Wow, Very Good Job. Your attention to detail is spot on! I am engineer of over 50 yrs experience and to me you got this nailed. I always try and do same with my CS restorations.
I love the video this only goes to show you if more people would take care ove their stuff they would not have to go out and buy more you did a sweet job mark
Excellent rebuild as usual, I failed to restore my Mcculloch pro mac 46 II few years ago couple mistakes ended up in broken magnetic flywheel. It is always refreshing to see someone competent doing it right..
Excellent work and video! I especially liked how you re-tied the pull start handle rope exactly like the original, even if any knot would have worked! Great attention to detail and pride in your work.
Great restoration mate, impressive skills including video editing. You didn't grease the main bearing (at least not on camera and started assembling it dry) and also the reason you were cutting curves in the test piece is uneven sharpening of the chain teeth (or possibly the chain too loose / sitting too high on the bar because of dressing the bar edge shallows the groove). Thanks for sharing!
Absolutely beautiful work on the restoration side of things. Yes if its nut & bolt restoration, you may by pass those parts depending on their condition, but the only mention I'll make is what about inside the fuel and oil tank?!
Although I usually love videos where you turn cord tools into cordless tools, I really enjoyed this one because it shows us how to properly dismantle a chainsaw, what is not always obvious ( because of counterclock screws and many other things ). And like usually, the great work you do into cutting the rushes and making videos without times off, is remarkable, your videos are so clean and relaxing to watch. Thank you for all that and keep doing what you are a master in, really ! :)
In Argentina they bring an identical machine, probably a Chinese replica of this chainsaw with the name of Nakama 52. This video is excellent for repair!
Nice work, very satisfying to watch you bring it back to service and look good also. I wish you can show the weight of the saw and how many cc’s the engine is and maybe even length of the bar. Looks like Ryobi took cues from the top saw brands to make theirs. Looks very well built and I’m happy to see the detailed video angles.
Very enjoyable video. I'm restoring an MS200T for myself and the fins have hard, baked on crud. Ryobi did a great job of keeping the engine and fins clean. Stihl did not. Brake cleaner and powerful burnt soldering flux solvents won't touch it. Oven cleaner will probably need multiple applications and heating of the upper to work. I'm cautious with caustic chemicals on the aluminum cylinder.
да это мля его пила по ходу, в говне измажут а потом на умняках разбирают и чистят, ни сальники , ни подшипники не проверил, карбюратор тоже толком не разобрал не проверил иглу и сеточку, и не настроил, шланги тоже на целостность не проверил, поршень неправильно тоже стоит к выхлопу! так чисто для просмотров видео делают! Ремонт и реставрация 2 разные вещи тут по ходу)
I enjoyed the video, the restoration was well done and satisfying to watch. The chain could have been sharpened a bit more evenly and maybe tightened a bit more to cut well. Over all; a masterful job! Keep it up!
Nice work! One little advice: never use torque on the spark plug. If you overtorque it, then you can strip the thread. Just simple thread it in with hand and fasten it a little with a plug wrench.
Great job on resurrecting this saw. Ryobi makes an awesome machine; I traded a Mcculloch Pro Mac 850 and another Pro Mac 700 for a mint Ryobi. My saws needed fuel lines and i think carb diaphragms. My saws had so much compression, they were hard to pull over. I think the guy I traded with didn't know what he had. I had another Mac 10-10S that he wanted, but I was able to do the trade with just the two non-runners.
Your video are very instructive! from a learning point of view, it would be nice to add some comments about the produts and the tools you use for the cleaning and the restauration.
No oil was applied to bearings, seals, piston and cylinder. First "dry" start will wear cylinder surface. Stupid mistake and all job going directly to the trash bin. Grats! Keep it going!
■ ▪︎EVANGELIO DE SALVACIÓN ■ ▪︎ CONDENACIÓN Apocalipsis 21: ⁸ Pero los cobardes e incrédulos, los abominables y homicidas, los fornicarios y hechiceros, los idólatras y todos los mentirosos tendrán su parte en el lago que arde con fuego y azufre, que es la muerte segunda. ■ ▪︎PLAN DE SALVACIÓN Romanos 5 ⁸ Mas Dios muestra su amor para con nosotros, en que siendo aún pecadores, Cristo murió por nosotros. ⁹ Pues mucho más, estando ya justificados en su sangre por Él seremos salvos de la ira. Juan 3 ¹⁶ Porque de tal manera amó Dios al mundo, que ha dado a su hijo unigénito, para que todo aquel que en Él cree, no se pierda, mas tenga vida eterna. Romanos 10 ⁹ Si confiesas con tu boca que Jesús es el Señor, y crees en tu corazón que Dios lo levantó de los muertos, serás salvo. ¹⁰ Porque con el corazón se cree para justicia, pero con la boca se confiesa para salvación. ■ ▪︎PROMESAS DE SALVACIÓN 1 Tesalonicenses 4 ¹⁶ Porque el Señor mismo con voz de mando, con voz de arcángel, y con trompeta de Dios, decendera del cielo; y los muertos en Cristo resucitarán primero. ¹⁷ Luego nosotros los que vivimos, los que hayamos quedado, seremos arrebatados juntamente con ellos en las nubes para recibir al Señor en el aire. Y así estaremos siempre con el Señor Apocalipsis 21 ³ Yo oí una gran voz del cielo que decia: He aquí el tabernáculo de Dios con los hombres, y Él morará con ellos; y ellos serán su pueblo, y Dios mismo estará con ellos como su Dios. ⁴ Enjuagará toda lágrima de sus ojos de ellos; y ya no habrá muerte, ni habrá más llanto, ni clamor ni dolor; porque las primeras cosas pasaron. ■ ▪︎CONFESIÓN DE CRISTO COMO SEÑOR Y SALVADOR Señor hoy reconozco que el pecado que hay en mi vida me separó de ti, yo me arrepiento sinceramente y te pido que entres a mi vida, yo confieso con mi boca y creo en mi corazón que tu moriste por mí en la cruz, hoy te recivo en mi corazón como mi único y suficiente Salvador, gracias porque apartir de este momento soy tu hijo y mis pecados han sido perdonados, en el nombre de Jesús amén.
Do you only like videos like this? I would like to know if you like my videos. In one of my latest projects, I made a sapphire ring from a titanium tube.
I know next to nothing about this kind of activity, so , I admire your skills. Do you have any bits left over after you put it back together again? 🤷♂️😀
Nice video. I would change the fuel pump button (cup), you glou it together, but it will fail soon in my opinion. Hope you greas or oil at least the bearing at 16:54.
I could not have done it better. Why did you not take apart the carb and make sure all jets were blown out and tune it too? Why not file down the depth gauges (rakers) when you sharpened? You probably would have got much bigger chips instead of sawdust coming out and cut faster too. Try to replace the ring, bearings, etc if possible. Maybe not enough time but You don't want to have to do all this work twice. Just my two cents but you are talented and do excellent work. It looks brand new!!! Video your tear down is a great idea. Thank you!!!
Поршневое кольцо - старое, все прокладки - старые. Люфт подшипников коленвала не проверяли. Праймер зачем-то на клей посадили (а по итогу еще и потёк 27:07). Игольчатый подшипник не заменили (28:28). Ведущая звезда старая, с износом (14:02, 28:33). Шину не проверяли на износ, покрасили и поставили обратно. Цилиндр при сборке протянули неправильно (18:18). Это не реставрацией нельзя назвать. Это просто пустая трата времени. Рабочую пилу помыли, а что нужно заменить из запчастей - не заменили.👎
А что вы хотели от цыганского художественного фильма? Всё блестит значит кино удалось.Медленное раскладывание деталей на столе это не то что проверить цпг на герметичность.Про откручивание сцепления это вообще шедеврально , и почему потом лопается колленвал. Главное один покажет а другие потом повторяют. Я всегда ищу в видео технические нюансы а здесь потраченное время смыто в унитаз! Автору что бензопилу красить что кастрюлю , разницы нет.
esta realizando un mantenimiento preventivo esa es la idea luego si falla algo se remplaza la idea es un mantenimiento sin gastar igual cada persona lo hace como quiere
I'm a very worthless person. This chainsaw has no value. It cost less than $200 brand new. It's not appropriate to restore and use the scraps, but I'm doing it to make money from the videos. I've made a lot of money from it.
This chainsaw is fairly new, maybe from around 2014, also You can see that there is barely any wear on the parts. The title of the video should be “complete disassembly / reassembly”. Restoration is when You restoring something very old and usually damaged / heavily used to perfect condition.
Я когда свою пилу после ремонта забрал так легко не мог дёрнуть за шнурок , приходилось ногой наступать на ручку и потом только мог потянуть шнурок и это не по причине плохого ремонта . а по причине хорошей компрессии в поршневой . а здесь слишком легко дёргает за шнурок .
Is identical with parkside pkbs 53a1 probably the same chainsaw different brands! But it has some tricks to become monster, just a few holes to exhaust and boom brand new faster chainsaw than before!☺️
Impressive work, when you have an open engine it is convenient to change gaskets even if they seem to be fine, as a detail I would have liked a little yellow paint to revive the chainsaw even more
another fantastic job pay attention to the Riker and that's the tooth in between each cutter for a straight edge across if the raker is higher than the cutter tooth you will be forcing a sharp blade through every time makes it difficult for The Cutting to to actually cut file the tops of the rakers down
Wow, Very Good Job. Your attention to detail is spot on! I am engineer of over 50 yrs experience and to me you got this nailed. I always try and do same with my CS restorations.
وا
really like the design of this saw. a rebuilder's dream. still can not get over how good of a condition the piston and cylinder were in
С 38 кубиков кубиков бензопилы китайской подходит
This guy restored EVERYTHING...
incredible!!!!!!
Doesn’t need restoration. Chainsaw supposed to look like that…
this guy resteres nothing
I love the video this only goes to show you if more people would take care ove their stuff they would not have to go out and buy more you did a sweet job mark
ua-cam.com/video/qjIrsZ_U7PA/v-deo.html
Excellent rebuild as usual, I failed to restore my Mcculloch pro mac 46 II few years ago couple mistakes ended up in broken magnetic flywheel. It is always refreshing to see someone competent doing it right..
Ex
And the way the parts, nuts, bolts laid out etc... magnificent. It just makes it all sooooo much easier
I didn't make a mistake with this method.
Excellent work and video! I especially liked how you re-tied the pull start handle rope exactly like the original, even if any knot would have worked! Great attention to detail and pride in your work.
安恩pop
@@陳金塗-n9k л
ua-cam.com/video/qjIrsZ_U7PA/v-deo.html
Great restoration mate, impressive skills including video editing. You didn't grease the main bearing (at least not on camera and started assembling it dry) and also the reason you were cutting curves in the test piece is uneven sharpening of the chain teeth (or possibly the chain too loose / sitting too high on the bar because of dressing the bar edge shallows the groove). Thanks for sharing!
Absolutely beautiful work on the restoration side of things. Yes if its nut & bolt restoration, you may by pass those parts depending on their condition, but the only mention I'll make is what about inside the fuel and oil tank?!
Okay, thank you for the feedback.
Although I usually love videos where you turn cord tools into cordless tools, I really enjoyed this one because it shows us how to properly dismantle a chainsaw, what is not always obvious ( because of counterclock screws and many other things ). And like usually, the great work you do into cutting the rushes and making videos without times off, is remarkable, your videos are so clean and relaxing to watch. Thank you for all that and keep doing what you are a master in, really ! :)
I'm so glad you like my work, thank you for sharing!
Жа
ลขย
جهه ز
جج٠
In Argentina they bring an identical machine, probably a Chinese replica of this chainsaw with the name of Nakama 52. This video is excellent for repair!
Nice work, very satisfying to watch you bring it back to service and look good also. I wish you can show the weight of the saw and how many cc’s the engine is and maybe even length of the bar. Looks like Ryobi took cues from the top saw brands to make theirs. Looks very well built and I’m happy to see the detailed video angles.
Great suggestion! Thank you so much!
@@gear_showpå åå😊😊😊😊😊❤
That chainsaw has some guts. I never heard any of them accelerate like this one does. Almost puts Stihl to shame!!!
The video is x2 speed
BRAVO! There he is! Mr. Gear Show! Well done! Thank you!
You're welcome, thank you!
Very enjoyable video. I'm restoring an MS200T for myself and the fins have hard, baked on crud. Ryobi did a great job of keeping the engine and fins clean. Stihl did not. Brake cleaner and powerful burnt soldering flux solvents won't touch it. Oven cleaner will probably need multiple applications and heating of the upper to work. I'm cautious with caustic chemicals on the aluminum cylinder.
vinegar
Необычно легко всё разобралось, удивился даже.
да это мля его пила по ходу, в говне измажут а потом на умняках разбирают и чистят, ни сальники , ни подшипники не проверил, карбюратор тоже толком не разобрал не проверил иглу и сеточку, и не настроил, шланги тоже на целостность не проверил, поршень неправильно тоже стоит к выхлопу! так чисто для просмотров видео делают! Ремонт и реставрация 2 разные вещи тут по ходу)
З таким інтелектом краще промовчати.@@___yanichar___1107
That poor chainsaw was the definition of " Rode hard and put up wet ". Good job on the restoration.
Crankcase was spotless compared to the outside of it!!
ဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈဈ
၏၏၏၏၏၏၏၏၏၏၏၏ဈ၏၏၏၏၏၏၏၏၏၏၏၏၏၏၏၏၏၏၏၏၏၏၏၏၏၏၏၏၏၏၏စစ၏၏၏၏၏၏၏၏၏၏
Sounds like my wife.
Uducciicdiicccíxucuuccw0cixiixixifícicciicdicixxxuxsxxuxuxxixxuuxuuyzzjzuhshuysysysysysdyysp😊😅😅@@iamaduckquack
Nice video My friend. Very old engine
Thank you very much! My friend.
I enjoyed the video, the restoration was well done and satisfying to watch. The chain could have been sharpened a bit more evenly and maybe tightened a bit more to cut well. Over all; a masterful job! Keep it up!
I'm glad you like this video, thank you!
😅😅😅
A fascinating journey of restoring a 2-stroke engine chainsaw, the Ryobi ESK 3500.
Nice work! One little advice: never use torque on the spark plug. If you overtorque it, then you can strip the thread. Just simple thread it in with hand and fasten it a little with a plug wrench.
Exactly, he should have used a manual wrench. And should have oiled the air filter - without it, it does not work properly.
yea that was so cringe. I wonder if any of the bolts were hand checked.
ยจะได้
ه
😂
Your telling me that little engine powers that chainsaw 😮
wonderful I cheered when you cut the wood
great job bro japan quality restoration
Thank you!
Pretty amazing job brother!!! Beyond talented and expert skills. Thank u
Thanks for watching
Great job on resurrecting this saw. Ryobi makes an awesome machine; I traded a Mcculloch Pro Mac 850 and another Pro Mac 700 for a mint Ryobi. My saws needed fuel lines and i think carb diaphragms. My saws had so much compression, they were hard to pull over. I think the guy I traded with didn't know what he had. I had another Mac 10-10S that he wanted, but I was able to do the trade with just the two non-runners.
เ
Them old Mccullochs are starting to get collectible because the old company, hell even their yellow paintjob is long gone
My god 2 stroke ?
You are legend Bro ( Gasoline,eletric,batery)
Amazing Bro fan from Brazil!
I'm still learning too :) anyway, thank you so much!
🙏
Man upload vídeo Rotary Hammer makita HR 2470. 127v to batery.
Please 2470 my favorite Hammer.
Quá tuyệt vời luôn, rõ ràng và cẩn thận đến từng chi tiết nhỏ nhặt nhất, mong ad sẽ ra nhiều video thật hay cà hữu ích hơn nữa. 👍👍👍👍👍
ua-cam.com/video/qjIrsZ_U7PA/v-deo.html
Chainsaw is my favorite power tool!
Well done you are a genius, great work
Your video are very instructive! from a learning point of view, it would be nice to add some comments about the produts and the tools you use for the cleaning and the restauration.
No oil was applied to bearings, seals, piston and cylinder. First "dry" start will wear cylinder surface. Stupid mistake and all job going directly to the trash bin. Grats! Keep it going!
Deine Arbeit ist so erstaunlich!!! Ich freue mich immer auf ein neues Video! Du bist echt Spitze!!!👍👍👍🤗🤗🤗
Vielen Dank, freut mich sehr, dass dir mein Video gefällt.
Broke it down barney style
Love it thanks for saving her
ryobi's design of this saw provides for easy disassembly
Yes, it is.
Pięknie, wygląda jak nowa👍
ua-cam.com/video/qjIrsZ_U7PA/v-deo.html
■ ▪︎EVANGELIO DE SALVACIÓN
■ ▪︎ CONDENACIÓN
Apocalipsis 21:
⁸ Pero los cobardes e incrédulos, los abominables y homicidas, los fornicarios y hechiceros, los idólatras y todos los mentirosos tendrán su parte en el lago que arde con fuego y azufre, que es la muerte segunda.
■ ▪︎PLAN DE SALVACIÓN
Romanos 5
⁸ Mas Dios muestra su amor para con nosotros, en que siendo aún pecadores, Cristo murió por nosotros. ⁹ Pues mucho más, estando ya justificados en su sangre por Él seremos salvos de la ira.
Juan 3
¹⁶ Porque de tal manera amó Dios al mundo, que ha dado a su hijo unigénito, para que todo aquel que en Él cree, no se pierda, mas tenga vida eterna.
Romanos 10
⁹ Si confiesas con tu boca que Jesús es el Señor, y crees en tu corazón que Dios lo levantó de los muertos, serás salvo.
¹⁰ Porque con el corazón se cree para justicia, pero con la boca se confiesa para salvación.
■ ▪︎PROMESAS DE SALVACIÓN
1 Tesalonicenses 4
¹⁶ Porque el Señor mismo con voz de mando, con voz de arcángel, y con trompeta de Dios, decendera del cielo; y los muertos en Cristo resucitarán primero.
¹⁷ Luego nosotros los que vivimos, los que hayamos quedado, seremos arrebatados juntamente con ellos en las nubes para recibir al Señor en el aire. Y así estaremos siempre con el Señor
Apocalipsis 21
³ Yo oí una gran voz del cielo que decia: He aquí el tabernáculo de Dios con los hombres, y Él morará con ellos; y ellos serán su pueblo, y Dios mismo estará con ellos como su Dios.
⁴ Enjuagará toda lágrima de sus ojos de ellos; y ya no habrá muerte, ni habrá más llanto, ni clamor ni dolor; porque las primeras cosas pasaron.
■ ▪︎CONFESIÓN DE CRISTO COMO SEÑOR Y SALVADOR
Señor hoy reconozco que el pecado que hay en mi vida me separó de ti, yo me arrepiento sinceramente y te pido que entres a mi vida, yo confieso con mi boca y creo en mi corazón que tu moriste por mí en la cruz, hoy te recivo en mi corazón como mi único y suficiente Salvador, gracias porque apartir de este momento soy tu hijo y mis pecados han sido perdonados, en el nombre de Jesús amén.
nice job👍👍
Thanks
You are a very good repairman I enjoyed your channel good luck
Do you only like videos like this? I would like to know if you like my videos. In one of my latest projects, I made a sapphire ring from a titanium tube.
相当な熟練者。キャブレターの分解・組付けと巻き戻しバネの組付けが見たいです。
zenoah castings some of the best ive seen
I love how you left a bit of wear and tear on it
Very well done sir👏 I watch it till the end❤💚💜💛
Great job, thank you brother. You are so talented
You're welcome, thank you!
The inside of the engine was mint.
Finally welcome back Mr gear show , It's been 11 days since i dont see your new video❤️❤️
I'm so glad that you still enjoy my video, thank you!
Ovakvi majstori su veoma, veoma retki. Skoro da ih i nema... kod nas ?!?
I know next to nothing about this kind of activity, so , I admire your skills. Do you have any bits left over after you put it back together again? 🤷♂️😀
Good Job as usual :-) you are quite good at fixing much stuff
Thanks again!
Great work…one of your best in my opinion! Thank you 😊
Wow, thank you!
Always pleasure to watch your videos..👍🌟,never bored of this kind of restorations..💡✌️...
I'm so motivated that you like this video, thank you so much!
Bravo sir, Bravo. A total and complete refurbishing of that chain saw and it not only runs well, but looks good too... Thumbs Up!
Thank you for sharing! I'm glad you like it.
Excelente trabajo, amigo, quedo 100% operativa!
te agradezco
Nice video. I would change the fuel pump button (cup), you glou it together, but it will fail soon in my opinion. Hope you greas or oil at least the bearing at 16:54.
Well done sir. I truly aspire to have this level of knowledge, patience and attention to detail.
My Güde KS400B looks quite similar. Thanks. Your Vid will help me
I could not have done it better. Why did you not take apart the carb and make sure all jets were blown out and tune it too? Why not file down the depth gauges (rakers) when you sharpened? You probably would have got much bigger chips instead of sawdust coming out and cut faster too. Try to replace the ring, bearings, etc if possible. Maybe not enough time but You don't want to have to do all this work twice. Just my two cents but you are talented and do excellent work. It looks brand new!!! Video your tear down is a great idea. Thank you!!!
Поршневое кольцо - старое, все прокладки - старые. Люфт подшипников коленвала не проверяли. Праймер зачем-то на клей посадили (а по итогу еще и потёк 27:07). Игольчатый подшипник не заменили (28:28). Ведущая звезда старая, с износом (14:02, 28:33). Шину не проверяли на износ, покрасили и поставили обратно. Цилиндр при сборке протянули неправильно (18:18).
Это не реставрацией нельзя назвать. Это просто пустая трата времени. Рабочую пилу помыли, а что нужно заменить из запчастей - не заменили.👎
Я промотал быстренько до момента "посадки подшипников" Поржал, поставил дизлайк и закрыл, только бы это г... Не появлялось в рекомендованных снова!
ARATĂI TU LA OM CUM TREBUIE FĂCUT CĂ TEORETIC VĂD CA DAI DIN GURĂ DAR SĂ VĂD UN VIDEO CU O RESTAURARE FĂCUTĂ DE TINE NU AI👎👎👎👎
А что вы хотели от цыганского художественного фильма? Всё блестит значит кино удалось.Медленное раскладывание деталей на столе это не то что проверить цпг на герметичность.Про откручивание сцепления это вообще шедеврально , и почему потом лопается колленвал. Главное один покажет а другие потом повторяют. Я всегда ищу в видео технические нюансы а здесь потраченное время смыто в унитаз! Автору что бензопилу красить что кастрюлю , разницы нет.
esta realizando un mantenimiento preventivo esa es la idea luego si falla algo se remplaza la idea es un mantenimiento sin gastar igual cada persona lo hace como quiere
I'm a very worthless person.
This chainsaw has no value. It cost less than $200 brand new. It's not appropriate to restore and use the scraps, but I'm doing it to make money from the videos.
I've made a lot of money from it.
Excellent restored sir good work thanks for sharing.
Bạn là người đàn ông tuyệt vời, một người thợ có tay nghề rất giỏi, công việc này tôi rất thích, cảm ơn video của bạn.
Bạn được chào đón, tôi rất vui vì bạn thích công việc của tôi. Cảm ơn bạn!
@@gear_show cho tôi hỏi là bạn là người việt nam hay người nước nào vậy?
This chainsaw is fairly new, maybe from around 2014, also You can see that there is barely any wear on the parts. The title of the video should be “complete disassembly / reassembly”.
Restoration is when You restoring something very old and usually damaged / heavily used to perfect condition.
Amazing and detailing job my friend congratulations 👏👏👏
Thank you so much 😀
Каждый день этим занимаюсь на работе, только качественней!
Я когда свою пилу после ремонта забрал так легко не мог дёрнуть за шнурок , приходилось ногой наступать на ручку и потом только мог потянуть шнурок и это не по причине плохого ремонта . а по причине хорошей компрессии в поршневой . а здесь слишком легко дёргает за шнурок .
Та невже, напевно всі болти на фіксатор різьби, щоб потім не розібрати.
Is identical with parkside pkbs 53a1 probably the same chainsaw different brands! But it has some tricks to become monster, just a few holes to exhaust and boom brand new faster chainsaw than before!☺️
That Guy is beyond being a pro his a master
Awsome work.
Really nice restoration!
Looks like cleaning all those parts was a nightmare.
Thanks for sharing, keep it comming & take care!
I'm so glad to hear that, thank you!
You done a grand job on that chain saw 😁😁👍👍
Oh really, thank you so much!
I have the newer model of this chain saw and it is fantastic. Ryobi is definitely an unrated brand.
Impressive work, when you have an open engine it is convenient to change gaskets even if they seem to be fine, as a detail I would have liked a little yellow paint to revive the chainsaw even more
Thank you for the feedback!
Nice job mate, I'm going to use your Video to help me service/restore my Saw....... Hopefully 👍👍👍👍👍👍👍
Good luck! I'm glad it helps you.
Svaka čast majstore👍
looks like new saw great job
damn that was great, excellent video, keep on cutting anything you want, thanks again for a great video... from MICHIGAN
Restauração perfeita, não a necessidade de pintar tudo e parecer artificial, para mim esse é melhor tipo de restauração possível
У меня есть старая бензопила штиль надо её тоже отреставрировать . Отличная работа ставлю большой лайк
Good job 👍👍👍Thank you for sharing. 🇨🇦
You're welcome, thank you!
Bravo,ottimo lavoro soprattutto molto ben pulito
another fantastic job pay attention to the Riker and that's the tooth in between each cutter for a straight edge across if the raker is higher than the cutter tooth you will be forcing a sharp blade through every time makes it difficult for The Cutting to to actually cut file the tops of the rakers down
Usted es un trabajador milagroso. 👍🏻🙇🏻♂️
¡Muchas gracias!
Good job 👉💛☝️✅
Thanks ✌
Motorsägen mechatroniker meister...😊
nice video, very professional
Thank you!
It looks great well done
You are talented..! 👏👏👏
Thank you!
po myciu zagubił się z tłoka kołek ustalajacy położenie pierścienia, no i składanie silnika na sucho bez kropli oleju... Ale ogólnie niezła robota
It's nice to see a restoration that's an actual restoration and not something nice destroyed to make it look like junk.
Me encanta ver tus manos haciendo magia
I have Chinese copy of this exact saw so I'm saving this vid for future reference
Excellent Job well Done
Thank you so much!
Why do you switched from ultrasonic bath to this vibrator? Is it really better cleaning parts?
Back when Ryobi used to make top tools.
They also sold a 2C drill and reciprocating saw.
Great video thanks for sharing 🙏🙏
I hope the next user take better care of the saw than the last user...its was the worst i have seen...
Good wotk enyway..💪👍👍
I'm always wondering usage of gasoline/vibration to metal parts. But since parts becomes very clean you can't argue with the results.
Xin hỏi ad, để tẩy rửa rỉ sét , nhớt bám trên vỏ mà lâu ngày khó cọ rửa được, thì sài dung dịch tẩy rửa nào là hợp lý và tiện dụng nhất ?
Amazing! How old is this chainsaw? How many years did it not used before? Looks like it`s not too old, but it really used in very bad conditions...
That was just so amazing.
Superb Job Well Done
Great cleanup and restore
Thank you!
I'm surprised he didn't replace the bearing while it was in parts -crazy!!
doomguy: "a fine addition to my collection."
I'm glad you like it.