have nuclear weapons. Yep. Made them all by themselves too!.....yessir,....made ya cringe, didn't I?.......yeah, thought so.
This guy has no idea what it is to be a machinist, giving measurements with a compass speaks very badly of him, which means that his work is of the lowest quality. Although it can be seen that he can turn on that machine and half operate it, it does not mean that his work looks good in that type of places, quality is the least important thing, tightening the chuck with a lousy tube, the tool holders full of welding all a disaster
If you knew a little more you would realise it is the end product that matters, not how you got there! Many jobs don't require sub micron dimensions, especially if you make the mating part. If one only used the very latest machinery and techniques one would need to spend a fortune and some folks economies are unable to support such expense. Give the guy a break, it's not how I would work or perhaps even be allowed in some parts of the world, but when needs must, as they say.
Hello bro (compass used in a motion) vernier or micrometre cannot be used the machine is started you know the sir take care keep watching video thax for notice everything.
I've been a full time machinist for 23 years. I think this gentleman is doing one Hell of a fine job. I'd be very pleased to work in a shop beside him. It appears to me that his measurements and equipment are entirely suitable for the work he is doing.
Biaya akumodusi pengiriman BLOCK MECHINE dan FURING MECHINE : 1. Biaya akomodusi pengiriman FURING & block MECHINE dari MOSCAU ke Mongolia - Afganistan - taliban - kabul - Al jajair - new Denmark di tanggung masing masing ORANG PRIBADI atas namanya sendiri sendiri.❤ 2. Pengiriman FURING & block MECHINE dari MASCAU KE jepang dan Korea di tanggung masing masing orang dan atas namanya sendiri sendiri dengan masa waktu 13 thousand sampai 7628, THOUSAND FASE PERTAMA , 3. hari pertama dan hari kedua PEKERJAAN FASE PERTAMA selama 13 thousand sampai 7628 THOUSAND SELESAI DI KERJAKAN & paraf tanda tangan NOTA SURAT PENGIRIMAN Sebagai ARSIPARIS MESJIDIL MASCAU DI MASCAU RUSIA, sepanjang NOKTA tidak di lak di coret di hapus di silang di robek , 13 SD 7628 thousand 🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏
Notice, No mic's just a ruler and OS caliper. Hand ground tooling and a rudimentary lathe on the large side. This was how machinists built the world we live in now.
Absolutely.
yes... Poor quality...
@@peketee2278Better than I can do and my stuff outlast high quality broken parts I have to make.
I hate seeing slapdash work from "got the tee shirt" types. Measure properly with the best tools you have.
@@donepearce In my youth I could work with a tape measure to a 1/64th occasionally less. Sharp young eyes and a well cared for tape that was never allowed to snap back and cause any streaching or damaging of the tip. Regular inspection as well. I was trained that way. Made others shake their heads in disbelief. Taught by the best to be the best.
Good job ❤ I like it
Thanks 🙏
It's incredible that this man works like in the 1800s. Electronic vernier calipers are so affordable, I can't imagine he wouldn't be able to buy one.
Not as robust and would break. One of them might cost a months wages for him.
Wah ustad jj ❤
I need to make that very thread for a big vice restoration I have on hold as my lathe will not cut that big, I also need to make a nut too with the same thread as both the shaft and nut are worn badly. nice work, now I know how to get a wider thread without using a very wide tool.
It is a Whitworth thread used in many hard used tools like the lathe, vices and other like minded things. If you have the machinists handbook it will give you all the info on hand grinding the tools shapes and depth, etc. Good luck. These are my favorite threads to throw on a shaft. Wide, deep and strong.
@@TomokosEnterprize yes they look stronger than most, problem is my lathe does not go lower than I think 5tpi, I'm considering adding an electronic lead screw to get this project finished.
@@incubatork For sure. We can never have enough toys or tooling eh.
@@incubatorkcan't you add any other gears to get yor need ?
Many small machines over time have made The bigger machines from small 3 inch tiny chucks to the big 10 foot chucks It took a little one to make the new and bigger ones. Analog to DRO. It was us that made it all happen.
Wow big threand very nice work.
Thanks 🙏
Having owned my own shop for 40 years. Is now retired. Very entertaining to watch the old primitive work that used to be done. Nowadays you can just buy bar stock with acme threads already there. Metric or standard. Up to 2 inches.
Nice work 👍👍
Thanks
2 mouth thread ok sir good job sir
Single mouth thread
Acme thread, What is the application?
Very satisfying to watch 👍
Thanks
Which place
Very good 👍
Thanks 🙏
nice work
Thanks
@ 9:57 spitting at the workplace ....good gesture 👍
Hard Core Old School!
Navjot has very obviously forgotten more about machining than I will ever even contemplate knowing about.
Well done.
Subscribing.
Thanks 🙏
nice job
Thanks
Excilent work
Thanks for the visit
Good job 👍👍
Thank
Wow! You obviously know what you are doing.
Nice brother🇮🇩🇮🇩🇮🇩
Thanks 🙏
Nice work
Thanks
Curious why you can repeatedly open and close the nut with the screw on lathe,but don't get messed up? what's the tips ? i think only the work piece thread pitch is the same or Integer index as lathe screw pitch can do like you . thank you !
very good job
Thanks
Cara , não é melhor você comprar uma placa de 3 castanhas da China ? O preço é baixo e você para de sofrer para centralizar a peça🙂 !
Un mandril de 3 aútocentrante..y compre un punto giratorío....con ese punto fijo..hay mucha frición.....y compre un.calibrador..barato....ese un.peligro..amigo..veterano..
Very good brother form akbar sheikh ali engineaing works
Good job ji
Thanks
Very good
Thanks
Skilled one!👍🙏👌
@@shailendrathakar1755 Thanks 🙏
Good
Nice job
Sir thread time me machine disengaged karke manually back lane par slide kya tool threading me usi cut pr chalega ya nhi plss bataye
Great 👍
Thank you 👍
Too much so good
Very nice 👍👍
How do you change the gears for threads cutting
Square thread napane k liye alag pitch gauge hoti hai kya ?
சூப்பர் டர்னர் வாழ்க வழமுடன்
👍👍👍
Nice
Thanks
Which metal is this
@@GaddamDurgamma M.s iron
I need this work please if you can help me get the work
Don't mind my speech
Help me bro
can i get courses for one month sir
@@BinodMoktan-qp1jn yes
इस तरह की चूड़ी के लिए लिवर कैसे सेट करे ये बताओ
The impressive part is using a dead center in the tailstock. People don't know how to do that anymore.
Dead center can,t move anyway
Revolving centre use bearing in the bearing little bit play then thread is Babling
Thread is 2 TPI because
They use dead center every
Time cannot use revolving
Center, you are doing practical
You know about dead center
Try it thax for watching videos
Keep watching. Have a nice day my friend.
@@sunnysaini-z3k oui bon mais une pointe tournante en bon êta et mieux et ne chauffe pas
Like with Pakastani truck watching them weld and hand grind a hydraulic ram Im saying no friggen way then they reassemble it and it works
Nice video
@@RamaRao-n2k thanks 🙏
So nice
@@OppoA38-yv2xi thanks 🙏
Rough worker >> Fire him >> Seems to work with tolerances to the nearest Fence Post !
Amazing🎉
Thanks 😄
Looks almost like the opening to a rope thread.
2 tpi in inch
sir
@@sunnysaini-z3kRight! Looks good, sir.
Parnam sir ji keya mein bhi is kaam ko karna chahta hun kya sir ji mujhe ye kaam karne ko mil sakta hai
I love it
@@135sapkalaul Thanks 🙏
Micrometer ?????
What dose TPI stand for in 2 PTI ?
Threads per inch
Ya kardeş bunun için kepekli ayna kullanmaya ne gerek var
İmkansızlık desem zannetmiyorum
Very good too high stenless steel
Nice one
2 tpl thread wheel A B C D SIZE PLEASE
O amigo ai peca em muitos quesitos.Para que uma placa de 4 castanhas para usinar esse eixo..para que essa baita forças no aperto.contra ponta fixo, usinar sem usar algum oleo de corte.Sinto muito mais isso não é exemplo.
Good👍
Thanks
Goodinstalmentsir
Jajajaja.
Bien entretenido este vídeo.
Sin instrumentos de medición
Usando limas, le dan el acabado.
No prueban la tuerca.
You're cutting a square thread with a high-speed tool and you're not using cutting oil or coolant fluid? I find that pretty unusual 😉
Oil and cutting fluid are expensive.
@@aquilifergroup I hear you, they ain't cheap this days. 👍
I would really like to contact you if its ok by you sir am a kathe machine operator
i have a unimat sl 100. i think it will be hidden behind your workpiece
Работа для 16к20.Поцентровал,поставил ершовую оправку,поджал ценром и вали хоть по 100 штук в смену.А это только для единичного производства.Баловство😂
по 100 штук в смену, а чё не по 1000 - 😂 - ты прям быстрее электровеника
@user-vb3bp4xw1q у меня 30 лет стажа токаря.Если не понимаешь ,то и не говори
@@ger1305 а у меня 33 г. стажа, но стаж тут ни при чём, если делаеш какую то одну деталь ( в основном), то другую начинаеш делать как начинающий , и потом - в любом случае есть какая то предельная норма времени выше которой никак не прыгнеш
Uncle ji chak do phatte
Thanks bro
chaka pya fhatta bro
There is no need to tighten Chuck jaws like that on any part, let alone a tiny shaft.
He wasnt just tightening he loosened as well centering the work in a 4 jaw chuck
Dam koto porbe led mesin er
Que sofrimento do cacete! Eu já passei por isso kkkkkk hoje é mais simples
Well
@@SedekiaAlex thanks 🙏
الملزمة الظرف له ٤لقم سيء جدا للصنطرة ٣لقم كان افضل وهذه المخرطة قديمة جدا تبديل السرعات عن طريق القشاط بطريقة بدائية
Buy a dial indicator.
NO ONE spins the chuck on power when trueing up.
Wheel A B C D SIZE
Jajaja.
Qué entretenida, no😊❤❤😂
Centro gitatorio, calibradores, compaces,
micrómetros, y una gran Lima.
Con una botella, que desastre
Use live center instead of dead
❤❤❤
Szakmunkás szemszögéből finoman szólva csapnivaló
Quá ẩu máy mà lấy 🔨 đập
we want an order of turning job
I could make that on my DMG MORI in about 5 minutes without all the faff!
Any child can do what you do. He could do the same with some training. You couldn’t do what he was doing even with months of training. He is skilled, you just push buttons.
Threading wheel number send me sir
Daan Ako aajust tpi
Tiza en el nonius
Hostia que tornero
Remember folks,....these people, this part of the world,...well,..they have nuclear weapons. Yep. Made them all by themselves too!.....yessir,....made ya cringe, didn't I?.......yeah, thought so.
Un poco de taladrina
Very bad warking ❤❤❤❤
Toll to sahi laga le
Fírme,,poderôso 🧐
Уволить за нарушение техники безопасности.
а задний центр не крутится или мне показалось ?
Tupureler sən görən işin içinə
Ese cobalto es una mina
This guy has no idea what it is to be a machinist, giving measurements with a compass speaks very badly of him, which means that his work is of the lowest quality. Although it can be seen that he can turn on that machine and half operate it, it does not mean that his work looks good in that type of places, quality is the least important thing, tightening the chuck with a lousy tube, the tool holders full of welding all a disaster
It's very heavy duty
Sua opiniaõ é digna de respeito, na minha visaõ o trabalho dele naõ é taõ ruim assim!! Ok 👍
If you knew a little more you would realise it is the end product that matters, not how you got there! Many jobs don't require sub micron dimensions, especially if you make the mating part.
If one only used the very latest machinery and techniques one would need to spend a fortune and some folks economies are unable to support such expense.
Give the guy a break, it's not how I would work or perhaps even be allowed in some parts of the world, but when needs must, as they say.
Hello bro (compass used in a motion) vernier or micrometre cannot be used the machine is started you know the sir take
care keep watching video thax
for notice everything.
I've been a full time machinist for 23 years. I think this gentleman is doing one Hell of a fine job. I'd be very pleased to work in a shop beside him. It appears to me that his measurements and equipment are entirely suitable for the work he is doing.
Why on earth to they murder up the chucks so tight , bloody hell ???
Because it is very heavy thread ,so he fully tight chuck, you don't tight the
Chuck the pic go inside the chuck slowly, ( thax too observe the video .
Biaya akumodusi pengiriman BLOCK MECHINE dan FURING MECHINE :
1. Biaya akomodusi pengiriman FURING & block MECHINE dari MOSCAU ke Mongolia - Afganistan - taliban - kabul - Al jajair - new Denmark di tanggung masing masing ORANG PRIBADI atas namanya sendiri sendiri.❤
2. Pengiriman FURING & block MECHINE dari MASCAU KE jepang dan Korea di tanggung masing masing orang dan atas namanya sendiri sendiri dengan masa waktu 13 thousand sampai 7628, THOUSAND FASE PERTAMA ,
3. hari pertama dan hari kedua PEKERJAAN FASE PERTAMA selama 13 thousand sampai 7628 THOUSAND SELESAI DI KERJAKAN & paraf tanda tangan NOTA SURAT PENGIRIMAN Sebagai ARSIPARIS MESJIDIL MASCAU DI MASCAU RUSIA, sepanjang NOKTA tidak di lak di coret di hapus di silang di robek , 13 SD 7628 thousand 🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏
Just search "russian lathe machine accident" 💀💀
Good work
Thanks