Це відео не доступне.
Перепрошуємо.
How to Remove Front Bumper 97-05 Lexus GS300
Вставка
- Опубліковано 9 тра 2019
- Shop for New Auto Parts at 1AAuto.com 1aau.to/c/59/G/bumpers-and-parts
In the video, 1A Auto shows how to remove and replace a scratched, dented, broken or loose front bumper cover. The video is applicable to the 97, 98, 99, 00, 01, 02, 03, 04, 05, Lexus GS300
🔧 List of tools used:
• 10mm Socket 1aau.to/oVj/1AXAA00017
• Plastic Fastener Remover 1aau.to/oaE/1AXAA00290
• Ratchet 1aau.to/oair/1AXAA00016
• Socket Extensions 1aau.to/o4c/1AXAA00015
For More Info visit us at 1aau.to/h/bBn/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto
√ *Do it Yourself*
√ *Save Money*
DO NOT FOLLOW THEIR DIRECTIONS. As others have stated, there are two bolts on each side that they neglected to mention. They hold the bumper in on the seam directly above the turn signal. They are difficult to get to and require a 10mm deep socket. Had they taken the time to Google a diagram they would have found the same info, but instead they advised to just yank until it comes off. Following that advice I broke my bumper off below the headlight. Due to their laziness I now have to spend hundreds on a new bumper. As others have said, please pull this video.
How crucial would you say is it to put those 2 bolts back on each side of the bumper… they are a pain. Would be a lot easier to not put them back on and off in the future..
You are correct sir! I have three of these cars and there are a few bolts that need to be taken out from the back side from each side.
You forgot the 2 ten milimeter a the jonction of the bumper and the front fender, you juste broke the bumper by the way
Thanks for the help. I did see the other two on the front of each fender, no biggie if you have a foot extension and a universal with a deep socket 10mm on it. Both mine sheared off on each side but I have no intention of reinstalling so I’m good. Thanks again
Would it be similar on RX300
You were struggling because there are two bolts either side where you are pulling which hold the bumper to the wing, very difficult to reach, that's why one side came off easy because the last person couldn't be bothered to refit them.
Thanks for watching our video! +Golo1949
He's right. After my bumper wouldn't come off, I scrolled down to the comments to see what was wrong. You should pull this video.
so how many bolts are there, i counted 6?
How crucial would you say is it to put those 2 bolts back on each side of the bumper… they are a pain. Would be a lot easier to not put them back on and off in the future..
You forgot the last impossible bolt on driver side under headlight to release bumper. Other than that good video 👍
+Eric Roark Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Previous owner went to take off the bumper cover and snapped the very same clip you had problems taking off, now i’m stuck here trying to jb weld it on the inside 😂
It’s being replaced soon so i’m not really worried, but it gets annoying having to see it like that everyday
There are two more 10mm nuts if I'm correct that connects the bumper to the fender as everyone has stated already. please don't pull it will come out with ease once every nut is free. 👍
Rear bumper?
Missed like 5 more bolts but it's alright alot of times parts that been taken off before and not put back are hard to catch either that or you just ripped the rest off lol
He skipped steps.
There is a bolt on that left corner.
U said put somewhere so it don’t get scratched up u put it on the ground and yanked the other side 😂 but thanks for the help
You missed the step there are four nuts that need to come off two on each end before you can take off the bumper cover
+David Hilton Thanks for the tip! We'll pass this info along to our production team.
Yall are so annoying for this, yall should delete this video because I guarantee tons of people have followed this and fucked up their bumpers because of you , should have read the comments