You've never seen Young Man Build a Truck Without a Leaf Spring || without any Doubt Amazing Process
Вставка
- Опубліковано 31 жов 2024
- #withoutanyDoubt #TruckWithoutaLeafSpring #amazing
You've never seen Young Man Build a Truck Without a Leaf Spring || without any Doubt Amazing Process
#amazing
#TruckWithoutaLeafSpring
#withoutanyDoubt
#massproduction
Welcome to Pakistan, where you can do whatever you want with your truck.
no Brasil tudo é proibido ...leis muito rígidas
The leaf springs are there to provide flex under heavy load and to stop your bones being rattled out of your body. The ride will be so bad when the back is loaded up you'll want to go back to the original springs!
you can go back to original springs only if your truck's frame stay intact. without springs a lot of parts of the chassis will fail under stress and fatigue
Yo creo que.
1. Deberían usar mejores elementos de protección personal: guantes botas, careta para soldar, delantal de cuero y mascarilla.
2. Deberían usar soldadura más fuerte, tipo 7018, 9018, 11018.
3. Deben hacer biseles para soldar y dejar espacio entre las piezas para que se peguen o adhieran correctamente las piezas. Y más cuando sólo se puede soldar por un lado.
4. Para trabajos muy serios cómo estos es necesario aplicar la soldadura de forma vertical ascendente.
5. Para trabajos tan serios cómo estos es necesario aplicar intercalados los cordones de soldadura: a la una, a las seis 🕕 a las nueve 🕘, a las tres 🕒... A las dos 🕑, a las siete 🕖....
6. Para trabajos cómo estos es necesario precalentar un poco el área dónde se va soldar (60 grados celsius)
7. No hace falta doblar los electrodos.
8. Para trabajos tan delicados cómo estos es mejor aplica la soldadura en movimientos de letra (C) o en círculos.
9. Toda la pieza debería llevar alguna especie de temple para que no se doble tan fácil.
10. You can create a template or pattern to make the bevels with oxycut
Depends on where they're going and how fast. Huge agricultural tractors have zero suspension not even the air in the tires as they're usually filled with a liquid to give additional weight for traction. Yea if the ground is uneven and you're going at any speed they will beat the hell out of you. But smooth ground they're ok.
I think that.
1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask.
2. They should use stronger solder, type 7018, 9018, 11018.
3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side.
4. For very serious jobs like these, it is necessary to apply the welding vertically upwards.
5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖....
6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius)
7. There is no need to bend the electrodes.
8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles.
9. The entire piece should have some kind of tempering so that it does not bend so easily.
10. You can create a template or pattern to make the bevels with oxycut jjj
With all the steel they used to make that solid suspension they could of just cut some new leafs fir the spring pack to replace the broken ones ...
It's a walking beam, and it's common in heavy trucks. Add some brackets and rubber cushions (circles of rubber, cut from old tires) to the truck frame to stop the beam over rotating, and you'll have a simple, very heavy duty rear suspension.
Yo creo que.
1. Deberían usar mejores elementos de protección personal: guantes botas, careta para soldar, delantal de cuero y mascarilla.
2. Deberían usar soldadura más fuerte, tipo 7018, 9018, 11018.
3. Deben hacer biseles para soldar y dejar espacio entre las piezas para que se peguen o adhieran correctamente las piezas. Y más cuando sólo se puede soldar por un lado.
4. Para trabajos muy serios cómo estos es necesario aplicar la soldadura de forma vertical ascendente.
5. Para trabajos tan serios cómo estos es necesario aplicar intercalados los cordones de soldadura: a la una, a las seis 🕕 a las nueve 🕘, a las tres 🕒... A las dos 🕑, a las siete 🕖....
6. Para trabajos cómo estos es necesario precalentar un poco el área dónde se va soldar (60 grados celsius)
7. No hace falta doblar los electrodos.
8. Para trabajos tan delicados cómo estos es mejor aplica la soldadura en movimientos de letra (C) o en círculos.
9. Toda la pieza debería llevar alguna especie de temple para que no se doble tan fácil.
10. You can create a template or pattern to make the bevels with oxycut
@@RobertoParra-k8y Bienvenido a Pakistan!!, donde puedes hacer lo que quieras y como quieras con tu camión.
Like an old tank
LOL, the truck is standing in the dirt and the old guy is using a level to see if the wheel is true vertical
Maybe if they stopped overloading their truck they wouldn’t have to weld up a solid suspension. Not that this is gonna help, just gonna make it even more dangerous.
Begitu lah Lazim nya yg terjadi di Negara berkembang, Truk di isi dg Muatan di Luar Standar Pabrikan
So funny you said that but how true like I would say just get a bigger truck
@@Paul-iu1omгрузовик больше ждет та же судьба, его будут перегружать еще больше и следующее видео будет о том как убирают рессоры уже на большом грузовике😂😂😂
Now the frame will break instead of the leafsprings.
Yo creo que.
1. Deberían usar mejores elementos de protección personal: guantes botas, careta para soldar, delantal de cuero y mascarilla.
2. Deberían usar soldadura más fuerte, tipo 7018, 9018, 11018.
3. Deben hacer biseles para soldar y dejar espacio entre las piezas para que se peguen o adhieran correctamente las piezas. Y más cuando sólo se puede soldar por un lado.
4. Para trabajos muy serios cómo estos es necesario aplicar la soldadura de forma vertical ascendente.
5. Para trabajos tan serios cómo estos es necesario aplicar intercalados los cordones de soldadura: a la una, a las seis 🕕 a las nueve 🕘, a las tres 🕒... A las dos 🕑, a las siete 🕖....
6. Para trabajos cómo estos es necesario precalentar un poco el área dónde se va soldar (60 grados celsius)
7. No hace falta doblar los electrodos.
8. Para trabajos tan delicados cómo estos es mejor aplica la soldadura en movimientos de letra (C) o en círculos.
9. Toda la pieza debería llevar alguna especie de temple para que no se doble tan fácil.
10. You can create a template or pattern to make the bevels with oxycut
It's called a walking beam suspension a lot of trucks have this type in the US
Every place in the world you can find trucks with that kind of beam suspension, nothing new or special on it.
Yup
See them on the road, they have some kind of slanted rubber cushions
With big rubber mounts, normally 4 or six per side.
I'm not saying that you're wrong but I haven't seen one yet and I've been working around them for 24 plus years
I like how the end was painting over the dirt - a good metaphor!
Следующий этап усилить позвоночник водителя 😂😂😂😂
Hhhhhh😂
Ты рессоры их видел, толщина такая что она не работала практически.
@@griggs310 чем больше рессора, тем больше груз под которым она работает. Логично?
@@nonconformist3039
Не логично, когда пакет как у пакистанцев то это тупо становится балкой, усилие идёт на ось балансира и далее на раму, после чего видим ролики грузовиков на боку и "тапочки" варят балансиры и усиливают рамы.
Я 15 лет в дальнобое проходил, и все эти перегрузы зло.
Хозяева "тапок" убивают их на производстве, а в ютубе куча лайков какие крутые тапки))))))).
Тфу, сидят в говне по уши и лыбы дарят, типа всё ништяк ))))
@@griggs310 лайки ставят не за то что круто, а за то что прикольно - делают глупости но данная дичь развлекает.
Ремонт наверно у них дешёвый, поэтому перегружают. Типа экономически обосновано.
Such highly skilled men.............. a pleasure to watch.
Could you imagine what these guys could do with an arc Droid or even just a plasma cutter
Any poor old boy can achieve great things, when hungry...
I fear for there safety. Just look around there shop. Footwear clothing, no concrete floor etc.
звезду смерти? 🤣
если серьёзно - это бестолковая поделка
I very much appreciate that the video isn't sped up like on other channels, it brings a better perspective of the work being done. Thank you 👍
I appreciate that!
I think that.
1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask.
2. They should use stronger solder, type 7018, 9018, 11018.
3. They must make bevels for welding and leave space between the pieces so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side.
4. For very serious jobs like these, it is necessary to apply the welding vertically upwards.
5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖....
6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius)
7. There is no need to bend the electrodes.
8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles.
9. The entire piece should have some kind of tempering so that it does not bend so easily.
10. You can create a template or pattern to make the bevels with oxycut
They should just stop overloading the trucks. They will make all this solid suspension then the chassis rails will start breaking
Only 15 minutes in and I already seen continuous weld, proper use of welding shield and even caliper… think those might be foreign spies after Pakistani technology secrets 🤣
Did you happen to see and weld prep? I didn't
The reason those left springs keep breaking is because the truck is heavily overloaded.
هذا هوا العمل المتقن ممتاز جداً جداً يابش مهندس 💯💯👍🏻
I wouldn't want to have to drive that truck but I got to admit I was pretty impressive😊
Me neither
Hard work young man 😮 amazing video
Thank you 🙌
Жёстко однако, ни рессор, ни стремянок, ещё мосты усилить конкретно и просто железные колёса и будет тачка огонь, хоть по 200 тонн грузи на каждую ось. Земля главное чтоб держала.
🤣🤣🤣🤣🤣
I think that.
1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask.
2. They should use stronger solder, type 7018, 9018, 11018.
3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side.
4. For very serious jobs like these, it is necessary to apply the welding vertically upwards.
5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖....
6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius)
7. There is no need to bend the electrodes.
8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles.
9. The entire piece should have some kind of tempering so that it does not bend so easily.
10. You can create a template or pattern to make the bevels with oxycut
user-dr7zn2fi9w включи мозг. На железные колёса можно наварить протектор любой длинны и ширины. И будет грести как танк.
Excellent work !
Thanks a lot!
I think that.
1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask.
2. They should use stronger solder, type 7018, 9018, 11018.
3. They must make bevels for welding and leave space between the pieces so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side.
4. For very serious jobs like these, it is necessary to apply the welding vertically upwards.
5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖....
6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius)
7. There is no need to bend the electrodes.
8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles.
9. The entire piece should have some kind of tempering so that it does not bend so easily.
10. You can create a template or pattern to make the bevels with oxycut
Hard to say with the way he built that one, but, current 70-120k 6 rod style susp has the option of springs or a beam styled like that one, that acts as the spring as well. Very common on heavy bed units with planetaries. However they do use a rubber trunnion bushing on them., I can't see where they put anything like that in there for sure, appears to be steel on steel?. Drilling thru the frame flange is a bad idea on a good day. Guess if he wants a cheap susp, he got one. Like to see it again a year or two down the road. Be a fairly constant same old battle with wear on the axle seats, just like he had with the springs, no wear pads on axle or beams. And I'd bet his frame and or the beam has cracks shortly too.
I think that.
1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask.
2. They should use stronger solder, type 7018, 9018, 11018.
3. They must make bevels for welding and leave space between the pieces so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side.
4. For very serious jobs like these, it is necessary to apply the welding vertically upwards.
5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖....
6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius)
7. There is no need to bend the electrodes.
8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles.
9. The entire piece should have some kind of tempering so that it does not bend so easily.
10. You can create a template or pattern to make the bevels with oxycut
Pakistani number one
My man can weld. No doubt there. Killer job
Not sure if serious. There was zero weld prep done which means poor penetration and weak welds.
The reason they upgrade the suspension on these trucks so much is because they overload them. They go way past the weight rating on these trucks, seen lots of cracked frames, axles, and broken suspension from these Pakistan and Indian drivers.
Wow beatiful vary good 👍🏻💯💯
Thank you so much
I think that.
1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask.
2. They should use stronger solder, type 7018, 9018, 11018.
3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side.
4. For very serious jobs like these, it is necessary to apply the welding vertically upwards.
5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖....
6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius)
7. There is no need to bend the electrodes.
8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles.
9. The entire piece should have some kind of tempering so that it does not bend so easily.
10. You can create a template or pattern to make the bevels with oxycut
That kid can sure lay down a pretty weld❤
To,
WOW a Lovely 😍🌹 Good Your,,,
I think that.
1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask.
2. They should use stronger solder, type 7018, 9018, 11018.
3. They must make bevels for welding and leave space between the pieces so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side.
4. For very serious jobs like these, it is necessary to apply the welding vertically upwards.
5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖....
6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius)
7. There is no need to bend the electrodes.
8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles.
9. The entire piece should have some kind of tempering so that it does not bend so easily.
10. You can create a template or pattern to make the bevels with oxycut
Faltou reforço dentro da peça! Umas divisão. Fica na paz!🇧🇷
بسیار عالی و همراه با تکنیک انجام دادن که لازمه ان فقط تجربه بالای کاری است .❤
I think that.
1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask.
2. They should use stronger solder, type 7018, 9018, 11018.
3. They must make bevels for welding and leave space between the pieces so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side.
4. For very serious jobs like these, it is necessary to apply the welding vertically upwards.
5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖....
6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius)
7. There is no need to bend the electrodes.
8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles.
9. The entire piece should have some kind of tempering so that it does not bend so easily.
10. You can create a template or pattern to make the bevels with oxycut
Fantastic engineering
I wasn’t expecting the Richard petty blue paint.
This is probably how the Europeans view Americans when they see us welding without a rebreather.
Literally seen this like 5000 times it’s called a walking beam suspension every cement truck in the world or log truck has one. What the fuck are you talking about?
Всё конечно хорошо, но столько сделано не правильно
Без поперечной связи кронштейнов разорвет раму.
Серьёзно?
я недумаю что твой коментарий их нтересует ))))) ....на машину нужно погрузить 70т вот пожалуйста !
Even in west, began with solid wooden wheels for trucks, solid rubber pads screwed on. So pneumatic tyres do most of work.
This method is Excellent! This is called the hard bar! Used for Extreme Duty Applications! The truck chassis frame or axels will fail! Solution is stop the overloads! Hey driver you better install air suspension ride seats! Remember money is the evils! But do in for The Lord God! Love your brother.
I think that.
1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask.
2. They should use stronger solder, type 7018, 9018, 11018.
3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side.
4. For very serious jobs like these, it is necessary to apply the welding vertically upwards.
5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖....
6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius)
7. There is no need to bend the electrodes.
8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles.
9. The entire piece should have some kind of tempering so that it does not bend so easily.
10. You can create a template or pattern to make the bevels with oxycut
@@RobertoParra-k8yare you aware that there are other places in world besides where you live?
Getter done!!!
Жёсткие типы эти типы😄😄😄
Очень глупая идея! Шасси будет испытывать бешеные нагрузки на дороге. Такой транспорт только по рельсам пускать😅
глупый ты 😂 поработай на китайских 4-х осниках все поймешь
Хз, у нас на прицепах-роспусках лесовозы ездили, вроде норм было всё
@@_kycok_xom9ika_608И на первых КрАЗах такие подвески были и работали норм
I think that.
1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask.
2. They should use stronger solder, type 7018, 9018, 11018.
3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side.
4. For very serious jobs like these, it is necessary to apply the welding vertically upwards.
5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖....
6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius)
7. There is no need to bend the electrodes.
8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles.
9. The entire piece should have some kind of tempering so that it does not bend so easily.
10. You can create a template or pattern to make the bevels with oxycut
Whi do you comment the same unfer every comment?@@RobertoParra-k8y
This is only going to move the failure to the next weakest point, probably the wheels, axles, or chassis.
If it isn't overloaded i think it will be just fine. leaf springs are difficult on an incline, i have almost turned over a trailer on two occasions, both times in a field, due to the lower wheel sinking, and shifting the weight onto the lower spring. This looks like it will be quite stable.
I think that.
1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask.
2. They should use stronger solder, type 7018, 9018, 11018.
3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side.
4. For very serious jobs like these, it is necessary to apply the welding vertically upwards.
5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖....
6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius)
7. There is no need to bend the electrodes.
8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles.
9. The entire piece should have some kind of tempering so that it does not bend so easily.
10. You can create a template or pattern to make the bevels with oxycut
Неожидал увидеть гайковëрты 😳
How's are they twisting on different levels of each wheel?
а теперь покажите как это всё работает? и на сколько хватит
Add 4 airbags and you get a amazing smooth ride.
The best that can say whether this is good or not are the user themeselves
This guy right here knows what he's doing when it comes to welding I've seen them well shit that shouldn't be welded crankshaft camshafts blocks all kinds of stuff rear differentials all kinds of stuff he is a talented Machinist..... 😮😮😮😮😮😮
Я не понял они вместо ресор это поставили,а я ждал куда ани подушки ставить будут а ани не будут,взрыв мозга
Yo creo que.
1. Deberían usar mejores elementos de protección personal: guantes botas, careta para soldar, delantal de cuero y mascarilla.
2. Deberían usar soldadura más fuerte, tipo 7018, 9018, 11018.
3. Deben hacer biseles para soldar y dejar espacio entre las piezas para que se peguen o adhieran correctamente las piezas. Y más cuando sólo se puede soldar por un lado.
4. Para trabajos muy serios cómo estos es necesario aplicar la soldadura de forma vertical ascendente.
5. Para trabajos tan serios cómo estos es necesario aplicar intercalados los cordones de soldadura: a la una, a las seis 🕕 a las nueve 🕘, a las tres 🕒... A las dos 🕑, a las siete 🕖....
6. Para trabajos cómo estos es necesario precalentar un poco el área dónde se va soldar (60 grados celsius)
7. No hace falta doblar los electrodos.
8. Para trabajos tan delicados cómo estos es mejor aplica la soldadura en movimientos de letra (C) o en círculos.
9. Toda la pieza debería llevar alguna especie de temple para que no se doble tan fácil.
10. You can create a template or pattern to make the bevels with oxycut
@@RobertoParra-k8yони лучше тебя узнает все,не переживайся.диванный эксперть😂
Подушки оставь неразвитым странам, у которых денежек побольше.
@@RobertoParra-k8y
Ну наговорил дядя))))))
Just because you can do something doesn't mean its a good idea 😂 Theres a reason why trucks have springs and are not solid...
Low bed Tokyu Japan 16 tyre laughing seeing this video.....❗️
They love to see how far they can go with the weight and height. Got to admit they don’t take NO for an answer
Steel plate from old ships probably.....nothing like a bit of recycling..
This was going on all over the world when men worked and repaired the trucks where they broke down. Unfortunately by the time all the Professionals get their cut, theres not much left to cut so the truckers, fitters and ironworkers have to bear the brunt. After this "when they have so much money,it no longer matters to them" the greedy pigs will give the hauliers a choice. Go into debt to buy new plant and keep within the regulations. Then you can put 10 or more of these men on welfare . These are gifted and talented men, the kind of men who are invaluable when all the false plastic trash, falls to bits.
Я тащусь от этих ребят.
А может просто меньше грузить надо? Следующей будет рама. Потом еще что то...
😂да они эту раму за три дня востановят
Use a lebel on that surface is totally stupid
Great engineering ❤
I think that.
1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask.
2. They should use stronger solder, type 7018, 9018, 11018.
3. They must make bevels for welding and leave space between the pieces so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side.
4. For very serious jobs like these, it is necessary to apply the welding vertically upwards.
5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖....
6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius)
7. There is no need to bend the electrodes.
8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles.
9. The entire piece should have some kind of tempering so that it does not bend so easily.
10. You can create a template or pattern to make the bevels with oxycut
Dude was spot welding with sunglasses 😎 . . . . 😖😵💫
Yes it was
Nice.
Thank you! Cheers!
👍👍👍👍
Did anyone else notice that in the beginning the truck had 4 wheels per side and in the finish product, it had 2 wheels per side? Did the truck go from heavy duty to medium duty?
Cad card board aided design!
Using a spirit level on a truck wheel...eh. is the truck plumb...nuts
An incredible thing that I know is profitable, but here in Brazil it would be difficult to happen, a lot of negative bureaucracy here
❤Nice
very stable for 402m straight road drag
So now the axle housings break! And weve seen plenty of those repairs havent we!
Great camera work. Is that 1/2" or 3/4" plate
If you remove the leaf spring and install the support bar,
Failure to cushion the impact may cause the axle shaft to break.
I've seen a lot of videos on this video where a truck's axle shaft is broken and repaired.
Great engineering dont get me wrong....but there is no give in that beam ....that will cause all kinds of problems in the future...
Вся амортизация за счёт маятника😅
Great now they can overload it without worrying 😂
Yo creo que.
1. Deberían usar mejores elementos de protección personal: guantes botas, careta para soldar, delantal de cuero y mascarilla.
2. Deberían usar soldadura más fuerte, tipo 7018, 9018, 11018.
3. Deben hacer biseles para soldar y dejar espacio entre las piezas para que se peguen o adhieran correctamente las piezas. Y más cuando sólo se puede soldar por un lado.
4. Para trabajos muy serios cómo estos es necesario aplicar la soldadura de forma vertical ascendente.
5. Para trabajos tan serios cómo estos es necesario aplicar intercalados los cordones de soldadura: a la una, a las seis 🕕 a las nueve 🕘, a las tres 🕒... A las dos 🕑, a las siete 🕖....
6. Para trabajos cómo estos es necesario precalentar un poco el área dónde se va soldar (60 grados celsius)
7. No hace falta doblar los electrodos.
8. Para trabajos tan delicados cómo estos es mejor aplica la soldadura en movimientos de letra (C) o en círculos.
9. Toda la pieza debería llevar alguna especie de temple para que no se doble tan fácil.
10. You can create a template or pattern to make the bevels with oxycut
I think that.
1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask.
2. They should use stronger solder, type 7018, 9018, 11018.
3. They must make bevels for welding and leave space between the pieces so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side.
4. For very serious jobs like these, it is necessary to apply the welding vertically upwards.
5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖....
6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius)
7. There is no need to bend the electrodes.
8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles.
9. The entire piece should have some kind of tempering so that it does not bend so easily.
10. You can create a template or pattern to make the bevels with oxycut
😂yessir
They just moved the weak link from the springs to the frame or axle housings.
Made in Pakistan 🥴🥴🥴🥴😏😏😏
Следующим этапом будет рама как у экскаватора. Жёстче чем у бульдозера. Потом ось лопнет - поставят с вагона железнодорожного. Тормоза не держат - уберут вообще. Будут тормозить об другой авто. Идеи даром, пользуйтесь.
I think that.
1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask.
2. They should use stronger solder, type 7018, 9018, 11018.
3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side.
4. For very serious jobs like these, it is necessary to apply the welding vertically upwards.
5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖....
6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius)
7. There is no need to bend the electrodes.
8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles.
9. The entire piece should have some kind of tempering so that it does not bend so easily.
10. You can create a template or pattern to make the bevels with oxycut
@@RobertoParra-k8y
это прошлый век какие фаски какие скосы
😀😀😀😀😀😀😀😀😀😀нано технологии типа:и так сойдёт
Следующий этап усилить позвоночник водителя 😂😂😂
No overloaded greedy people design this way 😂😂
Так мосты вообще можно к раме прикрутить и в шины песок насыпать
At least one worker on the crew had safety slippers
So they are using the tyres as airbags. Won't work very well unless they reduce pressure.
Sai nguyên lý sẽ ảnh hưởng đến hỏng hệ thống khung dầm
THIS PEOPLE HAS A LOT OF SKILLS , THERE PURPOSE ACTUALLY DURABILITY N LESS MAINTENANCE COST . THEY'RE GOOD , I ADMIRE THIS PEOPLE .
make a video of a result after installing your fabricated product
How is he getting a full penitration weld without bevilng the edges on the beam it should have been done with multiple passes
Mọi thứ sẽ gãy vụn sau khi làm việc này. Thảm Hoa
I think that.
1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask.
2. They should use stronger solder, type 7018, 9018, 11018.
3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side.
4. For very serious jobs like these, it is necessary to apply the welding vertically upwards.
5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖....
6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius)
7. There is no need to bend the electrodes.
8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles.
9. The entire piece should have some kind of tempering so that it does not bend so easily.
10. You can create a template or pattern to make the bevels with oxycut
I wonder how you took out the disks after cutting them out and then hammering them into the thing.
I think that.
1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask.
2. They should use stronger solder, type 7018, 9018, 11018.
3. They must make bevels for welding and leave space between the pieces so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side.
4. For very serious jobs like these, it is necessary to apply the welding vertically upwards.
5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖....
6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius)
7. There is no need to bend the electrodes.
8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles.
9. The entire piece should have some kind of tempering so that it does not bend so easily.
10. You can create a template or pattern to make the bevels with oxycut
Ingin Melihat Ketika Truk Bermuatan Seperti apa
I think that.
1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask.
2. They should use stronger solder, type 7018, 9018, 11018.
3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side.
4. For very serious jobs like these, it is necessary to apply the welding vertically upwards.
5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖....
6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius)
7. There is no need to bend the electrodes.
8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles.
9. The entire piece should have some kind of tempering so that it does not bend so easily.
10. You can create a template or pattern to make the bevels with oxycut jhjjb
I'm watching intensive and 1 thing found out is there is no lubricant pot hole for the bearing that was fatal error it can't last long .
Absolutely no PPE, especially for eyes. I bet the injury rate is awful
Life is cheap in some parts of the world.
Ограничить скорость в 30км/в с такой подвеской.
120
I think that.
1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask.
2. They should use stronger solder, type 7018, 9018, 11018.
3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side.
4. For very serious jobs like these, it is necessary to apply the welding vertically upwards.
5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖....
6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius)
7. There is no need to bend the electrodes.
8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles.
9. The entire piece should have some kind of tempering so that it does not bend so easily.
10. You can create a template or pattern to make the bevels with oxycut
Следующее усовершенствование - новая двойная рама
У меня кран с такой подвеской с завода. Очень плавно едет.
That bearing definitely gonna fail in a short time. It was installed dry, then coated with grease on the outside. It doesn’t have a rubber seal to keep out dirt, sand, etc. And no grease fitting to grease it over time.
Great point!
Uma coisa incrível que sei que é rentável, mas aqui no Brasil seria difícil de acontecer, muita burocracia negativa aqui
An incredible thing that I know is profitable, but here in Brazil it would be difficult to happen, a lot of negative bureaucracy here
Great work and a good idea. 😅 I saw mechanics wearing work boots? Is that not against the law?😂😂😂❤. A prestressed box girder and free floating tires. The male Karen's are jealous. 😂😂😂.
Exactly!
Первые кразы с такими подвесками и еще сельхоз прицепи были роу-6
Big whoop who wants to live forever?
I think that.
1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask.
2. They should use stronger solder, type 7018, 9018, 11018.
3. They must make bevels for welding and leave space between the pieces so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side.
4. For very serious jobs like these, it is necessary to apply the welding vertically upwards.
5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖....
6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius)
7. There is no need to bend the electrodes.
8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles.
9. The entire piece should have some kind of tempering so that it does not bend so easily.
10. You can create a template or pattern to make the bevels with oxycut
Мерседес нервно курит. А чё так можно было😂 жаль не показали как всё это едет
Едет норм Первые КрАЗы с такой подвеской были
I think that.
1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask.
2. They should use stronger solder, type 7018, 9018, 11018.
3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side.
4. For very serious jobs like these, it is necessary to apply the welding vertically upwards.
5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖....
6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius)
7. There is no need to bend the electrodes.
8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles.
9. The entire piece should have some kind of tempering so that it does not bend so easily.
10. You can create a template or pattern to make the bevels with oxycut
@@RobertoParra-k8y не пиши свои глупые советы под каждым комментарием
It will Crack the axle under heavy load
No impossible
@@Mechanicalact His frame will crack with the way they attached it, beam or hangar will likely crack around the welds, hard to say which one goes first.
Nao vai ficar dura demais a suspensão ? A ponta da carcaça vai sofrer todo o impacto...
I think that.
1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask.
2. They should use stronger solder, type 7018, 9018, 11018.
3. They must make bevels for welding and leave space between the pieces so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side.
4. For very serious jobs like these, it is necessary to apply the welding vertically upwards.
5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖....
6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius)
7. There is no need to bend the electrodes.
8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles.
9. The entire piece should have some kind of tempering so that it does not bend so easily.
10. You can create a template or pattern to make the bevels with oxycut
With lighter loads they can make more trips and save money in repairs and maintenance.
With the amount of overloaded cargo on every run, I highly doubt it.
Not sure if a group of guys in their 50's count as young man. Lmao
I think that.
1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask.
2. They should use stronger solder, type 7018, 9018, 11018.
3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side.
4. For very serious jobs like these, it is necessary to apply the welding vertically upwards.
5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖....
6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius)
7. There is no need to bend the electrodes.
8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles.
9. The entire piece should have some kind of tempering so that it does not bend so easily.
10. You can create a template or pattern to make the bevels with oxycut
The guy in the blue gown was the “young guy” I guess 😂
I understand your limited room in your shop but throwing grinding disc abrasive in your bearing surfaces and lathe beds not good for long lasting wear on your bearings and lathe bed
👏👍💪🤩