Crosman 357 how to rebuild
Вставка
- Опубліковано 5 вер 2024
- This video shows how to rebuild The crosman 357 Pellet pistol this is the older 357 not the new one that has the combat grips when one comes in for repair i will do a video for it, a few things are different in the new model.this one however is the paint ball version but it is the same gun just a different loader and barrel everything else is just a 357 pellet gun you can even use the pellet barrel and loaders in this same fram..
You’re still helping Crosman owners eleven years later. Thank you!!!
your welcome
Thank you for this video! My son opened up our bug-a-salt shredder air gun, making all the parts fall out 🤦♀. These instructions were exactly what I needed to rebuild it. It works perfectly again!
your welcome
My grandfather and I were checking into his old belongings, and he found this , and because he doesn't know English, he thought it was a toy , and gave it me . Now nothing works , almost, I tried dismantling it to see the problem and it works even less, wish me luck because I will probably never find one like this gem !
get your parts from ebay or airgun fourms can also help Crosman will also still have the diagrams as well for all of the guns they have ever made and still make
@@KevinMillard68 I managed to fix it completely with your help , even fixed the broken mill mechanism , thanks sir 😎
@@HistoricallyAccurate247 your welcome
Nice to see a "how to" video by a guy who actually knows what he is doing! Thanks much.
your welcome
had to fix a 357 today. took a half hour trying to figure out where the trigger spring goes😂. thanks for the help.
Glad to help
Thank you!!! Saved my Vigilante..I had issues with the seer and spring placement..They kinda migrated to the floor after I opened it up..Your video helped me get them back to their happy home =)
your welcome glad the video helped you
the oil will get shot out, but having a tighter valve spring in there could be part one of the lower power , and also if the valve was built along time ago then the stem seal could already be shot, run about 3 bottles threw it and see what happens.i never rebuild valves till its time to use them and i never replace the valve springs unless they need to be done, not sure where you got yours but it dont sound like your valve is operating properly,try what i mentioned and let me know.
I used the old valve spring in the new valve which made the plunger react like the old one. I also noticed that he valve tube had a smaller inside diameter so I used the old one also. The gun now has good power. Thanks for the advice and again thanks for the great video! Sorry to be so slow in responding but gun started to index poorly so I replaced the cylinder plate and index finger. It now works perfectly.
Great video! I ordered all of the parts from Crossman and they are very affordable. You can still get most of the parts from them. After watching the video I was able to replace all of the seals as well as a new valve assembly and a new piercing body. At under $20.00 I have a new 357. Thanks!
I have done lite work on air pistols - the barrel won’t stay locked - I guess it needs part 357- 021 latch support? The main thing is you can’t get it to puncture the c02. It doesn’t go deep enough to puncher the c02. I screwed it out everything looked good - screwed it back in till it bottom out and still did not puncher the c02.
you likey need a new pericing cap as well as the latch boot
@@KevinMillard68 Ok and Thank You.
Excellent video, thank you. This is going to really help. I just got an old Crosman 357 just like that one, I think it's about 8 or 9 years old. A friend of mine had it, and it doesn't hold gas, so he just gave it to me. I recently re-sealed my old 1976 Crosman 38T, but it is completely different internally (easier than this newer one). So this video really helps.
your welcome and happy to hear it helped you
@@KevinMillard68
Oh and by the way I just got another Vintage Crosman 357 Six Delivered Today, The Only Thing Wrong With It Is The Little Rubber Piece Under The Barrel Latch Assembly Is Missing So The Barrel Won't Lock But I Am Going To Order 2 Of Them In The Next Few Days. One To Repair With and One For A Spare. Just Had Another Vintage Crosman 357 Six Delivered On Friday December 8th.and 2 Vintage Crosman 38C's Delivered, One On December 6th and The Other On December 11th 2 Days Ago. I Got A Vintage Crosman 38T That Was Delivered On July 7th.
I Have Quite An Impressive Collection Of Air Rifles and Pistol, A Lot Of Them Vintage. My Favorite Rifles Being 2 Vintage Crosman 622's In . 22 Calibers and One Had Just Been Resealed and My Other Favorite Is My Vintage Daisy Power Line Model 889 13 Shot Pellet Pump Air Rifle That Had Just Been Resealed and It's In Mind Blowing Excellent Condition With Not A Speck Of Rust Or Scratch On It Anywhere. It Like Brand New and You Can Smell The Wood On It Fresh and It's In The Original Box, A Lot Of Them Are. I Wish It Was Some Way I Could Send Photos.
Thank You Again
Richard Oakley
12/13/2023 @ 8:07 p.m.
very helpful, do you by ay chance know where to get an 8" barrel upgrade for the 3576w?
THANK for your video, brought, old crossman 357, took it apart, one night, after watching your video, it back together.
Glad it helped
This video is very useful, and now I know where to get the seal kit, many thank's from Quebec, Canada!
your welcome
Ok...manage to find the kit. while installing it, i drop the gun....
I put all back together...and i ended up with one extra(!!!) spirng...
I think is the one you describe in 3.05 that its on the hammer..but i dont understant where excactly i have to put it...
The gun looks like working properly, but i didnt install a gas yet..untill get an answer for this....
Thanks
take a really good look at the video, for where the spring goes if all else fails goto crosmans website and you can download free print for the gun
KevinMillard68
;) Found it. Followed the diagram..and everything works just fine.
Very useful video for me...and good support also!!
This is an effective training video. I was able to reassemble my air 357 after springs popped off and it was a heap of parts. But, just a tip. If you have editing software, you could have flipped the image so that the viewer was seeing it straight on, not up side down. That would have made it easier to follow. Thanks for doing the video!
your welcome happy it helped
Hi Kevin: I took it apart again and found I had managed to lose the little spring that causes the trigger to hook up on the hammer when the trigger is pulled. I couldn't find it so dug through my "Misc Stuff" and found one similar that I only had to shorted a bit. The gun works great now so that was the culprit. I don't know how I managed to do it even after you had warned us not to lose it. Thanks again for sharing your expertise.
Best Regards,
rocky1405
cool good to hear you got her working. ya that tiny spring is a pain sometimes
your welcome and yes some of them are total nightmares this one is not to bad i have rebuilt lots of 357 guns
Thanks Kevin! Managed to get a 357 back together without your vid, but it was tricky. The exact same day I got the gun back together ANOTHER ONE came onto my bench! Oye!
Second one will need complete seal replacement. Have a set coming from Precision Pellet. Will have your vid bookmarked for reference.
Nice work!
Kris in NY
thanks man
I am happy to have found this video because it has helped me put my gun back together
your welcome
Thanks for the nice video,. Got my 357 back together. Ya tend to forget things when you take it apart. Your video was a great guide to getting it back together. Now, time to gas it up and shoot thru to ProChrono!
cool and your welcome
Thanks alot, I'm about to put one up on ebay and was checking for internal rust, and knocked something loose. I appreciate the vid, thank you! :)
It's 2 in the morning when I'm at that stage where I revert to childhood play and I was tinkering with the co2 storage, imagination amok. Out of nowhere I wanted to see what was inside, and so I unscrewed it and opened it. Holy shit, that was a mistake. it's now almost 6 and I've just now put it all back together. Mine is slightly different with the index bar, and minor other things, but good lord that was one of the most arduous and tedious and painstaking moments of my life. When things flew out at me when I opened it up, and then when everything else fell out later, I was so sad; I thought I had basically ruined it
+SoulDrawn yup yup they can be tricky
if your talking about the orings in the pipe they are not orings they are quad seals and are special type regular orings will not hold, get hold of alan at abairguns he can sell you a rebuild kit that will be proper for your gun you have to let him know if you have the new model with combat black grips or older model with brown grips for the proper kit
Thanks for the video. It helped me get my gun I had a teenager working again.
your welcome
well that could be a idea but if there is to much light then you get reflections off the metal pieces and that would not be a good,you could put the video into full screen and select 1080p hd and that might help you
Great Video! Thank You.
I have a Vintage Daisy Power Line Model 44 that I need to get back together, I have everything back the way it's supposed to be except for the hammer spring. It goes under the hammer first I think before you put the hammer back in but for the life of me I can't seem to get it in there just right.
Anyway you can get me to somewhere I can find out how to position that bad boy back in right?
I've got 3 Vintage Daisy Power Line Model 44's all together but I'm not going to take one apart to see if I can see how it goes because I don't want to have either one of those messed up.
The one that I am having trouble with is one that I purchased as is, saying that it was in working order but had to be put back together because they had ordered a new valve assembly and the hammer came out when they took it apart and couldn't get it back together right. I have put back together and built a Crosman 357 Six successfully basically just like the one you're showing here. The barrel latch assembly wouldn't latch and ordered a replacement and put a new one in.
all the guys i knew that fixed daisy guns all pass away now but you could check online pellet gun forms for someone that might be able to help you out there likey will be a few guys there on one or more of them
@@KevinMillard68thank you Kevin, I appreciate it.
I'm Sorry About The Loss Of Your Friends! God Bless Them All In Heaven!!! 🙏
I've lost quite a few Friends and Dear Friends and Ex Girlfriends and Sweetheart In The Last Fee Years Going On 3 Now and All Of My Dogs Have Passed Away Too. The Last One, Buddy, 13 Year's and 8 Months Left Me On September 25 2020 and The Next To Last One, Mr. King, 13 Year's and 5 Months On April 25 2019.
There Were Many More Going All The Way Back To 2000. I Got My First German Shepherd, Smokey, Back in 1990.
Thank You Again
@@KevinMillard68
Hey Kevin
It's Richard again.
Hey I finally got the 4 pack of seals to replace the old worn out seal's in my 4 Vintage Crosman 357 6's. One of them did not have the little dust screen under the piercing cap. I cleaned up everything and put the new seal in over the piercing cap and screwed the holder screw back on. I haven't tried it yet but I was wondering if it will work without the little dust screen in there?
Thanks
i never heard of it so i have no idea, i only use crosman pellgun oil or Sae 30 non detergent motor oil
Great video! Helped me figure out the parts I needed and made sure I got it back together right.
~Pierre
Im thinking abaut options several of them before parting with my cash, im not a repair tech- so im using an industrial type silcone lube with teflon like moto master 300- its not leaking from the co 2 port so plumbers teflon is out of the question- repair and return will probably cost me 23.00- so if the silicon lube does not succeed then im really interested in watching this and become a do it yourselfer like I've done in the past with my cars on occasions-
If you swap the valve for a more powerful one you can add a lot of power. Best mod you can do. Peace
there is no more power valve for the 357 but i do know the mod for the current valve the hammer spring can also be upgraded from the old style to the new one for more power as well
a little thank from FRance. My 357 is build. I will try it tomorrow. Thank you again for this video.
Nicolas
your welcome glade it helped
I have crosman vigilante almost same as this 357. This video helped me rebuild it because when I opened it all parts fall off. I'm missing that little brass piece what u put in that hole of hammer, is it important and do I need it? My gun works when I pull trigger and everything moves but I haven't tested it with Co2 because i'm afraid it gonna blow up and break gun or my hand.
+Allu if your missing parts then call alan at abairgun.com
my first shot is fine but then the rest of the "round clip" that the pellets are in become misaligned and won't shoot anymore. I have to manually fidget with the "round clip" to make it work. help.
you need a new Pressure plate and indexing finger
Not only Crosma uses that sort of valve (the ones you need that funky tool for). So does ASG. And also some Umarex guns
nice to know ,
I have a daisy powerline model 44 I’ve had it for three years old I want to bring back too
i dont fix airguns anymore and never really got into fixing daisy the only 2 guys i knew in canada that did are both passed away now so i have no idea who might still be working on them
Thanks i had a 40 year old crossman gun and it wasnt working an then all the parts fell out it was my dads fathers that was passed on to me
your welcome
Very nice video! You helped me solving a big problem in my crossman. Thanks!
your welcome
My revolver leaks co2 almost immediately after I tighten the cartridge. I don't know why it happened because it gave no warning at all. Do you think a seal kit will do the job? The gun has been well cared for, never dropped or mistreated.
if its just at the co2 bottle area then just put in a new end seal other wise rebuild kit
my near new Vigilante is not releasing gas when the trigger is pulled. There is pressure within the 2 cylinders I tried but it is not get through to the cylinder
they have crapy valves these days known problem crosman still has not fixed so just order in a new valve and your goof to go till it messes up again, if you pull the trigger enough times it will work fine again for awhile till its screwes up again i reallt dont get what the problem is yet with the valves i havea customer with the same problem and they only real fix is to find and older verison 357 valve and then your good to go for 20 years as well as its got good seals in it hard to find those valves tho i have one and they do go for big bucks when you can find them
Kevin I was wondering if there was anyway to get better volume out of the cylinders but I guess after watching this that it's preset, also I dripped mine out of the cabinet it was in to a cement floor about 4' and the barrel part jambed back to the cylinder pin I moved it back but it was way to easy to move have any idea's how to stabilize it?
Great video but camera was a but out of range for a good view.
Thanks for posting it it does cime in handy if I was to try to repair one I have two and what weight of oil is that your using? 10w?
no idea without having it my hands to see the damage that was done
did you get this thing brand new cause if you did then take it back if not then call alan at abairguns after 6pm his time and he can set you up my stock of 357 pats is really low right now and the parts you need i dont have in stock at the moment..
I rebuilted, and installed a new gas cartidge, without installing the cover plate, just to figure out where is the gas loss. Its definetely from the last point before pushing the pellet. So, something is wrong with the part that needs the special part to screwed back...
I fear I'm much too late, but thank you SO much!
your never to late to fix your own guns its getting the parts for the vintage ones thats the challange check ebay
AMIGO PARA FELICITARTE EL PRIMER VIDEO MAS ESPEFICIDADO QUE HE VISTO ESPERO TENER TIEMPO PARA VER TODOS TUS VIDEOS SA
thank you
Thank you very much, you save my revolver :D
Tobi en your welcome
your very welcome
I've had one for a few years just recently it stopped cycling the cylinder reliably. What would be a common cause of this? I used the old and new cylinder, the old one cycles better than the new one...
face place has platic pressure spring that wares out so get a new one and a new indexing prawl and you good to go just be careful not to disturb the seals in the pipe or youll be doing them as well
Have two of the "old model" .357 Crosmans, this will help a lot in their maintenance. Thanks. Who has the best "O" ring seals? Or do I find the similar sized "O" rings at the hardware store?
abairgun.com has the best kits and parts access even for the older crosman guns best to call him so he knows what version of the 357 you have they did make some changes over the years
Question Kevin, I have the old 357 "brown grips" but it was missing the parts in the c02 puncture area. The gun was my brothers and I wanted it fixed. I bought a kit off ebay that came with the new valve assembly prebuilt, just drop it in and screw case back together. He sold it as a kit for phase 1 and 2 guns, but I noticed it is for the newer guns. However I installed it regardless. It does shoot, but its only giving me a small percentage of power, not even enough to push a pellet out of the clip. I messaged the seller and he said it could be the hammer or hammer spring. I doubt that, I suspect a blockage in the jet or valve perhaps? I really want this old gun working again.
order in the parts for the original valve/gun from alan at abairgun.com dont ever but seal kits for any guns or older crosman guns off eaby always goto alan he is the best and has the proper parts . you might have gotten a bum valve and the newer valves SUCK rally bad. FYI never email him , call him only after 6 or 6:30 pm kanas time ..
Hi, I just bought a Crosman 357 gun and the problem is that, the latch support is missing! Also another problem is that the index finger spring is missing because it won't spin the cylinder! I don't know what those parts are really called so if you can help me figure out those names and website to order them it will GREAT.!
A friend gave me a crossman 357 to see if i could repair it for her. Your video helped me tremendously, but i was unable to repair it for her. How can i go about getting this to you look at?
you cant i dont repair airguns any more the cost of parts and labor make it unaffordable to people sp fixing it your self if your best bet but you can tell me whats going on and i can do my best to help you that way
I didn't realize and am seeing this was a video from 10+ years ago, so for that I apologize. Thank you for your assistance....
So I took apart the pellet gun because it just leaks. Assumed it was the seals so I have them ordered, but in not sure why as soon as you puncture the co2 nothing stops it.
2nd issue, the pellet magazine if you will, doesn't spins. I can seem to find that part listed. Any ideas.
thanks and your welcome glade the video helped you out
Well it is a vintage one,and has a custom BSA log barrel. I live in Alberta so I would be looking at 100cdn?
your looking at 54.00 for the basic rebuild kit this will not include a new face plate or indexing prawl which i advise strongy to do + 35.00 labor and shipping costs both ways iam in ontario there is no mark up on the parts i dont make anymoney on the parts at all. it takes about 2 weeks for me to get the parts ,, crosman canada wont have the parts for vintage guns, so i have to get those parts from the USA and before i can even order in the parts ihave to know which version of the gun you have of the vintage series there was changes made to the linkages for the trigger as well as the indexing prawl as well. so that now adds more time on getting it done and back to you..
What is the thing that the air goes thru called mine is not keeping the air in the cartridge when I screw it in it leaks in the gun and I just got it from my older family member and it is still very nice and will should just don't hold the air.
end seal for teh co2 bottle and there is also 2 quadseals that leak as well ,, my advice get a full rebuild kit from abairgun.com and rebuild the valve and all the seals and might as well get a new hammer spring as well and she will be just like new again
Thank you very much
I forgot to ask. If you recommend a seal kit which kit would you recommend. I believe that with your video I can take it apart & reassemeble. Thank you
you just need a 357 complete rebuild kit
Hello there! Thanks for your sharing. I own a ASG chromed, 6 Inc. Dan Wesson Model 715 replica. It is new. I fear that one day something wrong comes up... 😮. As I love guns and as I can not own them here, I turn myself to the replicas...Parts are expensive and not always easy to get here. 😢. I do not know how you can disassemble that one, and put everything back together... I wish I could do that too... I freeze only by thinking that one day this may/will happen...
just takes getting into it and a teardown diagram helps then once you ha ve done it a few times its easy and a walk in the park
@@KevinMillard68 Thank you again for taking your precious time awsering me! This along with your incentive awser is quite important to me. Best reggards from Portugal!!
good to hear
yup you can power mod it for a bit more fps how ever the best thing for power and keeping it legal is find your self the 8 inch barrel for that gun it will take the gun just so very shy of 500 fps , as for small game it wont take much more then some chipmunks and some small birds.
What sort of paint should one use on one of these for touch ups to match the color as best as possible?
I dont do little fixes i strip all the paint off and redue it complety youll never get a match of any color to blend right
i have a colt cybergun 357 python, i took it apart to fix it because the trigger was stopping halfway, now i cant put it back togeather and its so fustrating. pls send help
cant help sorry dude
i would be interested in your services. do you have an email where i could send you more details??
Hello I have a older model 357 that was passed down to me. It needs a new seal is there any where I could get one pre built before I order a seal kit?
So my gun's barrel keeps on falling down because the latch support is gone!
Awesome and very informative video thank you. i'm pretty sure i'm going to have to get a seal kit. Where do you get those from?
thanks any where that fixes crosman airguns including crosman or you can also see alan at abairgun.com as well
Thanks this helped a lot although my model is slightly different I got it to work again.
your welcome
yup new and old models no problem
Hi sir!
Thank you for your video! I have and old 357, with the 8" barrel, brown grip. It started to leak at the top of the CO2 bottle once screwed in. I've just sent an email to ABAirgun for some info on how to proceed to get my gun repaired. I'm from Canada.
Thanks again for sharing this video/tutorial.
Take care.
your welcome
cyou change the barrel on this gun
can you tell me which barrels you can put
In the barrel there is a plate that has looks like a keyhole it came out
take out the barrel slid the metal plate in at same time incert the barrel in the key hole easy to do
Kevin, I just purchased one of these guns in the original box. It has one issue. The rubber piece thet supports the latch for the barrel is not working i think it is dried out. Do you know the part number or where I might get one? Thank you for your help. Brad
Brad Hinz its called a latch support boot and you can order them from any crosman repair depo or call alan at abairgun.com
this is great but the assembly you installed for the seal where the co2 sits, mine leaks, can this be repaired without the tear down?
its tricky but yes
Thanks for the great video. Thanks to your great step by step instructions my rebuild was easy. One thing I have noticed though, is that my gun seems to have a little less power than before. My seal kit contained the complete valve and CO2 inlet assembly and the plunger is stiffer than my original. Also there was a lot of oil in the valves. Would these affect the power? Again thanks for a great video.
is there any differance between a 357 and a 357-6. the 6 means it's a six shooter that can also accept the gray 10 shot wheels. I still can't find the faceplat for it(357-035 is wrong). I can't measure the inside diamater of it and see what the new 1 is and figure out hot make it work. any suggestions.
the difference the barrel length for the most part but there are differecnces inside the guns when they made internl changes otehr changes made was the nozzle spring
guess when i get the money i'll have too buy the 357-050 and hope it fits in the cavity
I have a 1357 that function fine with the exception of the latch that hold the gun together after loading. There is not enough spring tension on the latch. How can this be repaired? thanks.
you need to replace the latch support boot
@@KevinMillard68 With a bit of research, I found the wedge online. Pretty pricey for what it is!
Hello Kevin. Great Video. Thank you. I think the latch support boot wedge fell out of mine. Have you ever seen that happen? Any recommendation of a replacement part for it? I could probably get creative about wedging something in there if necessary. Very helpful to see how it was designed in your video.
never seen one fall out but they can dicenagrate for sure and you can order in a new one from crosman just carfull when you open the gun if you pop either one of the quadseals on the brass pipe out youll need a new set of thoes as well
@@KevinMillard68 thanks for the quick reply. Havent used it in a long time. Went through first clip great, accurate. Reloaded and the latch lays flat. Mine is an older model, hopefully the wedge is the same.
google abairguns that will get you to his website with contact info and no you cant call him this late at night.just tell him what parts you need and he will know you will by the way also need a new set of quad seals .
I am just replacing the latch on top, will that mess with the seals when I split the main body?
only way toi know is to take it apart do your thing and see what happens its a crap shoot if the pipe seals go or not just make sure to losen off the co2 bottle ring before you remove the cover other wise stuff might happen that you dont want to happen
The latch on my gun does not latch! I think the latch support is missing. Can that support be purchased and can it be installed without taking the gun apart? If not, where can I send it for repair and what is the cost?
+joseph bourque you can buy the latch support boot seperat yes and your old one is probely still in the gun just worn right out ,. and yes the gun must come apart. if you live in the U.S then send it to alan at abairgun.com if you live in canada find your nearest repair centre if and only if its a new version 357 if its and old school one then you need to send it to alan at abaigun or find someone in canada that fixes old and new crosman airguns...
Thanks Kevin, I appreciate your help.
Hal
your welcome
I replaced the o-ring, with one of same size, but still all gas is running out fast from that release point, just before barrel. what can be the fault in my gun? I dont have access to service center in my country...
Is something else related to the release of the gas in every shot mechanism?
Thanks
Awsome video got me back up and going thanks man
thanks and congrats
I tried to contact. no answer. I replaced the o-ring you use in 5:20 of the video. Can rapid loose of gas from that position, conected to the "quads" (i suppose is those 2 on both ends of that brass pipe)? Or can it be because of the part you replace in 6:50 ?
Thanks again
I have a brand new crosman vigilante , I just has a doubt is that when i cock the hammer you know the metal that make contact with the valve to shot , well that part when i cock the hammer moves from back to front , is that normal? or need to be fixed , also everytime i use a co2 with it it just last for 40 consecutives shots, that is normal too?
yes all normal operation except the shot count is not consistant for speed from shot to shot over 40 shots how ever still normal
@@KevinMillard68 so do you think that there's a problem with the gun valve ? I used a screwdriver in that circle part around the valve to make sure it was adjusted.
Videoanleitung - SUPER! Danke.
the one iam working on in the video is the older 357 not the newer one and the indexing prawls are different , the bb version uses the older indexing prawl as does the older pellet version,
I'm sure they should have a parts rebuild kit for all cr 357 model made dates somewhere- i was looking at this flick and figured on ordering my part i need, its the leaking seal ring(s) but i guess you or i would have to contact crosman and may not like their price and keep checking-
Is Teflon oil safe to use on this gun? I bought it recently and I'm not sure how to oil it other than the oil drop that goes on the co2 cartilage
I'd like to modify mine for more power. Is there any way to do that with this particular gun? I would like to be able to take small game with it.
ok so what your saying is your valve stem seal is shot then ,
My dad is trying to assemble his Crossman 357 but the only piece missing is the wedge mentioned. I was thinking of making one myself so I was wondering if you could tell me the measurements of the wedge. Or better yet, if there is a place you can buy one. Thanks.
sorry cant help you on that one i dont have any but you can use a med powered small spring in place
Alright. thanks!
your welcome
potatosword I used a spring that fit in that spot just right. the wedge that it had was all gummed up and started to fall apart
Can I change the wedge by myself without breaking the seal you were talking if you take your Crossman 357 apart? I ordered the new wedge (the piece that helps support the latch at the barrel break) i have the brown grips which is the older model Crossman 357. Is there a video on how to do it? Thank you for your video!
Terry Fry the side cover must come off to change the support boot, you have a 1 in 10 chance that you wont toast the quad seals when you pull the cover
Nice Video! My 357 loses all gas from the front hole (before the barrel).
Where do i find a seal kit? I searched with no luck... Thank you!
The video is very instructive.
How to order a repair kit?
Tks.
call crsoman see of they have one for you for the new model guns they should as for older 357s Ebay or see if you can find a USA shop thats still fixing the old ones
great video! I have a similar Crosman Vigilante, with a broken barrel latch. is there anywhere that you know of where I could get a replacement part? thanks!
+MrAlexanduh if the place you bought it from also repairs them then goto them other wise any place the fixes crosman airguns doa google search and you can also goto abairgun.com as well for crosman parts
The 38T is a lot easier to put back together . Nice vid you made.
either one to me is easy but after you do it a few hundred times i guess anything is easy lol
On the top of the gun where it clicks together mine won't stay closed and lock in?
you need a new latch support boot
@@KevinMillard68 where can I get one
As far as I know there are no restrictions here on pellet guns. Were can I find an 8 inch barrel? Could you do a video showing how to perform said mods? I'm not trying to take anything more than small rabbits. I have a .22 and a pellet rifle that has plenty of power but I'd like to be a bit quieter and I like using a pistol for compact reasons also. Thanks for your response. By the way I eat everything I kill (except rats)
Plus we're do you buy that seal kit?
Does the steel barrel just float inside plastic housing? Mine started coming out and I had to push it back in.
more or less it floats the metal hanger is all that sort of locks the metal barrel in
KevinMillard68
Thanks, I’ll have to check into it better. The barrel actually fell out on me when I was loading it.
I have not been able to get consistent accuracy with it.
Frank L ya its not 100% accurate but its a fun gun. its limits are pretty much 10 meters for accuracy but you will get strays, you do need to find a good pellet for it tho its a picky bugger
Cause I've only had it for a week. but anyways how much do you charge to fix it?
Juan Esquivel if you have only had it for a week then you have a warranty, also i no longer fix airguns, but i do refer people to abairgun.com
Hi Kevin, I have one of the 357's but believe it may be an older one. The grips are brown plastic and the right hand one is held in place with two screws. My question to you is, do you still repair them, and if so, would you be willing to do mine?
Hal
i dont repair them anymore sorry i dont even have any parts left i got right out of pellet guns , you can get the parts from alan at abairgun.com just let him know which 357 you have and get the parts from him its really easy to fix them ,, call him after 6:30pm his time zone faster to call him them to email him
Hey kevin, im from central texas and was wondering how much it would be to send you my Crosman 357, i got it in the mail after ordering it. the weapon preformed well but i was out and about on a "Recon" when i heard a clank in my pistol...i opened the case to find that the firing rod had come out of place...nothing appears to be broken, i just not 100% sure the "Correct" way to put it together