Sir 1. B was behind VP, hence it could have been either in II or in III quadrant. Then why did we assume it so? 2. 45° angle was made wrt XY line. So for other generalised cases, we must draw an angle of 90-theta right (with a as vertex)?
Hi Sruthi.... Thanks for appreciating my work.... Do spread a word about this channel with your friends, classmates and juniors so that all can benefit.
hllo sir i have a doubt why we are using only smal letters instead capital letters as because in ur question the projectors in caps then y are u using small letters pls reply
Hi Arif.... I am sure that these videos are helping u learn... Keep watching and do let your friends know about this channel so that they can also benefit.......
Arishma Kashyap All the very best Arishma...... i hope that you have benifited from my lectures...... And after writing tomorrow's exam do tell me how it went...... All the very best again......
Note. You fullfill every engineers request and make life easy... Thanks sir
Sir
1. B was behind VP, hence it could have been either in II or in III quadrant. Then why did we assume it so?
2. 45° angle was made wrt XY line. So for other generalised cases, we must draw an angle of 90-theta right (with a as vertex)?
sir i want to understand same peoblem
problem
Bhai konse college ka hai tu?
Arey Rey arey rey
thank u sir i have my xam by tomorrow i have listened all ur viedoes now i have understood well.....thanking u alot sir
Hi Sruthi....
Thanks for appreciating my work....
Do spread a word about this channel with your friends, classmates and juniors so that all can benefit.
+Manas Patnaik for sure sir I will definitely do .....
I have problem in this topic but you solve my problem.. Thanx
Sir how did you consider point B in sec quadrant sir ?
Sir, I too have the same doubt.
Thank you so much for explain me.my dought is clean thanks boss...
Very helpful classes
Hi Tiger.........
I am sure my videos are helping you learn.....
Keep watching and do share this with your friends also...
All the best......
Sir I thought I was going to fail Ed but now I'm gonna top them thnx to you 😊
Sir why ur taking 30mm below the xy line
Thank u sir for giving very simply solutions
All the best.....
Subjectwise Playlist:
1. Engineering Drawing/Graphics (English): ua-cam.com/video/WG6H2pISUzQ/v-deo.html
2. Engineering Drawing/Graphics (Hindi): ua-cam.com/video/SB83cUaAiCM/v-deo.html
3. Engineering Mechanics / Applied Mechanics: ua-cam.com/video/Z4WN2Z9okfs/v-deo.html
4. Mechanics of Solids / Strength of Materials / Mechanics of Materials: ua-cam.com/video/Co4YlavCpeQ/v-deo.html
5. Theory of Machines: ua-cam.com/video/Co4YlavCpeQ/v-deo.html
6. Machine Drawing: ua-cam.com/video/iFCnFUR9Gdc/v-deo.html
7. Engineering Drawing for Engineering Services Prelims: ua-cam.com/play/PLIhUrsYr8yHwFTNav_k3EEIvztQEQHilU.html
8. Physics for Class 11: ua-cam.com/video/0fejUC79LZY/v-deo.html
9. Manas Speaks Series: ua-cam.com/play/PLIhUrsYr8yHz9g5V7Lw_BA5UXbAbgVyf0.html
10. Channel 2 Link:
ua-cam.com/channels/_aqx41HWeOebfL6FqBYU6Q.html
Thanks sir
Gud explanation sir but I m getting only 40mm distance between b and b'
Watch that problem from this playlist:
Projection of Points: ua-cam.com/play/PLIhUrsYr8yHxEk_Jv8yOatn3Dcr6KYK3j.html
Sir is there any another model for this problem?
hllo sir i have a doubt why we are using only smal letters instead capital letters as because in ur question the projectors in caps then y are u using small letters pls reply
That is just a thumbrule....
sir thanks a lot for making these videos
+Tanshu Arora
Always there to help u guys.....
Tanshu do check out all the content on my channel page in topicwise's playlists.....
Have fun.....
Thank you brother!
very very thanks sir
Thanks you sir...👏
Thanks buddy 💖😊
good explation thanks
Hi Arif....
I am sure that these videos are helping u learn...
Keep watching and do let your friends know about this channel so that they can also benefit.......
it's so urgent Sir
❤❤
This is not objective approch oriented... You should solve it with mathematics too...
i got bb' as 47 mm
Arishma Kashyap
its ok....Arishma......2mm human error......
not to worry....
i am sure u have learned the core idea behind this problem....
Manas Patnaik yes sir thanku very much .. tomorrow i hav my graphics exm .. o hav learnt ds concpt
Arishma Kashyap
All the very best Arishma......
i hope that you have benifited from my lectures......
And after writing tomorrow's exam do tell me how it went......
All the very best again......
sir how to to decide it first or third quadrant
Sir plx upload the videos of md plxxx plxxx plxxx
plxx
Thank you very much sir
1. Engineering Drawing (English) :
ua-cam.com/play/PLIhUrsYr8yHwDUrVYmUNYkEeZgZTvoIfS.html
2. Engineering Drawing (Hindi) :
ua-cam.com/play/PLIhUrsYr8yHx0C3ebAW-FQxTP8ig8-QxU.html
3. Engineering Mechanics:
ua-cam.com/play/PLIhUrsYr8yHxfOmcGIeUThHEr9lQ3IXRS.html
4. Mechanics of Solids:
ua-cam.com/play/PLIhUrsYr8yHzft7ygw5THZo4aDcsxEadP.html
5. Theory of Machines:
ua-cam.com/play/PLIhUrsYr8yHx0aFXSQvT7nm6ivJSMKnAU.html
6. Machine Drawing:
ua-cam.com/play/PLIhUrsYr8yHzwT06rv7u3tqdfmmKOCz1w.html
7. Engineering Services Examination_Engineering Drawing_Prelims:
ua-cam.com/play/PLIhUrsYr8yHwFTNav_k3EEIvztQEQHilU.html
8. Physics for Class 11:
ua-cam.com/play/PLknJ2c9H1euEwtFJLUGZvkjG35OoVvemM.html
9. Manas Speaks Series:
ua-cam.com/play/PLIhUrsYr8yHz9g5V7Lw_BA5UXbAbgVyf0.html
10. Physics Channel Link:
ua-cam.com/channels/_aqx41HWeOebfL6FqBYU6Q.html
very very thanks sir