FINALLY! Some instructions I can follow. I have the Jumper Transmitter for a while now and have been searching UA-cam for an English-easy-set-up video. Found none from no-one...until now. Thank you so much for this.
Really helpful especially as I was struggling to find option to adjust Expo. I love this TX and will likely buy the new Plus version once I can get it in the UK!
G’day Andrew, my preference for a motor off / safety switch is not a toggle switch, that can be inadvertently bumped, but a rotary dial, that you have to turn through half way to activate. Funny how ideas change, never had expo 30 yrs ago, so used hi low rates etc low rates for normal, high rates for panic. Now I find the idea especially in the USA is, low rates for high speed, high rates for slow speed / 3D. My preference unless flying 3D, is no rates just expo, at 50 to 70. Just my thoughts. Jumper looks very much like Futaba 8sg
Hi Andrew, on the T8SG I want to activate channel 8 so I can use Aux 4 or Aux 5 (wheels), to be able to control the stabilizer gains in flight for the Lemon RX Plus stabilizer. Any idea how to setup parameters for channel 8? Also I have use Simple correct?
First, a big thank you for making this video. I have watched a fair bit of your other videos (and even copied your rescue boat but I haven't used it yet). One question I have is if it is possible to have different expo for different rates? I have a Spektrum DX9 and what I tend to do for new models till I figure out their characteristics is set up a 3 pos switch with high 100 expo 40, mid 80 expo 25 and low 60 expo 10. It makes the curve near the middle of the stick consistent in all rates and just the end of the stick is where things behave differently. Is there any way to do this on the T8SG?
@@AndrewNewton Hi Andrew, congrats for your channel! I was looking for a "cheap" tx and I felt in love with the multiprotocol thing...at first I was looking for a flysky but I use mainly gliders and it's impossible to make a full house glider with the limit of 3 mixes... Is the Deviation software more complicate than openTX? A taranis would be great but it's out of budget
Hello, THIS VIDEO IS THE CLOSEST HELP TO ACTUALLY BEING ABLE TO SET UP A JUMPER T8SG (PLUS in my case). As a beginner I still havent got a clue on how to setup a JUMPER T8SG PLUS to be able to use it to control my E-Flite Carbon Cub SS RC plane. Can someone PLEASE tell me where to go to be able to understand HOW to set it up? Like for instance all under MIXERS, you have 1-AiL, 2-ELE, 3-THR, etc. Why then on mine does it say, 1-THR, 1-AIL, 3-ELE, etc.? Or does it matter that they are in different positions, urs having Ailerons on Channel 1 and mine having Throttle on Channel 1?? Does THAT part matter? Thank you in advance!! From there I STILL have a loong way to go! But, THAT would at least help me a bit. BTW, I’ll pay someone to step me thru everything! Art
The channel order may depend on which protocol you choose or it may be in the transmitter setup menu somewhere. Can change from TAER to AETR and many other options. More setup videos here ua-cam.com/users/andyandvirgsearch?query=jumper
FINALLY! Some instructions I can follow. I have the Jumper Transmitter for a while now and have been searching UA-cam for an English-easy-set-up video. Found none from no-one...until now. Thank you so much for this.
Just want to say ,you are a life saver, I couldn't arm my KingKong Fly Egg 130 ,after watching your video, it is in the air, Thank You
Wonderful, thanks for the feedback
Really helpful especially as I was struggling to find option to adjust Expo. I love this TX and will likely buy the new Plus version once I can get it in the UK!
Andrew the best explanation and way to configure my T8SG radio.
Thanks for sharing.
Greetings from La Paz BCS Mexico.
Glad it was helpful!
Thanks Andrew - you're a champion. It is easy when you know how :-)
Ha no problem Dave, it's not that simple really, took a fair bit of trial and error. This is a quirky operating system.
Would you be able to show how to add flaps and rudder mixing for better bank turns? I appreciate the hard work you put into your channel👍🏻
Sorry Steve, I don't have this radio now
G’day Andrew, my preference for a motor off / safety switch is not a toggle switch, that can be inadvertently bumped,
but a rotary dial, that you have to turn through half way to activate.
Funny how ideas change, never had expo 30 yrs ago, so used hi low rates etc low rates for normal, high rates for panic.
Now I find the idea especially in the USA is, low rates for high speed, high rates for slow speed / 3D.
My preference unless flying 3D, is no rates just expo, at 50 to 70.
Just my thoughts.
Jumper looks very much like Futaba 8sg
I usually only have rates for the first few flights, then expo and control linkage adjustment after that.
this video helping me a lot thanks
I thought it would be more difficult, this tx isn’t really dummy friendly, but that was okay… thanks bro 😎
No problem 👍
Hi Andrew, on the T8SG I want to activate channel 8 so I can use Aux 4 or Aux 5 (wheels), to be able to control the stabilizer gains in flight for the Lemon RX Plus stabilizer. Any idea how to setup parameters for channel 8? Also I have use Simple correct?
No longer have this radio sorry.
First, a big thank you for making this video. I have watched a fair bit of your other videos (and even copied your rescue boat but I haven't used it yet). One question I have is if it is possible to have different expo for different rates? I have a Spektrum DX9 and what I tend to do for new models till I figure out their characteristics is set up a 3 pos switch with high 100 expo 40, mid 80 expo 25 and low 60 expo 10. It makes the curve near the middle of the stick consistent in all rates and just the end of the stick is where things behave differently. Is there any way to do this on the T8SG?
I like your thinking. I no longer have this radio but from memory it is possible, but complicated to program with the Devo firmware.
Think this would make a great second radio to replace my old Orange transmitter. Still love my Q7, best.
Nothing beats OpenTX, I get frustrated trying to work out these other operating systems.
Hey Andrew, thoughts on this transmitter vs the flysky? Im a newbie but keen on a good product that won't die in 2 years.
Flysky would be my choice, I dont like the Deviation firmware that the Jumper uses. But I would recommend a Taranis QX7 over everything else.
@@AndrewNewton Hi Andrew, congrats for your channel!
I was looking for a "cheap" tx and I felt in love with the multiprotocol thing...at first I was looking for a flysky but I use mainly gliders and it's impossible to make a full house glider with the limit of 3 mixes...
Is the Deviation software more complicate than openTX?
A taranis would be great but it's out of budget
hye, may i know if this tx has helicopter setup such as idle up, throttle cut, did it can be setup for 3d helicopter ?
No idea sorry. I dont have the radio anymore
Is this radio for only electric foamies or can I use this on glo and petrol based models?
Radios are not restricted in that way. Can use them for anything
@@AndrewNewton I just thought they were more orientated toward electric applications, thanks for your reply.
Hello, THIS VIDEO IS THE CLOSEST HELP TO ACTUALLY BEING ABLE TO SET UP A JUMPER T8SG (PLUS in my case). As a beginner I still havent got a clue on how to setup a JUMPER T8SG PLUS to be able to use it to control my E-Flite Carbon Cub SS RC plane. Can someone PLEASE tell me where to go to be able to understand HOW to set it up? Like for instance all under MIXERS, you have 1-AiL, 2-ELE, 3-THR, etc. Why then on mine does it say, 1-THR, 1-AIL, 3-ELE, etc.? Or does it matter that they are in different positions, urs having Ailerons on Channel 1 and mine having Throttle on Channel 1?? Does THAT part matter? Thank you in advance!! From there I STILL have a loong way to go! But, THAT would at least help me a bit. BTW, I’ll pay someone to step me thru everything! Art
The channel order may depend on which protocol you choose or it may be in the transmitter setup menu somewhere. Can change from TAER to AETR and many other options. More setup videos here ua-cam.com/users/andyandvirgsearch?query=jumper
Thank you so much
Hey Andrew how to setup expo rate on mix elevon?
I think you'd set it up the same way. Right??
thanks a lot !!
Anyone know how to add flaperons on the jumper t8sg?
Anyone?
my friend can you make file we can copy into tx easy if you could
No longer have this radio
@@AndrewNewton thank you
What that means expo 30 high rate.
Rates and Expo change how much effect you get from moving the sticks. Do a search for Rates and Expo, plenty of better explanations out there.
Andrew Newton Ok. Thanks I appreciate it.