I didn't fancy unsoldering the solenoids to replace the smaller belt you can thread it around the switch contacts using dental hook or similar. It takes a steady hand and lots and lots of patience though.
I didn't solder the solenoids. I cut a thin belt and then superglued it end to end. This belt does not affect the sound. Usually the belt never breaks at the gluing site.
Спасибо, поменял ремни. Контакт сначала погнул, потом выровнял, не работало. Позвонил контакт под платой, пропаял, заработало. Ещо под прижимнымроликом щёлкнул пластмасса и ролик прижался. Сейчас работает.
Thank you very much for your help!❤ But can you advice link from eBay or AliExpress where I can order belts? And which mm 3 or 4 my belts? And how much peace’s. Thank you ❤
Hello Sir. Please let mw know how did you adjust the Level Meter L and R. Just finished to replace the belts and other minor adjustements on mine but did not understood from the Service Manual how to adjust the level meter. Mine its a bit off Thank you
I was excited at first to replace my belts on my same deck but then the welder .... I think I will try to replace them and if I broke something I will sent it to trash. Which belts must I buy ?
that was a very helpful video, i replaced belts bu unsoliding the circuit too.
I've done a few of these since this video. I'm much faster at it now 😊
Quick reverse is more than Auto Reverse. Quick reverse means, the decks can reverse very quick when blank lead tape is detected
I didn't fancy unsoldering the solenoids to replace the smaller belt you can thread it around the switch contacts using dental hook or similar. It takes a steady hand and lots and lots of patience though.
"horrible goopy stuff" wow thats an understatement 😅 that shit is the bane of my existence 😂
Nice detailed video. Thank you .
thank you very much. Your tips are priceless
I didn't solder the solenoids. I cut a thin belt and then superglued it end to end. This belt does not affect the sound. Usually the belt never breaks at the gluing site.
I found a really easy way to remove the Rubber "gloop" is to use "Elbow Grease" Degreaser on a cue tip and follow that with alcohol,
Спасибо, поменял ремни. Контакт сначала погнул, потом выровнял, не работало. Позвонил контакт под платой, пропаял, заработало. Ещо под прижимнымроликом щёлкнул пластмасса и ролик прижался. Сейчас работает.
Thank you very much for your help!❤ But can you advice link from eBay or AliExpress where I can order belts? And which mm 3 or 4 my belts? And how much peace’s. Thank you ❤
www.ebay.co.uk/itm/326027388831
Thank you very much 😊@@ANTandTEC
Плоский 110 мм, тонкий 65-70 мм.
Hello Sir. Please let mw know how did you adjust the Level Meter L and R.
Just finished to replace the belts and other minor adjustements on mine but did not understood from the Service Manual how to adjust the level meter. Mine its a bit off
Thank you
afaik the speed adjustment are these 2 potentiometers on the board where all these microswitches are.
I was excited at first to replace my belts on my same deck but then the welder .... I think I will try to replace them and if I broke something I will sent it to trash. Which belts must I buy ?
The solder work is easy if you have an iron, they are large pads.
For the belts just search "AIWA AD-WX929 belts" 😊
Плоский 110 мм, тонкий 65-70 мм.
Where can to buy pinch rollers for AIWA AD-WX929?
Adf 1000!
Дизайн сильный!!!