Variable Power Supply 0-60V 5A Using TIP41C

[@azharmukhi5894]

Thank you sir for providing such useful videos on your chennal, keep doing the great work 👍.

[@TARIQLAB]

Welcome

[@EdemirMedeiros]

Valeu amigo, seus vídeos são ótimos e sem enrolação! Obrigado por compartilhar conosco🖒

[@angkerbir5176]

is this a variable DC to DC circuit...?
and can it work for switching with a DC voltage of 54 volts 3 amperes...?

[@مهدیجبیری]

Friends, the transistor gets very hot, be sure to put a suitable heat sink and fan to dissipate the heat!

[@TARIQLAB]

👍

[@omarjewel7305]

Is it necessary to use MUR4100 here? or can any other 4 amp diode be used instead?

[@TARIQLAB]

Any

[@KennethAzemafac]

what is the minimum input voltage, and maximum input current for this circuit

[@فاضلصانت]

هل تشغل الماطور ٧٧ عليه ؟

[@EdemirMedeiros]

Tóp de + Mais um inscrito 🖒

[@abderrahmanebakir6613]

How can the same input current be the same output current?

[@ZidanAzzumar]

Can I use other diodes besides Mur4100?

[@herritrisnadi7528]

Selamat siang oom, tegangan masuknya masih volt ac, atau sudah dc..terima kasih dan sukses selalu.

[@raspberrypi7098]

Filter capacitor required at input and output. 50 k pot needs to be wire wound potentiometer. Need bigger heatsink.

[@TARIQLAB]

I gave filtered supply no need extra filter, at output when we decreasing voltage will not decreasing same time because of residual charge in the capacitor

[@mohdjulfukar1343]

Good information sir

[@konsultankeluarga2399]

Can you show me the speed control circuit for the DC motor of an electric bicycle?

[@mdanisuddin700]

Supply dc v dena hai ya ac 220 dena hai

[@TARIQLAB]

DC 60v

[@sandipsharma800]

Lm317 kya use kar sakte hai.60 volt k liye

[@TARIQLAB]

Nahi that is only 37v 1A

[@omarjewel7305]

If I use two tip41c transistors in parallel in this circuit is it possible to get 10 amp?

[@TARIQLAB]

Yes, but use bigger heatsink

[@omarjewel7305]

​@@TARIQLABThanx...

[@josealexandrealbuquerqueca8693]

Gostei , mas posso substituir o diodo por qual da minha cidade não tem o Mur4100

[@TARIQLAB]

Sem problemas, você pode usar qualquer diodo

[@PrabhuPrabhu-po8ss]

84v 10amp auto cutoff for ebike how to ready ?

[@Voltx-channel]

What is the use of a diode in this circuit?

[@TARIQLAB]

To cancel the back emf generated by motor or coil from load side

[@Dr.JitendraKumar-Official]

BD243c use kar sakte hai

[@TARIQLAB]

Yes

[@petruk_pejuang_keadilan]

How if diode change with capacitor? It still work?

[@TARIQLAB]

Diode is just to block back EMI generated by inductive load

[@huutainguyen0103]

I want to increase the output load current, what should I do?

[@TARIQLAB]

Use high amp transistor

[@huutainguyen0103]

What about diodes?

[@TARIQLAB]

Diode is not important it is just for cancel emf generated by load, any number u can use

[@huutainguyen0103]

Ok thank you

[@GogleTrip]

What about potensio 50k, can we use it ?

[@maxcell8077]

Posso colocar uma tensão negativa ?

[@TARIQLAB]

No

[@virusmada6069]

What is the maximum current limit for this circuit ?

[@TARIQLAB]

5A

[@virusmada6069]

@@TARIQLAB What if I wanted to increase the current ؟

[@TARIQLAB]

With this transistor not possible, TIP120 8A

[@Anand-karnataka]

क्या भाई सिर्फ पावर सप्लाय के ही वीडियो बनावोगे ?

[@EdemirMedeiros]

Muitos aquí, lévam em média 40 minutos prá fazer um vídeo desse!😅😅😅😅😅🖒🖒🖒

[@leonmorajosueabiram1925]

Si entran 35 v a la entrada los valores resistivos cambian verdad

[@TARIQLAB]

Half value

[@Jetlee-ph]

Thanks alot sir

[@TARIQLAB]

Welcome

[@sandipsharma800]

Input me kaitna voltage diye hai.

[@TARIQLAB]

60

[@horacio374]

El potenciometro es B20K.Ayuda no me regula.Algo que hice mal?.Muchas gracias.

[@TARIQLAB]

use una resistencia de 100 ohmios entre el pin central del potenciómetro y la base del transistor,

[@AdamTheBot]

Will 100K pot work ?

[@TARIQLAB]

Yes

[@moniruliislam6494]

Can we use this regulator for 775 dc motor??

[@TARIQLAB]

Yes, but bigger heatsink required

[@horacio374]

Buen video.Lo hice pero no se' que conecte mal ya que el Potenciometro no me regula.Le coloque' uno de 20 Ohmn que es el que tengo.Ayuda por favor.Muchas gracias.

[@Dr.JitendraKumar-Official]

Diode 5408 work karega

[@TARIQLAB]

Karta hai

[@Dr.JitendraKumar-Official]

@@TARIQLAB thank you

[@moniruliislam6494]

Can we use 60v 3ah adapter?/

[@TARIQLAB]

Yes

[@moniruliislam6494]

Thank you for your suggestion

[@innovativeart3854]

I want 220V AC to DC power supply circuit

[@ientuhoanglinh]

good jod

[@TARIQLAB]

TQ

[@LuisCastro-nz7it]

hola tariq estoy intentando hacer un dispositivo pero no se como hacerlo, me podrías ayudar?, es un buz, seria éste

[@LuisCastro-nz7it]

ua-cam.com/video/gztpAYlpjn0/v-deo.htmlsi=QwNfi5Uo-IOVFKqZ

[@LuisCastro-nz7it]

min. 11.36

[@LuisCastro-nz7it]

ua-cam.com/video/gztpAYlpjn0/v-deo.htmlsi=cAy9Hs6XgA-uY_25

[@nurdwiyanti9949]

Saya membuat ini tetapi kenapa tegangan tidak stabil ?

[@TARIQLAB]

Check potentiometer

[@mari_kitaberusaha]

Di gunakan untuk AC 220 bisa TDK

[@TARIQLAB]

No

[@MunawarReja]

😅😅😅😂tai gajebo

[@solihinadoy3205]

In put +DC

[@TARIQLAB]

Yes 60v