I found an error in my trans tune. Correcting input tooth count from 25 to 39 allowed tcc to work with pcm command. It also allowed shift adapts to work curing firm shifts durring normal cruising.
The Whippled Riviera I did back in 2012 has that in its last pcm file, remember folks ya need to change the gear ratios for each gear if the pcm sees a ratio disparity it will change adaptives. I don't know if hp does but tiny does it. Sprocket ratio should also be 1:1 I've seen odd numbers from some 4t80e swaps lately, mostly seems to be hp folks. 3.11,3.48,3.71 are your Final Drive ratio. You still need to change each gears ratio as they differ. You can use the internal mode switch and wire it to the ext rage wiring. All logic outputs correlate
This is Amazing man! Thank you for putting this video out, I’m going to take it as a sign lol I’ve built boosted cars before but they are something i couldn’t afford to build now. I’ve been researching the 3800 and i like the fact that it’s something different and with a lot of potential. I kept finding that the weak links are the transmissions but this changes the game! I have kids now and i think a unsuspecting 4 door car thats boosted would be fun. I see gtps for about 1000 bucks with blown transmissions in my area. This combo could make for a really cool project that wont break the bank for us dads that still want to have fun. Thanks again!
I haven't watched this yet, but I use to pull these monsters out of Cadillacs in the early 2000's for a dealer in San Antonio. That was on a lift! Damn dude.....on the ground d.
Good more of you are finally seeing the 4t80e as our best option... You invert shift solenoid b with electromechanical or through the bin file? Tcc is easiest with a std tcc conversion system like those used with old school th350 to 700r4 retrofits
@@josephnowak Yeah, I used a small normally closed Solid state relay to trigger a 10 amp normally open solid state relay as my faster option to a NC wired 5 pin relay to invert the shift logic for solenoid b. I believe that grounding the 4t65e t c c switch in the PSM and disabling the code May allow me to use the 65e p c m to control the 4t80e tcc without an external work. I haven't gotten to test that method yet but I have high hopes.
Im interested in trying to get it to work. I took the vb off and and drilled the holes for a pressure manifold switch and adapted the harness but that didnt satisfy enough of the logic. Or at least it didnt make it work.
@@josephnowak I plan on trying to just ground the 65e tcc psm switch wire m try Mt ext or tu ne for any solution. Hobbs switch internal is next after lol
@@kylehalpren6203 lucerne is a different platform. The good news is that the 4t80 was used by gm on that chassis as far as i can tell. It likely wasnt used with the 3.8 though. Youd have to do some research on that end
Yes its doable. The 2000 trans is a little different from the 2005 that I have. The car is a little different than my 1998. Ls4king part 3 video goes into some of the controls, Very similar to 3800.
Is there a sort of write up for this swap process? I have an 03’ Monte Carlo SS that I plan to top swap and build, and I don’t feel like dumping a ton of money into a built 4t65e that could nuke upon its first launch. Let me know, thanks!
Chicago garage has a bunch of info in one spot. It is probably imo the best one. Its a known enough subject by now theres a bunch of fragmented infomation out there. I used ls4 king for some of the wiring and all data. Lots of work but worth it. I have also tried to answer comments completely for everyone as well
Fuckimg HEAR that my man i wanna fet my fucing shitty 4t6te out of my 06 ls monte. Im doing rocker body work some basic suspension and exhaust bla bla bla but after shes solid and inspcted and i habe the money and time THIS is my next move.
I have a 1992 Pontiac Bonneville and im tryna build. Engine already rebuild head gasket replaced. Everything. But im just trying get more torque power what do i need to two do?
I am not as familiar with the series 1 3800 which i assume your bonne has. Id look into the supercharged setup that would of came with the bonneville ssei models
Hey I have a 2005 Buck Century 3100….I was told that I have to get a transmission out the same car that I have(I thought that all Buick 3100 1997-2005 would be the same would you be able to tell me the difference) thanks a lot ……love your video 💪🏿
Big difference is the neutral safety switch on the early ones are on top and on the outside of the transmission. The later ones have the switch inside of the trans. 2004 2005 will have it on the inside. The later ones also had different type of solenoids if i recall correctly.
@@josephnowak ok thanks man that was very helpful…..I have another question what can I do to make my 3100 more powerful….i really wish they would have put a 3800 in the Buick Century’s
I am not sure on the ls4 tapshift. I know ls4 king has a lot of information on making these work on a ls4 car. His channel is what got me most of the information to get it to work behind a 3800
@@heathparks-i3d i think i used the output speed sensor out of the 65e only because the one on my 80 was damaged. If i recall both take the same delphi plug and looked similar. Its been 2 or 3 years since i plugged it all in.
The external switch i transfered from the original 65e. I ground 2 flats on the 80e shaft and repositioned the switch. Made some small tab brackets to hold the switch in place. Didnt have to extend factory wires.
I ran into this. I was told that to hook up what is available. For a while i drove w the 2005+ switch and through the course of debugging i had pulled the vb off and drilled the remaining holes to adapt the earlier switch. I grabbed a switch plug from a 4l60e and wired it in to where i thought that 3rd wire would go. Long story short a i never changed the input count in my file. Once i changed that everything worked. Although i havent tried it, i believe if my cal was correct from the beginning i would of not had to adapt to the earlier switch.
They are becoming more fequently used by turbo guys well beyond 350 wheel with stock internals. The advantage of doing the swap is the cost avoidance of the used high cost (discontinued) gmr parts. Gmr chain and gear set, input shaft and diff are thousands of dollars. A couple hundred bucks you have a working 80e core. The internet will tell me that an 80e on a supercharged setup is an overkill and not necessary. The cheap 7/8 conversion chain setups stretch and break in stock supercharged +e85 setups, seen it many times first hand and on tear downs
Could you give a bit of detail/tips on how you lifted your car to remove your engine/tranny. Looks like your a true diy and dont have acess to a lift like 90% of us shady tree mechanics
The shadow of the car is blocking the ramps i used under the rear tires. Use normal ramps - jack the rear up and slide them under each rear tire. I used an engine hoist to lift the car by the metal bumper. Theres a strap looped around the bumper - bumper cover can be removed for easier access. Theres a harbor freight furniture dolly underneath the engine / transmission. I set the car lightly (dont put full weight of car on dolly, engine oil pan barely needs to touch) on this before removing the subframe bolts. disconnect strut bolts, exhaust, tranny lines, electrical connectors, and steering from the knuckle. I may have missed some stuff but its doable on a smooth flat surface. Dont put your hands in there while the car is up. Pull it out from the side and i lower the car back down when everything is out, on jack stands.
BRO I REALLY MISS MY 2006 SUPERCHARGED CAR. I GAVE 2000.00 FOR IT WITH 123000 MILES ON IT, I PAINTED THE WHEELS ...I DID A LOT TO IT THEN MY GIRL AT THAT TIME TOOK MY CAR RAN IT IN A DITCH BLOWING THISE PASS SIDE TIRES AND RUINING THE WHEELS I JUST PAINTED, YOU CAN SE IT ON SALEM DOYLE 1500 SUBS, TELL ME WHAT YOU THINK ABOUT IT BRO, KEEP ON KEEPING ON BRO!!!
Man i did worong for the f16s in the airforce and i know how to build the jets wiring harneses but theparts where standardized and there was a technical manual. Im thinking i could do that part from scratch
I ended up sourcing the connector bodies and terminals and sealed relay from ballenger motorsports and assorted wiring colors from amazon. The other way is just extending what you have and repinning. Depends on how you want to go about it and your budget.
I been hearing alot of stuff that my series III l32 engine I just got with a 4t65e won't work on my series II L67 and transmission pull cause its different. The engine will work but not the transmission. Seeing this video I don't believe it.
The changover year on the transmission for the 4t65 is 2003/2004 ish. Valve body electronics are different. Never tried to get that to work before. Might require some research to get them to work
Thanks for your comment. I think the thing i didnt explain is that there is no shift kit available for the 80e, so you have to make your own. The feed holes for 2nd and 3rd are drilled out. It would probably be tamer w just an unmodded separator plate. One of the key pieces to making a 65e live is a gmr (gm racing) gear and chainset which you do not need for an 80e. Used they go between 2500 and 3500 dollars, its a discontinued item. Even then, a buddy of mine broke a used chainset on 18psi turbo car. The car was leaned on a lot but still.... Thats a lot of working jy 80e transmissions.
Thanks JN. Seems to me that if you want over 300 hp it makes more sense to get a RWD car. The later GTO's were about the size of your car and had essentially Corvette running gear. So way less cutting, hacking, and custom fab work involved to get any hp number you want. But i appreciate your motivation.@@josephnowak
Typical working core is 200 to 300 last i checked. It depends on what your working on or trying to do. The rwd stuff can get expensive too but there is potential to be faster. With this setup i just want to be able take it out and not worry about immediately breaking. Im a big fan of rear wheel drive stuff too
Hey I see you made a 4t80 work on a p04 pcm. I T’d off of pin E and connect that to pin U. Im having trouble getting mine to work properly. I have a 3800 mated to an all stock low mile 1995 4t80. It’s actually in an N body running on 4t45e calibration so the shift logic should be correct. Although i do know how to change it. I changed the iss count to 39 and changed the gear ratios. Not sure if i have the pulse per mile correct thought. Mine is the 3.48 fdr. I have dhp and am fairly proficient with the bin file. The issue im having is that in “D” it will only shift 1-2. In “3” it will shift 1-2-3. In “1” it will actually still shift 1-2. Im also in Wisconsin! An help would be much appreciated. Messaging me on messenger is cool too. Gauge Dochnahl.
@@Gawge1 pulses / mile should be based off tire size. I had to do some reverse math and google searching but i believe the tooth count for the output speed pickup on the diff is 31 teeth. Do you know what you entered for pulses per mile? What is your tire size?
@@josephnowakright now its just on a stock size 205/65R15 just to get it rolling but its going to be a 275/40R17. Eventually that will change again to a 15” slick when i buy some. Still not sure that this is my issue though but worth a shot.
@@Gawge1 il sent you the math in messenger. I suggest dialing in the tire size and go from there. These fwd pcms are finicky. My tuner and I had to do several iterations on hpt to get mine to work. Starting point for the 205 - 24518. Starting point for 275 - 24327.
I found an error in my trans tune. Correcting input tooth count from 25 to 39 allowed tcc to work with pcm command. It also allowed shift adapts to work curing firm shifts durring normal cruising.
The Whippled Riviera I did back in 2012 has that in its last pcm file, remember folks ya need to change the gear ratios for each gear if the pcm sees a ratio disparity it will change adaptives.
I don't know if hp does but tiny does it.
Sprocket ratio should also be 1:1
I've seen odd numbers from some 4t80e swaps lately, mostly seems to be hp folks.
3.11,3.48,3.71 are your Final Drive ratio. You still need to change each gears ratio as they differ.
You can use the internal mode switch and wire it to the ext rage wiring. All logic outputs correlate
Going to pick up a 4T80E this week for my build. Always good to see another video come out on this swap to save for later viewing!
This is Amazing man!
Thank you for putting this video out, I’m going to take it as a sign lol
I’ve built boosted cars before but they are something i couldn’t afford to build now.
I’ve been researching the 3800 and i like the fact that it’s something different and with a lot of potential.
I kept finding that the weak links are the transmissions but this changes the game!
I have kids now and i think a unsuspecting 4 door car thats boosted would be fun.
I see gtps for about 1000 bucks with blown transmissions in my area.
This combo could make for a really cool project that wont break the bank for us dads that still want to have fun.
Thanks again!
3.11 gear ratio? The 95 STS trannies had 3.73 posi in them.
Lockup using a floor mounted headlight switch is a great idea!
Performance shift button would be even better!
Finally seeing this, makes me so happy. Great work man.
Thank you for commenting.
I haven't watched this yet, but I use to pull these monsters out of Cadillacs in the early 2000's for a dealer in San Antonio. That was on a lift! Damn dude.....on the ground d.
Wow, this takes me way back. For my first car, my choice was narrowed down between a GTP or Thunderbird SC.
Good job on that swap.
Man thats cool cant wait to start mine
Very informative! Great vid!
Very good session ��🦮
Very cool video, thanks
Thank you sir!
Wow
Good more of you are finally seeing the 4t80e as our best option...
You invert shift solenoid b with electromechanical or through the bin file?
Tcc is easiest with a std tcc conversion system like those used with old school th350 to 700r4 retrofits
I did the solenoid method. I didnt know of the other way at the time. Maybe in the future il get rid of the solenoid. So far works good
@@josephnowak Yeah, I used a small normally closed Solid state relay to trigger a 10 amp normally open solid state relay as my faster option to a NC wired 5 pin relay to invert the shift logic for solenoid b.
I believe that grounding the 4t65e t c c switch in the PSM and disabling the code May allow me to use the 65e p c m to control the 4t80e tcc without an external work.
I haven't gotten to test that method yet but I have high hopes.
Im interested in trying to get it to work. I took the vb off and and drilled the holes for a pressure manifold switch and adapted the harness but that didnt satisfy enough of the logic. Or at least it didnt make it work.
@@josephnowak The 4t80E never had a tcc psm switch, youkinda have to use a hobbs switch plumbed internally to the tcc pressure or exhaust.
@@josephnowak I plan on trying to just ground the 65e tcc psm switch wire m try Mt ext or tu ne for any solution.
Hobbs switch internal is next after lol
Sounds good
What kind of cv axles did you use?
I used 661172 and 661327 cardone axles. They come out of a factory application.
Will this work for a 2006 Lucerne with 3.8
@@kylehalpren6203 lucerne is a different platform. The good news is that the 4t80 was used by gm on that chassis as far as i can tell. It likely wasnt used with the 3.8 though. Youd have to do some research on that end
Very cool video
Thanks for watching!
I been wanting to this for years I need to do this to a 05 impala I found a 4t80e 2000 will it work on my 3800 la?
Yes its doable. The 2000 trans is a little different from the 2005 that I have. The car is a little different than my 1998. Ls4king part 3 video goes into some of the controls, Very similar to 3800.
Is there a sort of write up for this swap process? I have an 03’ Monte Carlo SS that I plan to top swap and build, and I don’t feel like dumping a ton of money into a built 4t65e that could nuke upon its first launch. Let me know, thanks!
Chicago garage has a bunch of info in one spot. It is probably imo the best one. Its a known enough subject by now theres a bunch of fragmented infomation out there. I used ls4 king for some of the wiring and all data. Lots of work but worth it. I have also tried to answer comments completely for everyone as well
Fuckimg HEAR that my man i wanna fet my fucing shitty 4t6te out of my 06 ls monte. Im doing rocker body work some basic suspension and exhaust bla bla bla but after shes solid and inspcted and i habe the money and time THIS is my next move.
@@josephnowakso if i get this transmission in i have to mess with the computer and data?
@@rosshopkins2063 yes. Hptuners or an old dhp setup. I have never used or seen tiny tuner but that could be an option as well.
I have a 1992 Pontiac Bonneville and im tryna build. Engine already rebuild head gasket replaced. Everything. But im just trying get more torque power what do i need to two do?
I am not as familiar with the series 1 3800 which i assume your bonne has. Id look into the supercharged setup that would of came with the bonneville ssei models
Which starter are you using ?
Factory starter for a 3800 from O reilys
I have a 05 GXP with a 3800 engine in it can I put the Northstar transmission behind it without doing all that modification
Youl need modifications. They dont bolt together or fit on the subframe without them.
Hey I have a 2005 Buck Century 3100….I was told that I have to get a transmission out the same car that I have(I thought that all Buick 3100 1997-2005 would be the same would you be able to tell me the difference) thanks a lot ……love your video 💪🏿
Big difference is the neutral safety switch on the early ones are on top and on the outside of the transmission. The later ones have the switch inside of the trans. 2004 2005 will have it on the inside. The later ones also had different type of solenoids if i recall correctly.
@@josephnowak ok thanks man that was very helpful…..I have another question what can I do to make my 3100 more powerful….i really wish they would have put a 3800 in the Buick Century’s
Unfortunately there isnt really an aftermarket for the 3.1/3.4 engines platform. Good engine, but just no easy mods available.
will the 4T80E work with the TapShift in the ls4 pontiac gtp?
I am not sure on the ls4 tapshift. I know ls4 king has a lot of information on making these work on a ls4 car. His channel is what got me most of the information to get it to work behind a 3800
what did you use for a speed sensor
@@heathparks-i3d i think i used the output speed sensor out of the 65e only because the one on my 80 was damaged. If i recall both take the same delphi plug and looked similar. Its been 2 or 3 years since i plugged it all in.
You could do this with an impala ss?
@@Richoffbowls if its got a 4 speed auto it should be similar.
Pilow switch on the newer transmission did you hook up those wires
The external switch i transfered from the original 65e. I ground 2 flats on the 80e shaft and repositioned the switch. Made some small tab brackets to hold the switch in place. Didnt have to extend factory wires.
I havent heard the term pillow switch before. I have the manifold pressure switch wired in.
So you just matched up the 2 wires on the 4t80e TFP switch with the gtp 5 wires on the TFP. Think only 2 match rest did what leave it?
I ran into this. I was told that to hook up what is available. For a while i drove w the 2005+ switch and through the course of debugging i had pulled the vb off and drilled the remaining holes to adapt the earlier switch. I grabbed a switch plug from a 4l60e and wired it in to where i thought that 3rd wire would go. Long story short a i never changed the input count in my file. Once i changed that everything worked. Although i havent tried it, i believe if my cal was correct from the beginning i would of not had to adapt to the earlier switch.
Oh ok cool. I thought it would work as is with Just the 2 wires trail and error. Long as everything else is hooked up it should.
Great job building a customized Pontiac Grand Am or Grand Prix
i live in kenosha wisconsin could this possibly for sale
No its not for sale
What oil pan did you use?
Factory stamped steel 4t80e pan
I'm hoping to get a 4T80E and a 3.9 or 3.5 to throw in some random vehicle.
I wish that combo would fit in my '88 Cavalier Z24
bet it would.
How strong can these trans be? Can they be built to handle a ton or power or just like 350wheel
They are becoming more fequently used by turbo guys well beyond 350 wheel with stock internals. The advantage of doing the swap is the cost avoidance of the used high cost (discontinued) gmr parts. Gmr chain and gear set, input shaft and diff are thousands of dollars. A couple hundred bucks you have a working 80e core. The internet will tell me that an 80e on a supercharged setup is an overkill and not necessary. The cheap 7/8 conversion chain setups stretch and break in stock supercharged +e85 setups, seen it many times first hand and on tear downs
Could you give a bit of detail/tips on how you lifted your car to remove your engine/tranny. Looks like your a true diy and dont have acess to a lift like 90% of us shady tree mechanics
The shadow of the car is blocking the ramps i used under the rear tires. Use normal ramps - jack the rear up and slide them under each rear tire. I used an engine hoist to lift the car by the metal bumper. Theres a strap looped around the bumper - bumper cover can be removed for easier access. Theres a harbor freight furniture dolly underneath the engine / transmission. I set the car lightly (dont put full weight of car on dolly, engine oil pan barely needs to touch) on this before removing the subframe bolts. disconnect strut bolts, exhaust, tranny lines, electrical connectors, and steering from the knuckle. I may have missed some stuff but its doable on a smooth flat surface. Dont put your hands in there while the car is up. Pull it out from the side and i lower the car back down when everything is out, on jack stands.
@josephnowak thanks! I had looked into getting a tilting car lift.. but that looks even sketchyer. I think an engine lift would be better
BRO I REALLY MISS MY 2006 SUPERCHARGED CAR. I GAVE 2000.00 FOR IT WITH 123000 MILES ON IT, I PAINTED THE WHEELS ...I DID A LOT TO IT THEN MY GIRL AT THAT TIME TOOK MY CAR RAN IT IN A DITCH BLOWING THISE PASS SIDE TIRES AND RUINING THE WHEELS I JUST PAINTED, YOU CAN SE IT ON SALEM DOYLE 1500 SUBS, TELL ME WHAT YOU THINK ABOUT IT BRO, KEEP ON KEEPING ON BRO!!!
Man i did worong for the f16s in the airforce and i know how to build the jets wiring harneses but theparts where standardized and there was a technical manual. Im thinking i could do that part from scratch
I ended up sourcing the connector bodies and terminals and sealed relay from ballenger motorsports and assorted wiring colors from amazon. The other way is just extending what you have and repinning. Depends on how you want to go about it and your budget.
I love to get some more information if willing . Lmk if I can DM you
Sure, fb messenger. Joe Nowak with the regal profile picture
I been hearing alot of stuff that my series III l32 engine I just got with a 4t65e won't work on my series II L67 and transmission pull cause its different. The engine will work but not the transmission. Seeing this video I don't believe it.
The changover year on the transmission for the 4t65 is 2003/2004 ish. Valve body electronics are different. Never tried to get that to work before. Might require some research to get them to work
@@josephnowak Found out its from a 05 grandprix. How different is the 04 impala SS HD from this one I have no idea. I may just use it.
As long as the gear ratios are the same. If ones a comp g and the other isnt then thats a problem.
Just swap in the HD diff as the gp is probably a 3.05 fdr non hd diff
Shifts sound firmer than a stock car. Wouldn't it be easier to just upgrade the 4t65 with better internal parts?😊
Thanks for your comment. I think the thing i didnt explain is that there is no shift kit available for the 80e, so you have to make your own. The feed holes for 2nd and 3rd are drilled out. It would probably be tamer w just an unmodded separator plate. One of the key pieces to making a 65e live is a gmr (gm racing) gear and chainset which you do not need for an 80e. Used they go between 2500 and 3500 dollars, its a discontinued item. Even then, a buddy of mine broke a used chainset on 18psi turbo car. The car was leaned on a lot but still.... Thats a lot of working jy 80e transmissions.
Thanks JN. Seems to me that if you want over 300 hp it makes more sense to get a RWD car. The later GTO's were about the size of your car and had essentially Corvette running gear. So way less cutting, hacking, and custom fab work involved to get any hp number you want. But i appreciate your motivation.@@josephnowak
I guess the 4T80's are cheap since nobody is looking for them or know they exist. But if a 4L80 hits a salvage yard it is gone before its cold.
Typical working core is 200 to 300 last i checked. It depends on what your working on or trying to do. The rwd stuff can get expensive too but there is potential to be faster. With this setup i just want to be able take it out and not worry about immediately breaking. Im a big fan of rear wheel drive stuff too
Tried for a 10-second slip....shredded 11 4t65e's even with 9k$ in the trans (gmr/billet everything)
4t65e sucks
Hey I see you made a 4t80 work on a p04 pcm. I T’d off of pin E and connect that to pin U. Im having trouble getting mine to work properly. I have a 3800 mated to an all stock low mile 1995 4t80. It’s actually in an N body running on 4t45e calibration so the shift logic should be correct. Although i do know how to change it. I changed the iss count to 39 and changed the gear ratios. Not sure if i have the pulse per mile correct thought. Mine is the 3.48 fdr. I have dhp and am fairly proficient with the bin file. The issue im having is that in “D” it will only shift 1-2. In “3” it will shift 1-2-3. In “1” it will actually still shift 1-2. Im also in Wisconsin! An help would be much appreciated. Messaging me on messenger is cool too. Gauge Dochnahl.
@@Gawge1 pulses / mile should be based off tire size. I had to do some reverse math and google searching but i believe the tooth count for the output speed pickup on the diff is 31 teeth. Do you know what you entered for pulses per mile? What is your tire size?
@@josephnowakright now its just on a stock size 205/65R15 just to get it rolling but its going to be a 275/40R17. Eventually that will change again to a 15” slick when i buy some. Still not sure that this is my issue though but worth a shot.
@@Gawge1 il sent you the math in messenger. I suggest dialing in the tire size and go from there. These fwd pcms are finicky. My tuner and I had to do several iterations on hpt to get mine to work. Starting point for the 205 - 24518. Starting point for 275 - 24327.
You got a ig ?
Roaches2racecars