Wow, I like that. Could the heating coil be be detachable to add, say 2m of flexible (and thick) copper cables in between ? This could be much more versatile if used for plumbing/brazing. Would anybody have a thought on this beyond "don't make any loops in your cable" ?
Excelente trabajo ya lo había visto en el canal de Recalibrando hace años me gustaría saber que voltaje y frecuencia tiene a la salida. Y como calculaste los capacitores. Saludos....
those were cold solder joints to the copper tubing. Don't heat the solder, heat the tubing, and then melt the solder. Those will fail. great idea, not the best material (wood).
How long can this run? What is the max temperature it can achieve? I want to make this and use it to melt gold with crucible. Will this be good enough for this Operation? Thank you.
If you use exterior tubing with wire centered in it, wouldn't you have an adjustable coil? You just need to make sure fluid can flow through the tube and over the wire! Cheers! If you try it, please let me know how it goes! It might be an interesting idea with interesting results! 🙏 Added input.... You may be able to use plastic and coil it around the wire before you insert it into the tube! That should allow for flexibility and coolant flow!
আযান শোনা যাচ্ছে এমন আযান শোনানি মনের মধ্যে একটা কথা আমি বুঝতে পারছি আমাদের কাছে একটা সোমপত রয়েছে পৃথিবীর শ্রেষ্ঠ হল আজান আল্লাহ তাআলা উনার কে কে আযান দিয়েছেন আমার মুখেও দান করেন
Nice job man thanks for sharing, i see the machine is tripping due to over-current, if one gets a welder with 100% duty cycle is it going to prevent the OC trip error? again thank you for this nice and informative video.
I suspect you should size them to give a similar resonant frequency response to what the welder normally would operate at. Anything at that frequency or lower should be OK, just don't add too much and drag things down below 20kHz, for the love of all young ears around you.
@@zinckensteel Note that a capacitor has a rated maximum current. Usually around 50 amps. Increasing the current means more capacitors in parallel and adjusting the values to resonate. Overcurrent the capacitor and it will quickly blow out, maybe in seconds if you try 200 amps!
Amazing project would like a part's list so that i can make one for a knife smiting shopas i belong to a shop that gives free classes to veterans and could really use this machine
ok, one thing i would advise ,although probably not nessesary, i would turn your machine on first before just putting your metal in your coil, all of the induction heaters i built had (latch up), problems because of too much or too big of a peice of metal being put in the coil. turning on my induction heaters first, then slowly putting in my metal did help, but....all of my induction heaters i built were built using mosfets, i did get latch ups, and going through seval mosfets. but this idea of using igbts may all together may not matter, (perventing latch ups all together), i have one of these types of welders, mines from harbour freight,i think i'll try this at some point, i think it's a great idea thanks for the video, one thing also i was wondering is, how thick is the metal on the handle of your hammer? i coulnd'nt tell.
Apa alat ini akan di jual? Dan brp harga jualnya jika di jual. Kami tertarik dgn barang ini. Mohon di informasi KPD kami. Kami sangat butuh dengan barang ini.🙏🙏🙏
You don't need to worry too much about the capacity of the welding machine because most IGBT electronic welding machines can be used. Thank you for watch
That's an idea! Awesome! And you didn't even repurpose the original welder, just add functionality to it! Ingenious.
Thank you!
@@D.creativedoes the induction heat cupper? or it just for iron?
@@hamidsoltan1433 Just for iron, stainless steel, some types of brass. No good for copper and aluminum.
A part list would have been nice but ogtherwise, tremendous job on the project. welders being cheap these days will make this a popular video !!
WOW ITS SO SIMPLE, YOU MADE A NEW MACHINE WOWWWW SIMPLE SIMPLE
Прекрасная работа, очень хорошая идея,👍
Putting capacitors inside of copper pipe, gave me much satisfaction feeling. 😁
Your job is really good
@@Jules.D
If the magnetic field goes out some voltage raise.. high volt low amps..
Красиво! Умничка! Золотые руки!
Nice! The best in this project is that the welding function still remains.
Nice job. Induction heaters are rare tool builds. We shared this video on our homemade tool forum last week 😎
Thank you
ขอขอบคุณ
Mantab, matur nuwun ilmunya, salam dari 🇲🇨
Parabéns Pará você que Deus abençoe muito muito você permanessa sempre assim
Parabéns!!belíssimo trabalho.
Gostei imenso da aula sobre a transformação/utilização de um aparelho de soldar por arco elétrico mais, a função de indução. Imensamente grato.
Thank you. Wishing you all good things
Excellent project. Can you provide design data (frequency, L and C calculation) ?
Wood used to be used as an electrical insulator long ago, but to see it inside a welder is 'surprising'!
yo pensé que decia LGBT el modelo la máquina por los colores jjjajajaj
Excelente video Sr.
Am so definitely trying this. I was to buy induction machine but not anymore.
Biurifu video
Did you tried this?
???
Take my credit! You are great!
Thank you 🙏 ❤
Es sencillo,para el que tiene conocimiento,mas no para los que no sabemos nada
❤❤❤❤excelant work dear.❤❤❤❤
Excelente trabajo
Very interesting video, well done!
Hello my friend
It was great
I have a question
I want the induction coil to be one or two turns
What should I do
Thanks
Very nice!
pm me can you to install do sola paint of charger..
Opa deixa eu perguntar consigo colocar um cabo de 10 milímetros junto nessa ponteira para a máquina para ficar móvel
Wow, I like that.
Could the heating coil be be detachable to add, say 2m of flexible (and thick) copper cables in between ?
This could be much more versatile if used for plumbing/brazing.
Would anybody have a thought on this beyond "don't make any loops in your cable" ?
Thanks for this great idea, I have a question:
Is it work for heating a copper rod?
It's very important to me. Please answer my question.
Nice build.
Would it work as well with 6 inch heating coil?
it will work but have to change the number of turns of wire
Thanks for watching the video
pm me can you to install do sola paint of charger..
nice video guys ❤
Very very good ❤❤❤❤
Very nice, thank you!!!👍👍👍
How do I know how many capacitors to put?
The more the better
Excelente trabajo ya lo había visto en el canal de Recalibrando hace años me gustaría saber que voltaje y frecuencia tiene a la salida. Y como calculaste los capacitores. Saludos....
Great idea sir 🙏
Very good job
those were cold solder joints to the copper tubing. Don't heat the solder, heat the tubing, and then melt the solder. Those will fail. great idea, not the best material (wood).
Nice project
How long can this run? What is the max temperature it can achieve? I want to make this and use it to melt gold with crucible. Will this be good enough for this Operation? Thank you.
This needs quite more enery because gold is not ferromagentic. Only Ferromagnetic metal could heated up.This works similar like an inductive cocker.
Да подойдёт в графите.1300°с
I understand that a welder provide high energy (apmerage), but what about the needed high frequency?? How do you get it??
The welding machine's frequency of 35-40 kHz is enough to heat the iron. If you adjust the frequency to 100khz, the welding machine may be damaged
If you use exterior tubing with wire centered in it, wouldn't you have an adjustable coil? You just need to make sure fluid can flow through the tube and over the wire! Cheers! If you try it, please let me know how it goes! It might be an interesting idea with interesting results! 🙏 Added input.... You may be able to use plastic and coil it around the wire before you insert it into the tube! That should allow for flexibility and coolant flow!
Nice idea buddy 👍 😉
@@anwin85alon Not sure what you're asking me! Can you elaborate?
Ferfec
How many turn of copper pipe and the capacitors connected directly to the copper pipe no other electric connection?? Please advice thank you
It would be more efficient to use the Peltier cell, it cools better and does not use water and a pump.
Very nice, thank you!!!
Thử xem nó hàn ống đồng được ko anh?
The plastic calipers are amazing 🤐
Parabéns.
thx bro.,very good job!
Çok iyi. Gerçekten. Teşekkür ederim. Çok daha güçlüsü olurmu?
Is it heat copper tube
আযান শোনা যাচ্ছে এমন আযান শোনানি মনের মধ্যে একটা কথা আমি বুঝতে পারছি আমাদের কাছে একটা সোমপত রয়েছে পৃথিবীর শ্রেষ্ঠ হল আজান আল্লাহ তাআলা উনার কে কে আযান দিয়েছেন আমার মুখেও দান করেন
Hi friend, good job! What abuot if you let the workpiece heat long time, will it melt? Which real power your device delivers? Thanks.
Nice job man thanks for sharing, i see the machine is tripping due to over-current, if one gets a welder with 100% duty cycle is it going to prevent the OC trip error? again thank you for this nice and informative video.
Okay, good luck to you
$$$$$$$
Very nice machine but what does 3 kilowatt hour consumption value mean or what does it mean my friend
does the induction heat cupper? or it just heat iron? please answer
Amazing idea!
Máy này nấu vàng được không bạn ? bạn chế một máy giống này và giá bao nhiêu mình cần nó !
Khoang 200 usd $ nau chay duoc vang.nhung can cai noi mini co can dai de cam cho bot nong
No - only ferromagnetic material can be heat-up
Great awesome👍🙏🇧🇷
can you melt brass with this heater? a small piece of brass
Another question please, can I put any capacitor I find? Because I didn't find any capacitors 220V 10 UF
Máy hàn 4igbt công suất thực 160a có làm đc ko bạn
Được bạn nhé!
Is that Works on Copper welding ?????
if using a 200 or 250amp welder will different size capacitors be needed in series on the heater pipe?
I suspect you should size them to give a similar resonant frequency response to what the welder normally would operate at. Anything at that frequency or lower should be OK, just don't add too much and drag things down below 20kHz, for the love of all young ears around you.
@@zinckensteel thank you for talking the time to give me some info
@@zinckensteel Note that a capacitor has a rated maximum current. Usually around 50 amps. Increasing the current means more capacitors in parallel and adjusting the values to resonate. Overcurrent the capacitor and it will quickly blow out, maybe in seconds if you try 200 amps!
Bro actually I have one question,here water place,add collent oil mainly use colent oil in car engine,it is sutable are not send detailse.
Amazing project would like a part's list so that i can make one for a knife smiting shopas i belong to a shop that gives free classes to veterans and could really use this machine
I have a question please, can the device burn if I turn it on and do not put anything to heat it?
Itu switch dpt utk menghidupkan/mematikan apa bos? Thank...
Switch to turn water pump and cooling fan on and off
Trima kasih banget atas jawabannya.semoga sukses selalu
Nice❤
It appears this can only be done with an IGBT inverter type welder. My cracker box won’t do☹️
consider yourself lucky that your welder is saved from such a modification.
Bạn có bán máy đó ko ? Giá nhiêu ?nếu hợp lý tôi mua ạ !
Good 👍🏽
Itu kapasitor di seri terhadap coil heater ya bos?
Yes!
❤❤❤❤❤
Is it same Frequency with induction heater?
Hello sir you are selling also or given idea
Why does the clock only light up when there is metal? The yellow indicator light turned off because it was too hot.
He turned it on and then off himself. You can hear the switch sound
Mua đồ bơm quạt tản nhiệt đó ở đâu
How is the current feedback controlled ? Usually is from secondary and now is disabled
it is not. that's why buy the proper tool if you need it.
@@modorangeorge4991 lol was sarcastic comm' 😂
Can we increase Coil Diameter Aprox 15 CM & Coil number 20-30 then its work or not ??
Máy này bao nhiêu tiền vậy anh
1,6tr nha bạn
1,6tr nha bạn😁
Parts list? Schematics please
Gracias por compartir
Cara muito técnico.
ok, one thing i would advise ,although probably not nessesary, i would turn your machine on first before just putting your metal in your coil, all of the induction heaters i built had (latch up), problems because of too much or too big of a peice of metal being put in the coil. turning on my induction heaters first, then slowly putting in my metal did help, but....all of my induction heaters i built were built using mosfets, i did get latch ups, and going through seval mosfets. but this idea of using igbts may all together may not matter, (perventing latch ups all together), i have one of these types of welders, mines from harbour freight,i think i'll try this at some point, i think it's a great idea thanks for the video, one thing also i was wondering is, how thick is the metal on the handle of your hammer? i coulnd'nt tell.
أنا أتساءل كيف تستطيع مكثفة 20مكروفاراد تمرير تيار 142 أمبير ؟؟؟!!!!😮😮😮😮
@@RamanSaou Two in parallel. But still is definitely a choke point in the circuit! Maybe that is why he shuts the machine off so quickly!
Brilliant. !
Здравствуйте.Какая мощность получилась.
Mình muốn làm một cái vậy được không
Very nice, but those welds could be way better. Not enough heat ? try some flux. Cheers.
a ver !! siempre se debe de usar calibre fino de muchos hilos es mas eficiente
BAD BAD : Smoke in the machine in 25 secunder
Hello, what is the amps or watts of the inverter welding machine used in this video?
150A Welding Machine
máy hàn motfet chế vậy dc hog ad
Được bạn nhé!
It can melt cast iron??
Only for heat treatment and forging process
How to buy capacitor because in my area is not unavailable.pls help
How many watts does this induction heater produce? I'm trying to compare it with the 15kW unit for $880 USD.
😂😂😂 no more than as a welder device.
Apa alat ini akan di jual? Dan brp harga jualnya jika di jual. Kami tertarik dgn barang ini. Mohon di informasi KPD kami. Kami sangat butuh dengan barang ini.🙏🙏🙏
Làm cho tôi một bộ được không bạn
how mouch of kw we can get from this machins . thankyou
You don't need to worry too much about the capacity of the welding machine because most IGBT electronic welding machines can be used. Thank you for watch
BRAVO !!!
Thanks
Belum ada produksi pemanas yang langsung jadi kayak gitu.ingin beli buat alat tambahan di bengkel
А конденсаторы последовательно или паролельно катушкам как их расчитывать
Please can anyone guarantee this works and can be used reqularly without damaging in any degree the welding machine.