How To Make AC 2 In 1 Meter | utsource | Arduino Project
Вставка
- Опубліковано 1 жов 2024
- Hi friends in this video I have made an Arduino based AC Volt Ampère Meter this is a useful project Please like share and subscribe
Buy Electronic components
www.utsource.n..."
IC chip: www.utsource.net
IGBT: www.utsource.n...
electronic component: www.utsource.net
Capacitor: www.utsource.n...
diode: www.utsource.n...
Find chips: www.utsource.net
Transistors: utsource.net/c...
Darlington: www.utsource.n...
Sensors: www.utsource.n..."
Circuit diagram: drive.google.c...
Arduino Code : drive.google.c...
Components:
1x ARDUINO NANO
1x 16X2 LCD
X LM358 IC
1X 100A CT
1X 47 OHM RESISTOR
1X 2.2K RESISTOR
1X 4.7K RESISTOR
3X 10K RESISTOR
6X 470K RESISTOR
1x 10K TRIMPOT
1x 2 Pin Terminal Block
1X PERF BOARD
JUMPER WIRES
My Channels:
KIYANI' KI LAB / @kiyanikilab
KIYANI TECH / @kiyanitech
Instagram: / kiyani676
fecebook: / kiyanis-lab-1520512291...
#electronicsproject #arduinoproject #acmeter
Good Idea.
But I wouldn't spend ₹250 on Arduino nano, ₹150 on 16x2 display, ₹80 on I²C module when I can get all of these in a ₹150 multimeter.
It's only important for specific projects and learning electronics but isn't that important for daily requirements.
yes you are right you can use cheap microcontroller for the purpose
The main purpose of this channel is to learn some things, not to spend or save money.
@@deterdamel7380 exactly. This project is good for learning electronics. But if we compare the cost then there are a lot of cheap modules which do the same job. If we can upgrade it to an LCR meter then it will be worth it.
نحتاج منك ats جينج أوفر أربع خطوط لتحويل التيار بين الخط العمومي والمولدات ومع تايمر وشاشات صعود نزول للتايمر مع جرس نغمة بيزو لكل خط خاص به وتعديل الخصائص للحماية الخاصة من التيار الكهربائي العالي الواطى مع الزمن
yes bro similar project is in the list
What is the name of the program you use to draw the circuit, and thank you?
Good video sir ❤
Great work,
What about the meter for 4 in one in your short video
There is a big variation in the voltage
No Calibre
CT Ratio ????
jump to 1:40
Hi nice project but i don t understans what i must connect to L and N connector..........thx a lot for answer
one wire of the load will go through ct and line neutral of meter should be connected to line neutral of the supply
good morning, I'm still Piero from Italy, thanks again for the first reply, but tell me if I understood correctly.
I connect the 220 volts to the L-N sockets. Still on N, I connect one of the two cables of the hoat gun, and I pass the free cable of the hoat gun inside the coil, then I connect it to L.
Practically the 220Vac is read from the input of the OP AMP and, at the same time, when load which is affected by the passage of current measured by the coil........I hope my interpretation of your words is correct... ..I don't want to explode the ARDUINO NANO and all the out board.....BEST REGARDS Piero
Good job friend. This is nice one. What is the function of 47ohms in the circuit
it is the burden resistor
@@KiyanisLab can you explain the more the function of the burden resistor pls
A burden resistor is typically used in electrical circuits, especially in current measurement applications. It converts the current flowing through a circuit into a voltage drop across the resistor. This voltage can then be measured and analyzed by other components in the circuit. In essence, the burden resistor "burdens" the circuit with a known resistance, allowing for accurate current measurements.
@@hearttouchingstoriesofreallife Correct indeed!
Always amazing
Very good
Good
SÜPER DEVAM