Single Point Injection System

Поділитися
Вставка
  • Опубліковано 16 лис 2024

КОМЕНТАРІ • 34

  • @alanbayliss6401
    @alanbayliss6401 2 роки тому +6

    Commentary rather than music, even though it is nice music, would have been more useful but thanks for posting the video

  • @cellgreen2043
    @cellgreen2043 5 років тому +3

    To buy a Diaphragm of a fuel regulator , do you have a part number for this Mono Point Injector?

    • @MrIngorodrigues
      @MrIngorodrigues 4 місяці тому

      You can serach for Golf monotronic or fiat Tipo monotronic

  • @RuneJensen-o8z
    @RuneJensen-o8z Рік тому

    Hi Oliver Tube - NICE NICE Video .. do yo know where to get the o ring at 4.31 around that nossle?

  • @mattnorgrove6872
    @mattnorgrove6872 7 місяців тому

    Hi, thanks for the video! Do you know what resistance values should be seen when measuring across the injector?

    • @OliverTube
      @OliverTube  7 місяців тому

      most fuel injectors should read between 10 and 18 ohms by Google!

  • @christoph7395
    @christoph7395 2 роки тому

    Excellent video, thank you so much it is so helpful.

  • @mulusewayalew2433
    @mulusewayalew2433 3 роки тому +1

    Where can I get a brand new mono injection

  • @RichardNash100
    @RichardNash100 3 роки тому +2

    @Olivertube seem to have trouble starting when hot? or and does anyone know why? I have this system or very similar to it

    • @trickywoo356
      @trickywoo356 2 роки тому +1

      I have the same problem - did you end up fixing yours?

  • @dodogot5814
    @dodogot5814 6 років тому +2

    super video. i was planing to dismatle my monopoint. This one is from Saxo / Peugeot 106 ?

    • @OliverTube
      @OliverTube  6 років тому

      It's from Fiat Uno, but can be found in many vehicles, Renault, Volkswagen ...

    • @dodogot5814
      @dodogot5814 6 років тому +1

      @@OliverTube good to know, i have one just like this in Citroen Saxo 1.1.

  • @yunusertas
    @yunusertas Рік тому

    this system same with vw 1.8 abs engine?

  • @philtolfreeart
    @philtolfreeart 2 роки тому

    Hi there, do you know how to obtain replacement diaphragms for the fuel pressure regulator on these? This stuffs getting so rare now!

    • @christoph7395
      @christoph7395 2 роки тому

      Breakers yard or buy a donor car. Or fashion your own. Or junk the whole injector for something more modern. I've got the same problems here.

  • @ronenfe
    @ronenfe 5 років тому +1

    how do you set the tension of the throttle cable? my idle speed is too low so I put more tension on the throttle cable. I have Renault twingo 95.

    • @OliverTube
      @OliverTube  5 років тому +1

      Easy peasy, just press the throttle pedal til the end and the watch how it is moving the idle speed sensor(it should move the cable in accordance with applied throttle)... idle speed its not regulated by throttle cable, idle speed sensor does that - regulate the idle speed of the engine...

    • @ronenfe
      @ronenfe 5 років тому

      @@OliverTube So what do I do if my idle is poor and I have starting problems? I have just finished rebuilding the engine after the head gasket blew. Compression in cylinder 2 and 3 still low. But I want to compensate that by increasing idle speed

    • @ronenfe
      @ronenfe 5 років тому

      I disassembled the monopoint, actually I have Weber 2905C, not much info about it.

    • @ronenfe
      @ronenfe Рік тому

      It was the engine temperature sensor which was bad.

  • @saxophonias
    @saxophonias 3 роки тому

    how did you adjust the Throttle position sensor once you got it out? I have been facing problems with the monopoint and swapping the tps is a nightmare to adjust correctly as i have been told.

    • @OliverTube
      @OliverTube  3 роки тому

      service manual could help u with this question!

  • @ronenfe
    @ronenfe Рік тому

    You have to clean the injector by making it work with a cleaner going through

  • @fabioprates792
    @fabioprates792 6 років тому

    Why my bosch ma 3.0 does not do returning to the tank and why i have black smoke that the exaust , can u help ?!

  • @azisiskonstantinos3473
    @azisiskonstantinos3473 3 роки тому

    How much tightening on the three bolts of the membrane cup?
    How to align the potentiometer properly?

    • @ronenfe
      @ronenfe Рік тому

      I have a different model, but i just tighten the screws by feeling, it doesn't really matter. Also I didn't adjust the throttle position sensor, just installed it in place. Didn't have issues.

  • @dxxm2339
    @dxxm2339 5 років тому

    That pin in the middle of red rubber, has some movements or not?

    • @OliverTube
      @OliverTube  5 років тому

      Yes, It did! It's how it work...

  • @poweroftrolling3863
    @poweroftrolling3863 7 років тому

    What are the values of the other screw?

  • @mousmous7266
    @mousmous7266 Рік тому

    Bonjour je recherche cette pièce pour ma mini open british spi.
    Quelqu'un peut m'aider svp

  • @alanrose4827
    @alanrose4827 5 років тому

    Do not forget the dashpot!

  • @MrMultipaul
    @MrMultipaul 4 роки тому

    Spi vw animation