NX3 Evo Gyro flight controller Balance working | Gyro for Airplane
Вставка
- Опубліковано 12 лис 2020
- NX3 Evo Gyro flight controller Balance working | Gyro for Airplane
How to make rc airplane
-------
* Link buy: www.banggood.com/custlink/3mK...
--------
***Join as a member of this channel to enjoy privileges:
/ @thangengineer
* Please SUBSCRIBE my channel: bit.ly/2w1CRU0
* Don't forget Share, Like, Comment this video.
---------
* More video:
- How to make RC Airplane Pinkus at home | DIY Airplane at home: • How to make RC Airplan...
- How to make RC Plastic Bottle Aircraft at home: • How to make RC Plastic...
- How to make RC Arrow Plane | 100% fly: • How to make RC Arrow P...
- How to make a Helicopter from foam that 100% fly: • How to make a Helicopt...
- How to make RC Batwing Plane at home | 100% fly: • How to make RC Batwing...
--------
* My playlist:
- How to make: bit.ly/2nElxjX
- DIY: bit.ly/2ODWklg
- AWESOME LIFE HACKS: bit.ly/2MLWSVO
- Amazing: bit.ly/2MiXaXN
- Simlpe & fun life hacks: bit.ly/2KVezQT
* Connect with Us:
- My channel: bit.ly/2w1CRU0
- Gmail: thangtvmt79@gmail.com
Thanks for watching!
#Howtomake #NX3_Gyro #ThangEngineer - Навчання та стиль
I saw your video while ate my breakfast,there isn't nothing best👍
Thank you. Have a good breakfast to you
Nice Airplane.I like it.
Thank you 😍😍
Subscribed to your channel but I have a question please...At 4.27 why did you plug the second aileron (Aileron R) into the bind location of the iA6B? I thought that it was only a 6 PWM channel receiver. Also at 7.40 to 7.50 you plug the 2 aileron servos into Aileron and Aileron R after having set the T dip switch to the right for "Beginner Mode" at 5.20. I ask because the manual you have been kind enough to show clearly says at item 5 "Dual Aileron Settings" - "Note. Do Not use Beginner Mode with Dual Ailerons.
Please don't take this as criticism as I think your videos are quite useful for beginners and this is about the only On-line source of a diagram and manual for the NX3 Evo for which we should be very grateful. Thanks. ☺
I would think you'd need to adjust the throw of the servos so they extend more especially with how small the control surface is. It doesn't look like they move enough in both directions.
Anyway, that's a good video. Tomorrow my nx4 evo will be here. Hopefully now I'll be able to keep my airplane in the air longer than just 5 seconds
Ok bro
I am first watching
Thanks
Always glue the servos on last - and after bending the servo rods
Nice plane! Did it fly?
My plane only has rudder and elevator, no ailerons.
Will the NX3 Evo work with that kind of plane ?
Works better than it looks
This channel is so cool!
Hi in first
Hi
Please make a video for setting fixed wing with this nx3 evo
Bro can you make using solar combo battery.. can you make that
Bro I ordered new kk2.1.5 flight controller for 5000 and while programming it suddenly the text dissapeared😢 what to do now
I recommend you to make rc plane using drone circuit and cardboard.please
I make it bro
@@BANGEKOLAPAR Is it real fly?
It Fly and you can make it at home.hehehe
@@BANGEKOLAPAR Can you show me please.
@@tinsan2836 see me
I Guess Next video is Fly this Rc😁😁😁😁
Ok i wait for next
Plz give me the buy link of this flight controller
ha ha ha,.......
Hello do you think this flight controller may work directly without any receiver? thanks
Yes
सब सामान कहाँ से मिलेगा मुझे इसकी आवश्यक है
dear sir.... can you give me a copy of this instruction manual...please..
Ok. Sent message to my gmail
@@THANGEngineer hello sir...im just sent you an mail on your gmail ID...
Ok
Hello i have crossfire nano rx with 6channels pwm, how i connect nx3 evo to multi? i dont get it, its only with one wire
all my servos have 3wires not 1
Here's 3
@@THANGEngineer but i mean one wire on each, not 3 on each,
1 servo need 3 wires, 2 for electric, 1 for signal, if you have 1 wire, it can't not servo. Ok
@@dankhalifa6937 The "Multi" connection on the Nx3 EVO is NOT a normal servo type connection.(Signal/+/-) It is a Signal, Signal , Signal input. You must connect the bottom pin to the signal output of your receiver "Mode Switch" channel. The middle pin to the signal output of your receiver "Rudder" channel and the top pin to the receiver "Aileron" output. You don't need to run + and - to each receiver PWM output since the + and - rails are all connected.
Omg its my first time answering a youtber
Yes. It is really
Pagal