I bought a 75in LG for $60 a month ago. I have been struggling with the display constantly freaking out but after watching your video, taping off the exact section you had, the majority of the issues stopped and it was usable, probably need to tape off another section to stop the problem entirely but I greatly thank you for posting this.
Thanks so much for the video. Saved me money for repairs! It was a lot of trial and error, so I had the colour issue people mentioned and I also had a lot of times where the strip of tv wasn’t working at all, just kept playing around with the electrical tape and finally it worked. Thanks again
after changing the smd resistors of my TV ks8000 these lines appeared, I did the procedure with the tape and now it works perfectly. thanks and congratulations for the video
Yes, we should start a BIG class action with Samsung !! My $5000 Samsung has the on/off looping issue just after 1 year and 4 months !! They said I need to pay more than $2000 to replace the panel !! So BAD !! Never buy again from Bestbuy and Samsung !!
I tried this fix on samsung q7fn. Jumping on the screen stopped. Awesome.. but there is loss of color and picture quality. There was improvement because jumping of the image made watching impossible.
I think the covering of some of the connectors pinout should be highly clarified, eg some voltage missing etc..though the problem got solved, we didnt realize the exact cause of those horizontal lines
I tried the same and I dont mind if the colors change, im colorblind, but my TV doesnt turns on correctly when I try to cover 2-4-10 Pins. Any ideas what I could try?
Mine had similar symptoms and turned out to be a shorted diode/filter ic on the panel driver board (located on the far right and far left). Found it with a thermal camera heating to 80c. Removed it and the flickering stopped, and tv works perfectly. Rather than blocking the short with tape you might be able to remove it
This fix obviously solves the image skipping problem, but it is tricked in the end, cutting off so many pins will not get a perfect image. In home conditions it can be repaired, 8 and 9 pin of the tape is enough to cut off then it does not jump and this is the maximum color that can be achieved.
*Thank You, you Sir have talent! Not only In electronics, also In making tutorial videos that are easily understood. Is there a way I can send you a short video of how my Samsung QLED Screen begins flickering when It has been on for 30 minutes or so? I shall look for your reply If possible. Best Regards From Texas!!*
Sounds like a temperature fault. Give it a try with freezer spray on suspected parts of the electronics. Maybe wiggeling the wires before could lead you to the right place.
Excellent presentation and Demonstration.very neat n upto mark repairing. thanks for video. One request the display which you show on top can be moved to side so we can read it very easily. thanks once again
So in other words that pins was there to mess up the image? 😂 I'm not sure that you really repair the TV... But you did get over with that lines on the bottom as we see
Notice that you did not get any response... It's just another magic tape video... which I would expect not to work. Somebody just copied somebody else's magic tape fix. Your question needs to be answered in order for any of this to actually be useful or applicable to anything.
@@n8lbv No, this is a legit fix. These are feedback lines, breaking the connection fixes the issue but affects the image quality as the board only gets the signal from the other working side.
Hi there I've done the same the line have stopped but half part of screen goes black and white Is there a solution for that. Could you please help me out on that problem
Sistemata una 65ks9000 curva stesso difetto, stesso punto della tua del video, i colori sono rimasti uguali a prima e non salta +, grazie infinite della dritta, un saluto da Napoli 💪💪
Ciao Riccardo, ho il tuo stesso televisore con lo stesso problema, un centro di assistenza Samsung mi ha chiesto €800 per il cambio del pannello... Dici che posso provarci? A distanza di tempo com'è andata?
Hi! First, big thanks for your effort, really appreciate it. I'm also an unhappy owner of a similar TV, QE55Q7F series in my case. One day, the picture showed black horizontal lines and desync in bottom part, thus I tried to cut off the pins as recommended. When cutting off the pins 1-15 (as in the video -- since I'm having the problem on the right side of the TV, the pins are numbered in oposite order there), the problem was solved, but the colors were washed-out (particularly red, which went to orange-brown in half of the picture). I tried to cut off every single pin one by one and found out, that cutting off the pin 3 is enough to get the picture without horizontal lines. However, even with this single pin cut off, the colors are still washed-out. :-( Please, do you have any idea, what to try next?
probably you need to change T-con board. In this case in video is also probably problem with same board, but issue is patched up by isolating some of the pins without significant picture degradation.
Hello, thank you for your video. I have the same problem but on 3/4 of the tv and not on 1/4 as on yours. Should I do the same as you or increase the amount of scotch? Thank you 👍
@@dragoslaur3962 Power lines?? These are logic lines, and this "fix" will result in working TV but with washed out colors and degraded picture quality on that half of the screen.
@@honestreviewsyoucanuse This is why there are feedback lines to begin with, every panel is different. On most you will see terrible contrast and very lacking color after doing this. You just lucked out with the panel parameters.
I have a QN55Q7FNAF TV. The right side of the screen is starting to detach, showing the white background screen. Do you have a video on how to keep the screen attached? Right now I'm using small clamps to do the job.
Another "magic tape fix video. Nobody ever explains anything about this. What is broken to begin with and what is covering associated pins actually do? There are so many combinations of pins that you could cover, how do you know which and how many to cover? And what is this actually doing? and how did you know what to do? And why does nobody ever explaining what it is doing? This sems to be a good video but nothing technical is explained or how you would have any idea what pins to cover or why covering pins mysteriously would "fix" anything. You are now missing signals that the panel needs or was designed to use. How is it working without them now? This makes no sense... And I do NOT have the same exact TV but have s similar problem. It would be helpful if I could understand what is being done at a technical level and why this video was posted. I would like to learn more.
You cover clock pins CK or CLK designation on board. The less pins you cover the better picture. Mostly is only one pin defective. It could be in LCD screen problem or in timing control board (T-CON board).
I have a qn65q80tafxzx it has practically the same problem. So i tried this fix. The jumping stopped but now a part of the screen has poor colors. Is there anything else I can do to improve picture quality.
@@oscarsanchezbc no jay nada uqe se pueda hacer. falla el driver. les pasa a todas las Q7F del 2017 y 2018. el video este es una solucion a la doble imagen pero te deja la tele sin colores y cn degradado de tonos. es decir una mierda de reparacion. de momento no hay solucion posible.
Great Job it helped me repair my own Screen... But a question thought why does the screen have a blue tint to it, I know the camera will make some screens have a blue tint to it but how do you remove that blue tint?
Thanks for the video. But Is it correct way to repair on permanent solution. If the dc power / signal stops by pasting plastic tape, might be corrupt another component ? Any circuit designers, please explain !!!!
Hi so i tried this and was able to fix the blurry horizontal lines, it worked well for a moment but now I have a vertical stripe on my right side of my screen please help
On my QLED 75 inch series 7, I'm getting these lines on the upper part of the screen. If I apply the same principle, do you think it will fix the issue?
@RepairAllTV have you ever managed to remove these fancey stainless bezel/trims seen at 15:42. Ive seen every trim & lcd removed apart from these premium models.
Hi I've tried using the same way as what you show but after i remove the film thing and switch back on the screen show blank with light screen light on. But if connect the film back and turn on display back on it. Like that i cant be able to see which having problem
I have a Samsung ue65KS7090 it has the flickering but only after some time heat makes it worse do you think it is still the same issue or could it be a bad part that I can replace?
hey boss, what's the name of the small metal part within the TV back panel - where you screw the screw to mount the TV.... two of mine broken.... need to get a replacement part
So the end of the ribbon contacts aren't used since the picture is complete but the lines are gone. I don't understand why part of the screen isn't missing at the edge since the contacts are covered by the electrical tape.
No, they are communication lines that get a feedback back to the board, blocking the faulty signal will affect image quality slightly, but will stop synchronization issue. This can be fixed a lot better by finding shorted out component on that driver board and replacing it.
Could the change of the main card BN94-11487J or BN94-12660J for QE55Q7FAMTXXC fix the problem. I tried your trick but I lost the brightness of color on the left side?
Hi, I have a QE55Q8, the model after that in the video. The jumping picture is the same for me. I opened it and used tape to cover the pins. Now it does not jump any more, but the colors on the 1/4 of the picture are very low. Nearly black and white. Do you have an idea how i can try to fix this ?
Hi man, do have tv 50“ which i damaged opening it on one corner. Now tv works but I see vertical and orizontal lines and have got two small black holes, one on the left lower corner and the other just 5 cm over this last one. Do you think guys I'd have any possibility to repair it diy? Thanks
I have a q6 it has a light glow in the corner of the screen it appears about a minute after I turn it on and depending what I'm watching it will wash out the tv you have any idea what it is I need help
@@RepairAllTV to change COF is to expensive? anyway thanx, it was same problem to me just on bit different model but it was nearly the same problem and it solved now by tape :)) and interesting how long that will last? what to expect for the future? because now i dont had time to use some in insurance and to not have tv for a long time 😂 so better DIY
@@WE.R.NOT.OK.W.U.TRMP_GTFO I'm not stupid, I was curious what they use in the video. I'm intending on making some for myself and foam filled cardboard will collapse under the weight of some of the heavy TV's with plasma screens. So what's the harm asking what these guys use? instead of reinventing the wheel so to speak!
Hi , I have Sony Bravia 52 inch LCD and now it's showing multiple horizontal color lines . Could you please let me know whether it will fixed or not. I asked in market and their response is horrible for me.
I have an issue with my 2018 samsung QLED 75” tv. While playing a game on it, the tv went dim, and shadowy lines developed on the horizontal axis. They are transparent and seem to be more intense where lines of text are involved. They show up all up and down the screen. I pulled back off and reseated all the ribbons, minus the small ones that connect to each LED column. No luck. There are 3 boards. The main board, the power supply board, and another one that has ribbons labeled “driver” and a number corresponding. I was told that this tv might not even have a t-con board, so not sure what the driver board is. Anyway, im hoping this isnt a display issue. Any advice?
It does not have a T con , it has Driver board , but they call them the same , its the board that drives actual screen , rest is power , and CPU . Did you get it fixed
I bought a 75in LG for $60 a month ago. I have been struggling with the display constantly freaking out but after watching your video, taping off the exact section you had, the majority of the issues stopped and it was usable, probably need to tape off another section to stop the problem entirely but I greatly thank you for posting this.
Thanks so much for the video. Saved me money for repairs! It was a lot of trial and error, so I had the colour issue people mentioned and I also had a lot of times where the strip of tv wasn’t working at all, just kept playing around with the electrical tape and finally it worked. Thanks again
Did you cover only one pin by trial and error to get rid of the line and also keep the colours?
Thank you very much for enlightening us with the repair techniques on various tv`s I have really gained a lot more. keep it up.
😂
after changing the smd resistors of my TV ks8000 these lines appeared, I did the procedure with the tape and now it works perfectly. thanks and congratulations for the video
Hello,
Can you tell me which resistors you have changed? I have an UE75KS8090 TV
The best video on smart tv screen.. Clear and genius explanation
This should be a class action. Every single model is affected by this eventually.
Mine did this shit this week and cant get it fixed POS never again screw samsung
Mine tv has lines in it as well. Samsung TVs suck
Yes, we should start a BIG class action with Samsung !! My $5000 Samsung has the on/off looping issue just after 1 year and 4 months !! They said I need to pay more than $2000 to replace the panel !! So BAD !! Never buy again from Bestbuy and Samsung !!
I need to replace my Samsung and I refuse to get another Samsung tv... Bought myself a LG OLED
Indeed
you cover some pins on the connector .Waht signal the screen is missing ?
how come there is no defect on the screen?
I tried this fix on samsung q7fn. Jumping on the screen stopped. Awesome.. but there is loss of color and picture quality. There was improvement because jumping of the image made watching impossible.
@@oscarsanchezbc same to me
@@oscarsanchezbc toda la razon del mundo oscar. se pierden los colores
I think the covering of some of the connectors pinout should be highly clarified, eg some voltage missing etc..though the problem got solved, we didnt realize the exact cause of those horizontal lines
I tried the same and I dont mind if the colors change, im colorblind, but my TV doesnt turns on correctly when I try to cover 2-4-10 Pins. Any ideas what I could try?
Mine had similar symptoms and turned out to be a shorted diode/filter ic on the panel driver board (located on the far right and far left). Found it with a thermal camera heating to 80c. Removed it and the flickering stopped, and tv works perfectly. Rather than blocking the short with tape you might be able to remove it
Thx for sharing👍
which diode did you remove, there are three of them. Is the TV working? Thank you
@user-ns2zp6te2s the one that was hot, they all can be removed and the tv should work. Its for esd protection
this is an easy at home fix for people that doesnt have sophisticate tools.
Your the greatest..
Just did the same to my tv and its 100 procent now 🎉
A durat mai mult demontatul/montatul decât reparatul. Felicitări... 👍
The boy full of sophisticated equipment. doing workaround
This fix obviously solves the image skipping problem, but it is tricked in the end, cutting off so many pins will not get a perfect image. In home conditions it can be repaired, 8 and 9 pin of the tape is enough to cut off then it does not jump and this is the maximum color that can be achieved.
*Thank You, you Sir have talent! Not only In electronics, also In making tutorial videos that are easily understood. Is there a way I can send you a short video of how my Samsung QLED Screen begins flickering when It has been on for 30 minutes or so? I shall look for your reply If possible.
Best Regards From Texas!!*
Sounds like a temperature fault. Give it a try with freezer spray on suspected parts of the electronics. Maybe wiggeling the wires before could lead you to the right place.
@@Mr.Smith_Mr.Wesson_andMe mine does same after 20 min has one one fixed it yet
Excellent presentation and Demonstration.very neat n upto mark repairing. thanks for video.
One request the display which you show on top can be moved to side so we can read it very easily.
thanks once again
So in other words that pins was there to mess up the image? 😂
I'm not sure that you really repair the TV...
But you did get over with that lines on the bottom as we see
I didn't think so either, that ribbon only needed unplugging and plugging in again and that would have fixed the tv.
Thanks, horizontal jump was corrected. But now the colors in the middle of the screen look dimmer (no color).
I have the same problem. Do you solved the Problem?
Yes, exactly this my same problem… can solve?
Brravo te qoft Respekt per ju 👍👍👍👍e kam me rregullu ni Display
E kam me rregull te Display shkruma ni mesazh WhatsApp 017680359693
Un mare like,eu sunt mereu alaturi de tine si activ pe canalul tau,imi place foarte mult ceea ce postezi si de aceea te urmaresc de atata timp.
Prima uitleg en het werkt. Mijn TV werkt weer als vanouds.
I fixed my QN55Q7FAMG thanks to your video, thanks you. Keep the good work
I'm glad you had success
Respekt zoteri ,qetash e nreqa nje tu ju falenderue videos tane.veq perpara
what contacts have you covered what are they for?
Information lines, this way it only depends on the other side of the screen, affects a bit the image but not that much
Как оказалось такой телевизор 65-дюймов, открыть одному это риск и нервы в первую очередь, было легче отремонтировать, чем открыть -)) ...лайк...
а как дефект проявлялся? Так же как в видео?
@@АндрейБоровиков-х1б 1:14 -1:30 видео , так он проявляется...
Excellent ! My TV 55Q broken this year. I Will go tô try this repair. Congratulations ! If my TV goes ok, I will return to answer you.
Did it work?
Look how far over the pins have made connect to the connector. Possible for the pins on the board to have moved over and shorted causing this ?
Thanks for sharing this... I like your job... 😍 i watch all your vedios.. You're clever an smart... From Syria .. GOD BLESS YOU 🌹
You forgot to put the speaker modual back in before you closed it up!
How do you know which part of the ribbon to cover up? Or does it not matter as long as part of it is covered?
Notice that you did not get any response...
It's just another magic tape video... which I would expect not to work.
Somebody just copied somebody else's magic tape fix.
Your question needs to be answered in order for any of this to actually be useful or applicable to anything.
@@n8lbv No, this is a legit fix. These are feedback lines, breaking the connection fixes the issue but affects the image quality as the board only gets the signal from the other working side.
well done , plz what's the names of the insulated signals, thx
Hi there
I've done the same the line have stopped but half part of screen goes black and white
Is there a solution for that.
Could you please help me out on that problem
Thanks for the video!! I fix a q7f 55" with the same problem
Did you have color problem after ?
Very nice job Bro! 👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍
Thanks 👍
Thanks so much for making and sharing this informational video.
Wow your a God of the tv repairs wow wow wow ive learnt so much watching your videos thank you for sharing.
Mushrik kafir
Sistemata una 65ks9000 curva stesso difetto, stesso punto della tua del video, i colori sono rimasti uguali a prima e non salta +, grazie infinite della dritta, un saluto da Napoli 💪💪
Ciao Riccardo, ho il tuo stesso televisore con lo stesso problema, un centro di assistenza Samsung mi ha chiesto €800 per il cambio del pannello... Dici che posso provarci? A distanza di tempo com'è andata?
Супер!Отличная работа. Но матрица замыкает, дай бог чтоб работала дальше!
Hi! First, big thanks for your effort, really appreciate it. I'm also an unhappy owner of a similar TV, QE55Q7F series in my case. One day, the picture showed black horizontal lines and desync in bottom part, thus I tried to cut off the pins as recommended. When cutting off the pins 1-15 (as in the video -- since I'm having the problem on the right side of the TV, the pins are numbered in oposite order there), the problem was solved, but the colors were washed-out (particularly red, which went to orange-brown in half of the picture). I tried to cut off every single pin one by one and found out, that cutting off the pin 3 is enough to get the picture without horizontal lines. However, even with this single pin cut off, the colors are still washed-out. :-( Please, do you have any idea, what to try next?
I have the same. Do you find solution?
I had the same issue. Any solutions?
probably you need to change T-con board. In this case in video is also probably problem with same board, but issue is patched up by isolating some of the pins without significant picture degradation.
@@zokonjazokonja T-con? What are you talking about... these models don't have a T-con for years. It goes straight to the logic board.
thank you I really like your videos it's a treat I say hello to you from Algeria.
Thank you for your good knowledge, great teacher.
Bravo excellent those screw less Samsung’s are a pain to get into
Hello, thank you for your video. I have the same problem but on 3/4 of the tv and not on 1/4 as on yours. Should I do the same as you or increase the amount of scotch? Thank you 👍
Мастер красавца трудяга спасибо что делишься сваим опытом👌
"Repaired". You keep using that word, but I don't think it means what you think it means.
That bicause he cut one power line ,the lcd is made with two power lines ,so will not last long this fix..
@@dragoslaur3962 Power lines?? These are logic lines, and this "fix" will result in working TV but with washed out colors and degraded picture quality on that half of the screen.
@@FrozenHaxorI used the same method and I see no picture loss 👍🏾
@@honestreviewsyoucanuse This is why there are feedback lines to begin with, every panel is different. On most you will see terrible contrast and very lacking color after doing this. You just lucked out with the panel parameters.
Thank you bosque...i am BETA from makassar indonesia
I have a QN55Q7FNAF TV. The right side of the screen is starting to detach, showing the white background screen. Do you have a video on how to keep the screen attached? Right now I'm using small clamps to do the job.
Another "magic tape fix video.
Nobody ever explains anything about this.
What is broken to begin with and what is covering associated pins actually do?
There are so many combinations of pins that you could cover, how do you know which and how many to cover?
And what is this actually doing? and how did you know what to do?
And why does nobody ever explaining what it is doing?
This sems to be a good video but nothing technical is explained or how you would have any idea what pins to cover or why
covering pins mysteriously would "fix" anything.
You are now missing signals that the panel needs or was designed to use.
How is it working without them now?
This makes no sense...
And I do NOT have the same exact TV but have s similar problem.
It would be helpful if I could understand what is being done at a technical level and why this video was posted.
I would like to learn more.
You cover clock pins CK or CLK designation on board. The less pins you cover the better picture. Mostly is only one pin defective. It could be in LCD screen problem or in timing control board (T-CON board).
Great video. Some english commentary would be great going forward. Liked & subscribed!
Don't you have horizontal lines since you block some signals?
super , une kam problem me Q700 , 8K , 65 dimensioni . me thone display - por po me kushtone me shtrenjet se vet tv ja , ke mundesi te me ndihmosh
I have a qn65q80tafxzx it has practically the same problem. So i tried this fix. The jumping stopped but now a part of the screen has poor colors. Is there anything else I can do to improve picture quality.
i think yo0u are covering some pins you shouldnt cover
@@Atipecomputers I was very careful to cover only the pins shown on the video. Do you have anything I could try?
@@oscarsanchezbc no jay nada uqe se pueda hacer. falla el driver. les pasa a todas las Q7F del 2017 y 2018. el video este es una solucion a la doble imagen pero te deja la tele sin colores y cn degradado de tonos. es decir una mierda de reparacion. de momento no hay solucion posible.
@@marcorosendahl7247 gracias amigo. Ya me deshice de esa tv. Salia muy caro remplazar el panel.
Great Job it helped me repair my own Screen... But a question thought why does the screen have a blue tint to it, I know the camera will make some screens have a blue tint to it but how do you remove that blue tint?
JUST INCROYABLE !!!
Nice toturial vedio and Good job sir..
you are the best !
After identify left or right side. Which side of flex cable should tape.
I wanted to ask if the problem with my TV are vertical lines, if I have to do the same procedure. Thank you
How to repair the QN55Q7FAMFXZA jumping picture?
Thanks for the video. But Is it correct way to repair on permanent solution. If the dc power / signal stops by pasting plastic tape, might be corrupt another component ? Any circuit designers, please explain !!!!
Thanks was gonna chuck my tv away managed to fix it that’s to this video
Hi so i tried this and was able to fix the blurry horizontal lines, it worked well for a moment but now I have a vertical stripe on my right side of my screen please help
thanks. Greetings from South Sulawesi
I have four separate ribbon cables from the t-con board . If I disconnect 1 I get no image . How do I know which one to choose from please?
On my QLED 75 inch series 7, I'm getting these lines on the upper part of the screen. If I apply the same principle, do you think it will fix the issue?
@RepairAllTV have you ever managed to remove these fancey stainless bezel/trims seen at 15:42. Ive seen every trim & lcd removed apart from these premium models.
Thank you for sharing. Very helpful. How about if vertical SINGLE LINE (green) in which I am experiencing right now. Appreciate...
Hello. my tv start like this but now its totally black screen- does the tcon need to replace ? or it still can be repaired?
RepairAllTV thank you
Hi, I did the same. The lines issue got resolved but the colours of that side are faded. What can I do to get all the colours?
Hi I've tried using the same way as what you show but after i remove the film thing and switch back on the screen show blank with light screen light on. But if connect the film back and turn on display back on it. Like that i cant be able to see which having problem
I have a Samsung ue65KS7090 it has the flickering but only after some time heat makes it worse
do you think it is still the same issue or could it be a bad part that I can replace?
Muy bien video bendiciones y saludos desde Oaxaca mexico
Congratulations brother, one question the time of garanty ??
hey boss, what's the name of the small metal part within the TV back panel - where you screw the screw to mount the TV.... two of mine broken.... need to get a replacement part
Thank you very much!! 🔥🔥🔥🔥
I wonder how long the tape method does it last ? Thanks
So the end of the ribbon contacts aren't used since the picture is complete but the lines are gone. I don't understand why part of the screen isn't missing at the edge since the contacts are covered by the electrical tape.
No, they are communication lines that get a feedback back to the board, blocking the faulty signal will affect image quality slightly, but will stop synchronization issue. This can be fixed a lot better by finding shorted out component on that driver board and replacing it.
Could the change of the main card BN94-11487J or BN94-12660J for QE55Q7FAMTXXC fix the problem. I tried your trick but I lost the brightness of color on the left side?
how many pins did u cover with tape ?
i tried the tape trick too it works but the tv lost color in the left side too. do you buy the replacement card?
I bought the card and it did not fix this issue
Ang galing nyo sir
How do I know how many connectors on the ribbon cable I need to tape over? I have a samsung un55ks8000fxza.
O shtet,panasonic tx-50ax802b. Ndalet ne panasonic logo. Ndonje ndihme? 👍
Hi,
I have a QE55Q8, the model after that in the video. The jumping picture is the same for me. I opened it and used tape to cover the pins. Now it does not jump any more, but the colors on the 1/4 of the picture are very low. Nearly black and white. Do you have an idea how i can try to fix this ?
Same here with the colour. Any help with the left panel colour issue?
What should I do My Samsung Tv QLED QA65Q9FNAk screen on and of Itself
How to fix a single vertical line which came right after changing a speaker, possibly opened my tv incorrectly, it's a samsung 55in curved TV
довольно простой метод подбора коротящих каналов, я так подлатал xiaomi 65es, который похоронили многие мастерские Москвы
Hi man, do have tv 50“ which i damaged opening it on one corner. Now tv works but I see vertical and orizontal lines and have got two small black holes, one on the left lower corner and the other just 5 cm over this last one. Do you think guys I'd have any possibility to repair it diy? Thanks
I have a q6 it has a light glow in the corner of the screen it appears about a minute after I turn it on and depending what I'm watching it will wash out the tv you have any idea what it is I need help
The flex contacts are there for a reason. Why would you block them ?
because there is a problem with (COF)
@@RepairAllTV This repair is no good, the colors will be degraded.
@@RepairAllTV to change COF is to expensive?
anyway thanx, it was same problem to me just on bit different model but it was nearly the same problem and it solved now by tape :)) and interesting how long that will last? what to expect for the future? because now i dont had time to use some in insurance and to not have tv for a long time 😂 so better DIY
danke für die video,ae hat funksioniert
Hi i'l do that already,but now just like the first the screen is a horizontallines what i do to fix it again thanks.
Great work sir
What are the blocks made from that you use to support the TV on the bench ?
for real, man? probably anything soft, like foam, or even Styrofoam packing material covered in tape, he loves tape. use your brain dude.
@@WE.R.NOT.OK.W.U.TRMP_GTFO I'm not stupid, I was curious what they use in the video. I'm intending on making some for myself and foam filled cardboard will collapse under the weight of some of the heavy TV's with plasma screens. So what's the harm asking what these guys use? instead of reinventing the wheel so to speak!
@@WE.R.NOT.OK.W.U.TRMP_GTFO Lee Kuan Yew, you think you are a smart ass?
I don't understand how that repair worked. Is it just me or did you forget to replace the speakers?
watching fr0m philippines
Hi , I have Sony Bravia 52 inch LCD and now it's showing multiple horizontal color lines . Could you please let me know whether it will fixed or not. I asked in market and their response is horrible for me.
first off all thank you ,
second i have samung 55q7f i have same probleme and i have smal video of my prob , can you help me ?
great job, and where were the speakers?
Speakers are in the black unit, at the bottom of the tv, he removes in the beginning.
At 11:32
Hey, I have a black line going horizontally across my Samsung led tv. Ive checked all the ribbon connectors they seem fine
Then it's the mother board in the center. If left and right are fine. It's the center..
Any video on how to fix qe55q7f 2018 ???
I have an issue with my 2018 samsung QLED 75” tv. While playing a game on it, the tv went dim, and shadowy lines developed on the horizontal axis. They are transparent and seem to be more intense where lines of text are involved. They show up all up and down the screen. I pulled back off and reseated all the ribbons, minus the small ones that connect to each LED column. No luck. There are 3 boards. The main board, the power supply board, and another one that has ribbons labeled “driver” and a number corresponding. I was told that this tv might not even have a t-con board, so not sure what the driver board is. Anyway, im hoping this isnt a display issue. Any advice?
It does not have a T con , it has Driver board , but they call them the same , its the board that drives actual screen , rest is power , and CPU . Did you get it fixed
Why is it so when you get a stripe on it that the picture is well?