Loose the tool bag and speedo ,air filter tie your clutch and throttle cables together. Loose your left arm outa the wind see how many rpm you pick up. Aerodynamics is holding you up. Best China 🇨🇳 motor on 🌎 today.
@@Op1zilla I got the G5 steel iron sleeve cylinder and I left Kevin a text message and a voice message asking him for your phone number when I get it I'll call you and you can tell me your address brother to me the cylinder looks clean and good just got the usual steel over hang in all the ports thick steel lining it came with piston rings no wrest pin bearing lower gasket and head gasket intake and exhaust gasket and nuts and bolts for exhaust and intake it will all be in the box I'm sending you
Sounds awesome except for that serious miss on the high end lol. Building a bike that can go 55 for a couple minutes at a time is pointless. That engine won't hold together barely longer than what you showed in this video before it grenades! So the point was?
nice build, mine tops out around 30, bone stock zeda 80 with 44t, on a walmart bike i got out of a dumpster lol. i don't even want to go faster than 30 lol, well maybe a little bit faster :P might go down to 40t to make 30mph a little more comfortable.
Living through you again... I've got the Samger 49mm steel sleeve motors with bird on one side of the cylinder... Not sure if it's the same G5 from about 2-3 years ago... There's a 47mm steel sleeve for a Grubee super rat i got from Grubee 10 years ago that's for 39.5 long rod... The super rat was a flop because of the mag/coil was one piece and would over heat... takes 40x17 bearings for the crank and different seals... Lot of different possibilities... There's a saw ignition that fits it.. Boy Goes fast stil has a few G motor bottom ends, coils seals if anyone searches sellers other items on his EBay
All I want to do is angle the transfers so they don't shoot the charge at the top of the piston... And up to the head... And the usual clean up... Some JB weld to port match the cylinder to the sleeve and not the sleeve to the cylinder... Garden hose cleaning it up helps direct the flow.... Or a case full of water bolted down without a head... 💦
@@jasonburque I think the fuel is designed to wash the top of the piston, that's how it keeps it cool an not seize up, but thats also why I make a small boost port most times an angle it dead center of head, its been working great 👽👍🏻
I live in natchez im trying to build a bmx cub i have the bmx frame just need the welding done that would allow for the motor to be mounted glad i found your channel
Good Luck with The Cub, They are Cool but you gotta keep your pedals or the ice will give you flack, Get a person who can weld good an not some moron, 👽👍🏻
Have you done any engine work to your motor porting the intake and exhaust I see you have an upgraded cylinder head that thing goes faster than my stock avenger engine on my fault faker bike I believe I hit 40 mph
And that's why these bicycle builds get old. You can't just cruise around having fun the motor is always screaming and vibrating While the weakest link is Always going to break. Wish I rather just invested my money in a used Honda GROM Instead of trying to constantly Maintain and upgrade the hundred dollar China doll. These are fun to play around with but as far as Solid reliable transportation this is not the solution. It's a fun hobby trying but trying to get from point A to point B on them sucks Compared to even a Cheap Chinese scooter. Just my opinion after building two of these.
This bike hasn't been touched in over 1 half years, I had to tighten some spokes,wheels havent came off, I changed the cylinder out after 20hours an sent it to a friend who is gonna run it, Now is bottom end has 30++ hours of runtime on it, This is a hobby like flying a Drone or fishing, This bike runs smooth an I can ride it how ever I want, PlUS its ported for Power, good down low an up TOP, I have a Truck for solid reliable transportation so get a vehicle, don't sit here an tell me your problems about why stuff doesn't work for you, sorry but your long Rant had nothing to do with this video, Cheers 👽👍🏻
Jesus Christ son that thing rockin
It has been a Great Running Setup, Very FUN Bike 👽👍🏻
Looking clean and sounding good nice pull bro, damn she’s quick !! 😎👍🏽
Thanks, Its fun to just ride around too, dont always go Fast 👽👍🏻
Most people need a Minarelli hybrid to get those speeds( or a KTM50sx 😊) All hail the new king in town 👑!!!
🌲🌴😊👽👍🏻🌴🌲
Loose the tool bag and speedo ,air filter tie your clutch and throttle cables together. Loose your left arm outa the wind see how many rpm you pick up. Aerodynamics is holding you up. Best China 🇨🇳 motor on 🌎 today.
Thanks for advice Dave, The bike was loaded to ravel around so loosing all tools an air pump and hud will definitely Help 👽👍🏻
@@Op1zilla love the cheap China stuff. YOU MADE IT RUN THAT FAST WITH YOUR HANDS. Great job.
Hell yeah brother nice run
Thanks bra, went 1 mph faster on a hit going home 👽👍🏻
I would officially crap myself!!!
Sweet sweet looking ride
🏆🏆🏆
☮️🦘
Pt, it will make you think twice about your choices lol, Thanks for watching, looking forward to your Travels on your 3rd Tour 👽👍🏻
Cheers my "motorised" biking brother, 🤗
🏆🏆🏆
☮️🦘
She's was getting it sounds awesome point on great job brother
Thanks Mike, 👽👍🏻
@@Op1zilla you said the other day what magic that magic brother lol
@@Op1zilla I got the G5 steel iron sleeve cylinder and I left Kevin a text message and a voice message asking him for your phone number when I get it I'll call you and you can tell me your address brother to me the cylinder looks clean and good just got the usual steel over hang in all the ports thick steel lining it came with piston rings no wrest pin bearing lower gasket and head gasket intake and exhaust gasket and nuts and bolts for exhaust and intake it will all be in the box I'm sending you
@@Op1zillaI called Kevin he told me he was going to text you my phone number earlier today give me a call brother
Sounds awesome except for that serious miss on the high end lol. Building a bike that can go 55 for a couple minutes at a time is pointless. That engine won't hold together barely longer than what you showed in this video before it grenades! So the point was?
Man I enjoy you videos hope to see you on the road. I will riding very soon.
IF you live In Louisiana along the River you Mite 🛸✨💨💨💨
nice build, mine tops out around 30, bone stock zeda 80 with 44t, on a walmart bike i got out of a dumpster lol. i don't even want to go faster than 30 lol, well maybe a little bit faster :P might go down to 40t to make 30mph a little more comfortable.
A better carb is best investment, an not a knock off, Send your money wisely 👽👍🏻
You got nice line up of bikes 🚲💨👍🏾💯
Thanks JRay, I love them all an want another but no room 👽👍🏻
@@Op1zilla i still haven’t put my new stuff on my bike yet 🤦🏾♂️and everyone riding 💯
Living through you again... I've got the Samger 49mm steel sleeve motors with bird on one side of the cylinder... Not sure if it's the same G5 from about 2-3 years ago... There's a 47mm steel sleeve for a Grubee super rat i got from Grubee 10 years ago that's for 39.5 long rod... The super rat was a flop because of the mag/coil was one piece and would over heat... takes 40x17 bearings for the crank and different seals... Lot of different possibilities... There's a saw ignition that fits it.. Boy Goes fast stil has a few G motor bottom ends, coils seals if anyone searches sellers other items on his EBay
That's where I purchased this G5 Iron 47mm, BGF, Its a favorite of mine an good price 👽👍🏻
All I want to do is angle the transfers so they don't shoot the charge at the top of the piston... And up to the head... And the usual clean up... Some JB weld to port match the cylinder to the sleeve and not the sleeve to the cylinder... Garden hose cleaning it up helps direct the flow.... Or a case full of water bolted down without a head... 💦
@@jasonburque I think the fuel is designed to wash the top of the piston, that's how it keeps it cool an not seize up, but thats also why I make a small boost port most times an angle it dead center of head, its been working great 👽👍🏻
thanks for the ride, She rips
not sure if it's just me but,The audio was a bit low , had everything cranked and could barely hear you, FYI
it was me at 1/4 volume for chrome , fixed it
If your talking about when I was riding, It was a long shot , but didnt count on people hearing me doing a lil trash Talk 😁👽👍🏻
It be stroking.... nice.... I was wondering what gear and then you said it I could never that to high nice job.👍
Yessir when you get up to those speeds you better have went over everything many times,, You just need a Jockey 😁👽👍🏻
You are a beast. Thanks for the ride
Thanks Leonard, let's get it 👽👍
Running good
Thanks DnS, had to check your channel other day make sure I haven't missed anything 👽👍🏻 Ride Safe
Is the smaller screen a rev counter? If so, how high is she screaming?
9250 in video, on ride home made another hit 9360, with 32 sprocket on rear 👽👍🏻
Nice wicked one of these days I'll hit 55 my bicycle 25
Come on Now 👽👍🏻 You Fast, you need smaller Jockey 🚴♂💥☁☁☁
I live in natchez im trying to build a bmx cub i have the bmx frame just need the welding done that would allow for the motor to be mounted glad i found your channel
Good Luck with The Cub, They are Cool but you gotta keep your pedals or the ice will give you flack, Get a person who can weld good an not some moron, 👽👍🏻
@@Op1zilla thanks for the advice
❤
❤👽👍🏻
what did u use to connect the carburetor?
CDH OZ Reed intake 23mm od for vm18 👽👍
This bike is hella fast! My bike only does 40 mph but I have no pedal chain just all motor on a 4 stroke build
That's still a nice fun Speed 👽👍🏻
what bike frame is that?
El Cheapo' China Steel Cranbrook from 2021 Covid, 👽👍🏻
Have you done any engine work to your motor porting the intake and exhaust I see you have an upgraded cylinder head that thing goes faster than my stock avenger engine on my fault faker bike I believe I hit 40 mph
Yes port work an honed the cylinder, vm18 Mikuni , Jog pipe, head has betterr combustion chamber 👽👍🏻
And that's why these bicycle builds get old. You can't just cruise around having fun the motor is always screaming and vibrating While the weakest link is Always going to break. Wish I rather just invested my money in a used Honda GROM Instead of trying to constantly Maintain and upgrade the hundred dollar China doll. These are fun to play around with but as far as Solid reliable transportation this is not the solution. It's a fun hobby trying but trying to get from point A to point B on them sucks Compared to even a Cheap Chinese scooter. Just my opinion after building two of these.
This bike hasn't been touched in over 1 half years, I had to tighten some spokes,wheels havent came off, I changed the cylinder out after 20hours an sent it to a friend who is gonna run it, Now is bottom end has 30++ hours of runtime on it, This is a hobby like flying a Drone or fishing, This bike runs smooth an I can ride it how ever I want, PlUS its ported for Power, good down low an up TOP, I have a Truck for solid reliable transportation so get a vehicle, don't sit here an tell me your problems about why stuff doesn't work for you, sorry but your long Rant had nothing to do with this video, Cheers 👽👍🏻
@@Op1zillaThis is a clean build. Nice job
recording 60fps got me screaming
Also you can't Fake the Funk either, Let's see an hear what you have Built , Im waiting lol 👀👽