This is exactly what I am doing to my truck! a small repair on my F150 hood and rest of paint is good condition,, so this shows exactly what I want to do,,, thank you so much sir,, for sharing your extreme talent to the public,,,,,, you are a very talented person,,,,,,, wow 😳👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼 perfection....,, 🙏🏼🙏🏼👌👍🏼
I have seen so many u'r video, but after looking this one, I just got little smiles.. Because we use the same gun, Devilbiss GTI Pro-Lite, and then Belanova paint 50:50, 35bar air press, 50% overlapping, n for the Clear Coat, I'm using Spies Hecker 8040 75:25, 28bar air press, 25% overlapping With this "marshall" gun, everything's so easy to take.. Devilbiss GTI Pro Lite!!!
Good job guess, I could not tell what you were spraying, blend chemical or clear, the only time I knew was when you sprayed the base, then not sure. What pressure? I guess I'm in the wrong level?
@@Luca-lx7ol The blender actually does nothing to blend the color, its just a wet transparant coat you put on, so that paint that lands outside the spot you are aiming at doesnt " sit " on top of the panel. If it does, the paint becomes like fine dry sand, and when you clear coat over it, it looks gritty. Also, like he says, you should stay away from edges when aplying blender. You add more color depth by adding layers, which can make some colors look darker. Its the same for clear coating with some colors, especially if the original manufacter paint has very thin coats, and you paint heavy by comparison. The color doesnt actually change, but your eyes perceive it as such. Its like looking into a pool. The shallow end will appear to have a lighter blue bottom, while the deep end will look dark blue. It's ofcourse all the same when you remove the water.
@@Seneric Thanks for the explanation, when i asked the question i was using Ppg envirobase, now i'm using Standox Standoblue and i can confirm it! Yes I know about that thickness of layer change the color or also metamerism 👍 👍👍 Good job
Superb finish!!well done! which of the products is the blend that you use in the pro lite before the base and which is the code of that? also if it needs to mix it! thank you!
he shows there, he hits full on the spot and then blends thru the outsides, he makes this steps updown and then from side to side, at the end the hood has the original color on each side/edge whic is color match for the rest of the car paint, he just blends the spot that he paints against the original pain on the hood. He does this from 4:10 forward with the base and then just clearcoat fhe whole hood
Blender.... Its basically a clear basecoat.. You spray a closed wet coat of it so that the metalics from your basecoat melt into it - instead of landing on top in little unseen dimples & irregularities in the prepped factory paint....
@@thistledewoutdoors3331 thank you sir, does basic clear coat mean only clear without using hardener or special material? because I have heard certain brands specifically for blanders, because they are not available in my country / city.
Not the way I would have done it , I was starting to cringe with vertical pass one side and horizontal the other. I guess it comes down to what works best for you.
There are lot of mistakes ypu have done like after completing one side ..you started spraying clear from the midle of the hood 11:04 ... another mistake...you don't care that clear is sprayed on the edges properly or not...you just cover the edges at last which may result in orange peel on the edges
Donde yo trabajo se le llama bulldog pero en general creo que es como una capa transparente que ayuda a que la pintura se pegue mas y ayude a eliminar Los rayones
Hola...cualquiera sea la marca o linea del producto, este esta diseñado para aplicarse a una capa mediana humeda,solamente sobre la superficie matizada original sin primario. Su proposito, es de tener una superficie humeda al momento de aplicar la mano del color,para que las perlas metalicas se acomoden o nivelen. Asi asegurar una buena nivelación o difuminado del color sobre la superficie sin saturar mucho el color. Aqui el técnico, a mi parecer a utilizado pintura a base de agua, razón por la que a cubierto el primario rapidamente. La tecnica de su aplicación es según el fabricante...en este caso, una mano humeda y posteriormente una mediana, para uniformar textura y difuminar color. Su aplicación es de una mano mediana humeda
This is exactly what I am doing to my truck! a small repair on my F150 hood and rest of paint is good condition,, so this shows exactly what I want to do,,, thank you so much sir,, for sharing your extreme talent to the public,,,,,, you are a very talented person,,,,,,, wow 😳👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼 perfection....,, 🙏🏼🙏🏼👌👍🏼
It doesn't get any better than that, you make it look so easy. Thank you for sharing your techniques.
¡ BEAUTIFUL WORK ! Y NO SE LE CHORREA NADA EL CLEAR A PESAR QUE NO LE DA PAUSA DE UNOS MINUTOS DE LA PRIMERA MANO....FANTASTIC.
Why you didn't let clear flash between coats?
Bardzo dobra praca bravo ...pozdrawiam z Polski
Excellent works
very good job adhesion promoter for intermediate layers and vanish with color makes and finally transparent and ready
Nice work! But it seems alot clearcoat for a hood. How much did you used? Congrats from Portugal
I have seen so many u'r video, but after looking this one, I just got little smiles..
Because we use the same gun, Devilbiss GTI Pro-Lite,
and then Belanova paint 50:50, 35bar air press, 50% overlapping,
n for the Clear Coat, I'm using Spies Hecker 8040 75:25, 28bar air press, 25% overlapping
With this "marshall" gun, everything's so easy to take.. Devilbiss GTI Pro Lite!!!
Would you ever do any videos on color matching any metallic color light or dark?
Very nice spray painting 👍👍
Beautiful finish
It looks absolutely insane. Congrats.
Good to hear😁
Good job guess, I could not tell what you were spraying, blend chemical or clear, the only time I knew was when you sprayed the base, then not sure.
What pressure?
I guess I'm in the wrong level?
That is just beautiful. Great job Edwin.
Thanks!!
Which aircap / needle size do you use?
Great job my friend 👍👍👍
6
Your work is veary buotiful
Perfect job thanks man
عالیه،یک سوال داشتم،اون چی بود قبل رنگ زدی ،
Mr channel,,why are you not using the (gold) prolite for base coat or clear coat.!!?
complimenti good finish
i love all your jobs
Thanks Ail Ail love to hear that✌
Impressive blend !
Very nice! If you spray the paint without the coat of blender, the paint will be mottled ?
Not necessarily, but blending in the middle of a hood isnt always the easiest. The blending agent just makes the final outcome a little easier.
Ty !
@@Luca-lx7ol The blender actually does nothing to blend the color, its just a wet transparant coat you put on, so that paint that lands outside the spot you are aiming at doesnt " sit " on top of the panel. If it does, the paint becomes like fine dry sand, and when you clear coat over it, it looks gritty.
Also, like he says, you should stay away from edges when aplying blender.
You add more color depth by adding layers, which can make some colors look darker.
Its the same for clear coating with some colors, especially if the original manufacter paint has very thin coats, and you paint heavy by comparison.
The color doesnt actually change, but your eyes perceive it as such.
Its like looking into a pool. The shallow end will appear to have a lighter blue bottom, while the deep end will look dark blue.
It's ofcourse all the same when you remove the water.
@@Seneric Thanks for the explanation, when i asked the question i was using Ppg envirobase, now i'm using Standox Standoblue and i can confirm it! Yes I know about that thickness of layer change the color or also metamerism 👍 👍👍 Good job
That's good paint
Nice job 👍
Hi, what's the benefit doing it Vertically instead of Horizontally for blending the basecoat?
you sprayed it with some kind of blend in thinners at the start?
He said "1050"
Nicely done
Thanks!
Ziet er mooi uit man.
Superb finish!!well done! which of the products is the blend that you use in the pro lite before the base and which is the code of that? also if it needs to mix it! thank you!
The blender is 1050
Also can use straight out of the tin,I tend to add 20 percent 6050 or 6052
Ele aplca , o verniz primeiro ? Depois fas o retoque com a tinta ? Depois que vem com verniz final?🤔
Lo primero que aplica es bending
Nice paint from Philippines
Do you need to mate the element before applying it with a blender ??
nicely done !
ماهي الماده التي تم اطلاءها قبل الصبغ الدهان أنا صباغ شاحنات كبيره وشكرا
EXCELLENT TRAVAIL
Please tell me what is your first spray for blend before spray base coat.
Good
What is covered before you paint
Van you tell me, step by step?
Cant see n blend, great job. I wish we didnt have to cut everything in and hang it. That stand looks sweet
What's the name of the blender ?
Very good 😣
Great vid, thx!
Thanks!
bad sanding, clear will peel off from those shiny spots when rock hit them
special!!!!!!!
Indeed! nice to do so.
y el ahorro de material no importal? con 600ml le doy una mano por abajo a todo un coche
Nice one there
Gangster shit!!
Supper
É impressão minha ou ele não deitou endurecedor no verniz ?...
Nice job! What’s blender you used ?
looks like WB2091 from axalta
I think it's wb1051
👏👏👏
How much filler was hinding under the paint?
Muito bom seu trabalho
a question please :
What is the method of matching the paint with the rest of the car parts?
he shows there, he hits full on the spot and then blends thru the outsides, he makes this steps updown and then from side to side, at the end the hood has the original color on each side/edge whic is color match for the rest of the car paint, he just blends the spot that he paints against the original pain on the hood. He does this from 4:10 forward with the base and then just clearcoat fhe whole hood
I just painted the hood. The color you sprayed is not like the rest of the original car parts What's the solution? ?
I just painted the hood. The color you sprayed is not like the rest of the original car parts What's the solution? ?
Keep rubbing that hood!
I’m done with clear by now ….keep rubbing
Bon trveille
Number 1 !!!!
👍👍!
what was sprayed before the paint layer?
Blender.... Its basically a clear basecoat.. You spray a closed wet coat of it so that the metalics from your basecoat melt into it - instead of landing on top in little unseen dimples & irregularities in the prepped factory paint....
@@thistledewoutdoors3331
thank you sir, does basic clear coat mean only clear without using hardener or special material? because I have heard certain brands specifically for blanders, because they are not available in my country / city.
What clear are u using ?
Very well
What Cain of material you used on your firts code
Not the way I would have done it , I was starting to cringe with vertical pass one side and horizontal the other. I guess it comes down to what works best for you.
Hey man his color match is there. No need to hate on somebody if you don't enjoy their content just don't watch mate
josss
Why not flash off time
Buenos pintado
Muito bom.
Eldaro Reis sim
Perfeito!! Não precisa polir
How long before you apply the second coat and clearcoat
About 8-10 minutes or it depends if you paint in a camera heat room
Essa pintura é poliéster ? Ou Pu
The clear coat gun is was size tip
What gun devlbiss
Devilbiss gti pro t110 cap 1.2mm nozzle
Terbaik. Good job. Bro.
πρεπει να βαριεσαι που ζεις τι πινεις ρε φιλαρακι
Great finish
I’m pretty sure that’s waterborne paint...?
Yes it is👍
Gooddd
Awsome work..
What brand this gun for blowing
muito bom dutch parabens
There are lot of mistakes ypu have done like after completing one side ..you started spraying clear from the midle of the hood 11:04 ... another mistake...you don't care that clear is sprayed on the edges properly or not...you just cover the edges at last which may result in orange peel on the edges
I am paniter in the Ford company India punjab
What did u spray 1st?
Wetbed?
It was blender base without pigment like clearcoat
عالی
Siapa orang Indonesia like😊
Consumption ??
Teach me please🙏
WOW
Como ASE uno para comunicarse
Nice job!
aeso le llamo arte es una bellesa la difuminado que al 100
Needs better preparation!
Ficou top
👏👍✊
You basically painted it edge to edge so how is that a blend
Im like
Como se llama el producto que aplico primero saludos
Donde yo trabajo se le llama bulldog pero en general creo que es como una capa transparente que ayuda a que la pintura se pegue mas y ayude a eliminar Los rayones
O puede solamente ser un blend una capa de pintura ligera para que see vea del mismo color
Chromax Blender, así se llama el producto, no es Bulldog, el bulldog es un promotor de adhesión
Hola...cualquiera sea la marca o linea del producto, este esta diseñado para aplicarse a una capa mediana humeda,solamente sobre la superficie matizada original sin primario. Su proposito, es de tener una superficie humeda al momento de aplicar la mano del color,para que las perlas metalicas se acomoden o nivelen. Asi asegurar una buena nivelación o difuminado del color sobre la superficie sin saturar mucho el color.
Aqui el técnico, a mi parecer a utilizado pintura a base de agua, razón por la que a cubierto el primario rapidamente. La tecnica de su aplicación es según el fabricante...en este caso, una mano humeda y posteriormente una mediana, para uniformar textura y difuminar color.
Su aplicación es de una mano mediana humeda
nice, bro 👌
Do you ever use cheep guns
hi bro