Thank you. FInally, fixed my printer through this video. Its been months since I've been dealing with paper jam. Only to find out my toddler throw a pencil inside. Thanks.
Thank you. Our 2134 developed some kind of paper jam that the control panel kept insisting was "out of paper". Your video gave me the confidence to unscrew the damned thing and find a piece of (redundant?) hard black tape sticking out of a kind of sump for, I suppose, ink left over from head cleaning. Perhaps the tape once had a sponge attached? Who knows. Anyway, I squelched it back down, screwed it all back together, and now it works fine. De momento, por lo menos.
Very good information brother ❤❤❤ i just flip my hp 3223 and from that the ink come out from the scan area it was just an residual ink which printer throw it to clean the print head frist i was scared that cartirage leaks and i open it with 4 teeath t-9 l n key but two of them dont get open and now i have to buy the t-10 l n key 😢😢
Please show how to get under the pickup roller and clean the input area of label paper where labels have become stuck and can't be removed from the little underside door
I wish you could have shown how to take apart the cartridge carriage case because that's what I was planning to replace in my printer because for some reason my tri color led keeps blinking though I have tried putting new cartridges as well.
1:53 what is the black piece on the left of the underside of the printer for? My wife took it apart and I was unsure of where it went until looking at this video
Thanks for the suggestion, I have a similar model and will see if I can remove it to post video. I'm sorry I didn't think of it when making this video.
So happy I ran across your video on HP printer disassembly. I was doing a interior clean on my HP1220c Deskjet and while cleaning around the cartridge slide bar with some alcohol the "encoder strip" got dislodged on one end so I took it out. Replaced it and printer heads are not moving. Saw on your video that the "encoder strip" must be threaded through the cartridge slider assembly. I am sure that is my problem. Was hesitating as since it is called "encoder strip" I thought perhaps it may be important as to which end you put in to the machine. I t can be installed I think in either direction physically but I wondered if the strip has a "Left and Right Ends" making it important as to which end you attached to the left end of the machine or right side. Or is it "non-directional" as far as re-installing it??? Thanks.
Hi. Thanks for watching. Yes, it usually is important, but if the amount of blank space is same on each side, it won't matter which side is right or left. It's an older model, I'm not sure how it is supposed to be. I'll research and if I find out, I'll update you
Does it do that for copy or printing? If for both, you may need to check cartridge and make sure all packing protective film tape is removed from cartridge. Clean the contacts on the printer. They are golden dots in the back of the carrier, where it touches the golden contacts on cartridge. If it is doing blanks for prints only and copy is fine, settings need to be checked on the device from which the job is being sent from.
@@303electronics it was always fine until a month ago. I think I have it fixed now though. My problem now is after I took it apart to do the cleaning now I can't use the scan bed because all lights start flashing. Yes I checked the ribbon cables.
I haven't used mine in a while and now it seems to be clogged! Where would I start to get the ink flowing again? Could you help me please if you find the time?
Can please do a video of removing pickup roller? I need to change the grey rubber on the pickup roller but i don't know how to deattach it😭....my printer is hp deskjet ink advantage 2545, the inside part is the same with the printer u did in this video
Hello your video is great. I'll open up printer with this to see what causing problem..."door open error" while i close the door, open again and closed, tried so many times but no solution. if u have any idea please reply. Another question timer strip got ink on it. Can it be culprit? Thanks 😊👍
Hi. Yes, since you will be opening up the printer, clean the strip from ink since it will cause errors. Make sure you are very gentle with the strip to avoid tearing it or pulling out of the sensor area. The latch that is there for the "door open" sensor may be stuck or broken. Should be a simple fix. Let me know how that goes. Thanks for your feedback. Have a great weekend!
@@29monir oh no. No way. You will ruin it. Just use a simple cleaning solution or water on a napkin or paper towel. Never use nail polish remover for any parts on printer. Too harsh, I think.
I have hp printer with scanner. I want to use only scanner. I want to disconnect printer from mainboard only scanner i want to use. Is it possible to work the scanner even the printer flex from catridge and the connection related to printer i want to disconect from mainboard. Is it possible to work the scanner?
Everything is right but sir, I found that in this type of printer has paper jam issue occurs and side where there is no functioning board and where the cartrige rest. There I found one trigger type of mechanizem that does not go back to its right position when printer get a bit old. everything is working and I try to place that trigger back to its position it work smoothly but sometimes it get same issue. can you make a video upon it sir, if you could solve it then we will very happy. Thank you
j havent used mine for like 2 months, now i check back theres a lot of black ants nesting in the printer and they already reach the mirror part, if you dont mind can you do tutorial on how to open up the mirror and clean it?
I have uploaded a video with instructions. The printer I use is similar to yours, use torx screw size 10 tip to remove screws. I hope it helps. ua-cam.com/video/HM-G9AKJd9g/v-deo.html
Sir my printer hp 2135 deskjet scanner comes to left side and get stops at one end while scanning, it is not scanning any documents, but printout is coming ok , xerox is also very light colour not deep black , suggest me what is the problem
I just got my printer full of ants inside , and it scare me if there would be electrical damage , don't know how to open as im a woman, this video would be very useful 🙏
Hi Sir. I am happy that i found your video. I bought the same printer and when they deliverd mine i saw broken black metal material. I saw to your video that the metal is just holding the wire. Is that part important? And i haven't use it yet since i am thinking to return it. Thanks
Hi. Thanks for your support.. I'm not sure which part that is. I would replace if something that looks like a part falls out of box, unless it is a packaging piece.
@@303electronics I just researched the name of that mini tiny part and they called it as ferrite ring core. thanks for the quick response sir. Stay safe
Hello sir how can i fix the printer which the cartridge bangs to hard. I think the thing behind the cartridge like cartridge wall is damaged. What is the name of it, i wanted to buy but i dont know the name of it. It looks like plastic strip.
Hi. Yes, it is a timing encoder strip. It can be replaced or fixed. If it ripped,, you can fix it by putting a little piece of tape on both side of the end of the strip. Make a small hole in tape where the hole is originally, and reattach the strip. Thanks
Hi. Usually there is a way on hp printers, however this printer does not have a screen and i do not know how to reset printers without display. I'm sorry. I hope someone may know more and will post a reply.
Hi man, i just replace my HP 2135 tricolor cartridge with a new one last night. Before placing it into the printer slot, I firstly test the ink cartridge using some tissue and the ink is good. But after i print test some pages the color ink doesn't come out at all. I check the printing preferences/print properties, the option is already at color printing. You have an idea what went wrong? Thanks
I'm sorry for the trouble. Is it a new HP ink cartridge or aftermarket or "remanufactured"? Often times the remanufactured ones from eBay or Amazon may have a problem, rarely though. If ink cartridge feels like it is filled and seems to be in good condition, check the golden contacts area on the ink cartridge and the printer. Make sure no tape residue is there. Please let me know if this helps. You can also try tapping ink on a moist napkin or paper towel.
The ink cartridge is brand new, opened from a sealed box i bought from a store. I already tried tapping the cartridge into a tissue several time and they're good, the colors are bright and clear, so I think theres nothing wrong with the ink cartridge. I'm guessing the problem is on the inside of the printer, but I don't know which part it is. It's a 5 years old HP 2135 though.
I'm sorry there is a problem. Try changing the plug and see if that helps. Also it is possible that the connection to power supply inside the printer may be loose.
Sir will it work with any timing encoder strip. Because there are many strip showing on online shopping. My printers strip is not broken but some of the dark part on the strip has Some scratches and disappeared. Thats why i thought my cartridge is not moving gently and cannot print at all.
hey can u help me. i have hp deskjet 2135 and i buy brand new ink but as soon i replaced my ink , the black ink light blinking while the colour just fine. can u help me how to fix that?
Hi. Did you buy aftermarket or HP brand? Most likely the cartridge is faulty or you didn't remove protective packaging like tape on contact area. Please let me know.
@@303electronics i buy hp brand. i tried on my friend printer , it works just fine but when i put my black ink in my printer, the black ink light just blinking and i cant print anything cause the device is "busy"
Could you tell? Which size of screwdriver you had used to open this printer. Tell in mm size because I want to buy this as a screwdriver. Please reply as soon as possible.
@@303electronics could you suggest me? I don't know about T10 size. I have link please www.amazon.in/dp/B082WGQL8R/ref=cm_sw_r_cp_awdb_imm_9KA9B13VF6C7RJT71P09?_encoding=UTF8&psc=1
@@303electronics T 10 means How many mm? Please suggest exact size in that link www.amazon.in/dp/B082WGQL8R/ref=cm_sw_r_cp_awdb_imm_9KA9B13VF6C7RJT71P09?_encoding=UTF8&psc=1
@@303electronics I found T 10 size. Is this right size buy for hp 2131 printer. Kindly check this size please www.indiamart.com/proddetail/torx-screw-driver-20511812333.html
It has a wireless card attached to the main board. Yes, you can physucally remove it, but I do not know if printer will see it as an error and if it will continue working.
Are any of the buttons or lights flashing? If all lights seem to be acting normal, the button control board may need adjusting, maybe wiring or connections.
@@303electronics Oh thats it. Thanks! one more thing, is this the same as in other 2300 variants? i have 2336 and it looks totally identical. Thanks again!
[09/10, 11:07 pm] Ravi: Hello sir i have a problem for my printer [09/10, 11:09 pm] Ravi: Please help [09/10, 11:13 pm] Ravi: When i power for my printer with a tester it indicates light everywhere in the circuit and printer does not start.. Its fault of mother board or adapter
Unfortunately the starter ink cartridges have very little ink, however it is possible that the setting of printing of photo nay have been set to very high quality and that is why it used up ink so fast.
Thank you. FInally, fixed my printer through this video. Its been months since I've been dealing with paper jam. Only to find out my toddler throw a pencil inside. Thanks.
Glad you got it fixed. Thanks for sharing. Have a great weekend!
My girlfriend did exactly the same. Kind of funny that people around the world are dealing with the same issues. :'D
the same here... my toddler put a pen in the paper feed... just fixed it!
Thank you. Our 2134 developed some kind of paper jam that the control panel kept insisting was "out of paper". Your video gave me the confidence to unscrew the damned thing and find a piece of (redundant?) hard black tape sticking out of a kind of sump for, I suppose, ink left over from head cleaning. Perhaps the tape once had a sponge attached? Who knows. Anyway, I squelched it back down, screwed it all back together, and now it works fine. De momento, por lo menos.
Thank you so much! My 2 yr old somehow unhooked a very small piece and this video helped me put everything back where it belongs.
I'm glad you were able to fix the printer. Thank you for sharing. Have a great weekend!
Thank you!!!! Just fixed it. My daughter of 3 put a pen inside the paper feed apparently!
thanks to your video I now have easier access to the pickup roller :)
You're welcome! Have a great holiday!!!
Can you do a video of how to put everything back together? I am having trouble putting back the input tray.
Me too. Have you find out how to actually put the tray back?
How did u put back 😩
😅
Sorted my 2632 printer with this video. Great video with detailed information.
Thanks. Have a great day!
wow..thanks for the video man, managed to removed clogs inside the printer case and running now
Good work! Thank you very much for sharing. Have a great weekend!
Very good information brother ❤❤❤ i just flip my hp 3223 and from that the ink come out from the scan area it was just an residual ink which printer throw it to clean the print head frist i was scared that cartirage leaks and i open it with 4 teeath t-9 l n key but two of them dont get open and now i have to buy the t-10 l n key 😢😢
Please show how to get under the pickup roller and clean the input area of label paper where labels have become stuck and can't be removed from the little underside door
You will need to remove the top of the printer to get inside. It is still not too easy to do so. Use tweezers to remove stickers from roller.
EXCELLENT! Exactly what I was looking for.
Thank you. Have a good day!
Thank you so much. Thanks to your video I´ve found that the worst enemy for these printers is child´s pencils.
Glad I could help! Have a great weekend!
I wish you could have shown how to take apart the cartridge carriage case because that's what I was planning to replace in my printer because for some reason my tri color led keeps blinking though I have tried putting new cartridges as well.
1:53 what is the black piece on the left of the underside of the printer for? My wife took it apart and I was unsure of where it went until looking at this video
Grazie mille, ottimo lavoro, spiegato bene...grazie 👍👍👍
You're welcome! Thank you for the feedback!
Excellent video! Congratulations! Thank you..
I appreciate your feedback! Have a great day!
If you could continue trying to remove the paper pickup roller that would be great. I am trying to change mine and cannot get it out.
Thanks for the suggestion, I have a similar model and will see if I can remove it to post video. I'm sorry I didn't think of it when making this video.
So happy I ran across your video on HP printer disassembly. I was doing a interior clean on my HP1220c Deskjet and while cleaning around the cartridge slide bar with some alcohol the "encoder strip" got dislodged on one end so I took it out. Replaced it and printer heads are not moving. Saw on your video that the "encoder strip" must be threaded through the cartridge slider assembly. I am sure that is my problem. Was hesitating as since it is called "encoder strip" I thought perhaps it may be important as to which end you put in to the machine. I t can be installed I think in either direction physically but I wondered if the strip has a "Left and Right Ends" making it important as to which end you attached to the left end of the machine or right side. Or is it "non-directional" as far as re-installing it??? Thanks.
Hi. Thanks for watching. Yes, it usually is important, but if the amount of blank space is same on each side, it won't matter which side is right or left. It's an older model, I'm not sure how it is supposed to be. I'll research and if I find out, I'll update you
Great video, but how do I get the carriage out? I'm having trouble where I get ghost images even with a new cartridge....
Does it do that for copy or printing? If for both, you may need to check cartridge and make sure all packing protective film tape is removed from cartridge. Clean the contacts on the printer. They are golden dots in the back of the carrier, where it touches the golden contacts on cartridge. If it is doing blanks for prints only and copy is fine, settings need to be checked on the device from which the job is being sent from.
@@303electronics it was always fine until a month ago. I think I have it fixed now though. My problem now is after I took it apart to do the cleaning now I can't use the scan bed because all lights start flashing. Yes I checked the ribbon cables.
I haven't used mine in a while and now it seems to be clogged! Where would I start to get the ink flowing again? Could you help me please if you find the time?
New subscriber 👍 thank you.
Can i repair the AC power adapter please?
Thank you! I haven't tried to repair the power adapter. I usually replace it if I can find one on the market.
Can please do a video of removing pickup roller? I need to change the grey rubber on the pickup roller but i don't know how to deattach it😭....my printer is hp deskjet ink advantage 2545, the inside part is the same with the printer u did in this video
Its very hard to remove the pickup roller. Did you try cleaning it first?
@@303electronics yes i did, and it still refuse to roll in the paper....is it impossible to be repaired?
Thanks your video was very helpful.
You're welcome! Thanks for the feedback. Have a great day!
Hello your video is great. I'll open up printer with this to see what causing problem..."door open error" while i close the door, open again and closed, tried so many times but no solution. if u have any idea please reply. Another question timer strip got ink on it. Can it be culprit? Thanks 😊👍
Hi. Yes, since you will be opening up the printer, clean the strip from ink since it will cause errors. Make sure you are very gentle with the strip to avoid tearing it or pulling out of the sensor area. The latch that is there for the "door open" sensor may be stuck or broken. Should be a simple fix. Let me know how that goes. Thanks for your feedback. Have a great weekend!
Where is door open sensor please 🥺
Can is clean strip with nail polish remover?
@@29monir I'm not sure, have to look into it when I'm at the shop tomorrow. Should be on the left or right side of door just inside the door opening.
@@29monir oh no. No way. You will ruin it. Just use a simple cleaning solution or water on a napkin or paper towel. Never use nail polish remover for any parts on printer. Too harsh, I think.
I have hp printer with scanner. I want to use only scanner. I want to disconnect printer from mainboard only scanner i want to use. Is it possible to work the scanner even the printer flex from catridge and the connection related to printer i want to disconect from mainboard. Is it possible to work the scanner?
Unfortunately, that isn't possible.
Thank you.. got much help.
You're welcome! Thanks for the feedback!
Thank you so much, I solved my issue after learning from this video. :) 🤝
Everything is right but sir, I found that in this type of printer has paper jam issue occurs and side where there is no functioning board and where the cartrige rest. There I found one trigger type of mechanizem that does not go back to its right position when printer get a bit old. everything is working and I try to place that trigger back to its position it work smoothly but sometimes it get same issue. can you make a video upon it sir, if you could solve it then we will very happy. Thank you
Hi. Thanks for the suggestion. I will see if I have a similar model on which I can make a video. Have a great day.
Awesome video, worked just as good on a 2722.... Thanks!!!
That's awesome! Thanks for letting us know thatbut works on 2722. Have a great weekend!
Very informative video bro, tq
You're welcome! Thank you very much for your support! Have a great day!
Is this the same way to take apart the HP 2755 ALL IN ONE PRINTER ?
j havent used mine for like 2 months, now i check back theres a lot of black ants nesting in the printer and they already reach the mirror part, if you dont mind can you do tutorial on how to open up the mirror and clean it?
I will try to demonstrate it on a similar model and will post a video.
@@303electronics thank you so much
I have uploaded a video with instructions. The printer I use is similar to yours, use torx screw size 10 tip to remove screws. I hope it helps.
ua-cam.com/video/HM-G9AKJd9g/v-deo.html
Thanx u have saved a brother
Thanks for the feedback! Have a great evening!
Sir my printer hp 2135 deskjet scanner comes to left side and get stops at one end while scanning, it is not scanning any documents, but printout is coming ok , xerox is also very light colour not deep black , suggest me what is the problem
I just got my printer full of ants inside , and it scare me if there would be electrical damage , don't know how to open as im a woman, this video would be very useful 🙏
I'm glad its helpful. Thanks.
Err how do you put it back together I did all this clips the cat rips on and it isn’t going on
hi 303 Electronics. what do you think is the reason why the bottom edge of the paper has ink stain when i print on the minimum margin on the bottom?
ser can i ask what will i do if its problem is output tray error and i cannot find the sensor for that HP 2320
thank you so much its fixed
That's great! Thanks for the feedback.
My 2160 printer has just started squeaking while printing. Any ideas what could be causing this? Thanks!
It can be the rod on which the carrier slides, may need grease lube.
@@303electronics thank you! What type of grease should I use?
Hi Sir. I am happy that i found your video. I bought the same printer and when they deliverd mine i saw broken black metal material. I saw to your video that the metal is just holding the wire. Is that part important? And i haven't use it yet since i am thinking to return it. Thanks
Hi. Thanks for your support.. I'm not sure which part that is. I would replace if something that looks like a part falls out of box, unless it is a packaging piece.
@@303electronics I just researched the name of that mini tiny part and they called it as ferrite ring core. thanks for the quick response sir. Stay safe
Hello sir how can i fix the printer which the cartridge bangs to hard. I think the thing behind the cartridge like cartridge wall is damaged. What is the name of it, i wanted to buy but i dont know the name of it. It looks like plastic strip.
Hi. Yes, it is a timing encoder strip. It can be replaced or fixed. If it ripped,, you can fix it by putting a little piece of tape on both side of the end of the strip. Make a small hole in tape where the hole is originally, and reattach the strip. Thanks
@@303electronics thank you so much sir.
Please Can I get your Instagram id or facebook id. Because i want to learn more from you sir.
Hello i really need to print an important paper however my 2130hp deskjet is bliking orange even the ink is full plz help
Great work
Thank you! Have a great day!
thank you , hp2620 this replace
worked
hello there, is there anyway on how to reset this printer to factory default? thanks
Hi. Usually there is a way on hp printers, however this printer does not have a screen and i do not know how to reset printers without display. I'm sorry. I hope someone may know more and will post a reply.
@@303electronics thankyou verymuch your video was a big help, just opened my printer and check if i can reset something. But i see nothing.
Hi man, i just replace my HP 2135 tricolor cartridge with a new one last night. Before placing it into the printer slot, I firstly test the ink cartridge using some tissue and the ink is good. But after i print test some pages the color ink doesn't come out at all. I check the printing preferences/print properties, the option is already at color printing. You have an idea what went wrong? Thanks
I'm sorry for the trouble. Is it a new HP ink cartridge or aftermarket or "remanufactured"? Often times the remanufactured ones from eBay or Amazon may have a problem, rarely though. If ink cartridge feels like it is filled and seems to be in good condition, check the golden contacts area on the ink cartridge and the printer. Make sure no tape residue is there. Please let me know if this helps. You can also try tapping ink on a moist napkin or paper towel.
The ink cartridge is brand new, opened from a sealed box i bought from a store. I already tried tapping the cartridge into a tissue several time and they're good, the colors are bright and clear, so I think theres nothing wrong with the ink cartridge. I'm guessing the problem is on the inside of the printer, but I don't know which part it is. It's a 5 years old HP 2135 though.
Bro my printer is not turning on.... power button showing low level light....the problem is in adaptor or circuit...
I'm sorry there is a problem. Try changing the plug and see if that helps. Also it is possible that the connection to power supply inside the printer may be loose.
Hai boss
Where I can buy timing strip scale for this model HP Deskjet 2336
Sir after i reset my printèr why all indicator light is blink what is the problem?
It wants to do an alignment. Press ok to continue
Sir will it work with any timing encoder strip. Because there are many strip showing on online shopping. My printers strip is not broken but some of the dark part on the strip has Some scratches and disappeared. Thats why i thought my cartridge is not moving gently and cannot print at all.
Less likely that. Try cleaning the rod on which the carrier slides and add some grease lube to it
Sir i tried but still not working.
thank you very much my brother
You're welcome! Have a great day!
Thank you very much
You're welcome! Have a great day!
do have a video with a pca label circuit board on a printer... when i copy in the scanner the size of print is small
I currently do not. Sorry.
Sir my printer is not working no power light on no scanning
How to fix it?
Hi any idea, mine feeds 2 paper, 1 at a time and then it stops, and it keeps rolling and wont eat the paper.
Hi. Make sure the papere is not pushed too far, also check to make sure there is n;t anything at the bottom of the tray.
hey can u help me. i have hp deskjet 2135 and i buy brand new ink but as soon i replaced my ink , the black ink light blinking while the colour just fine. can u help me how to fix that?
Hi. Did you buy aftermarket or HP brand? Most likely the cartridge is faulty or you didn't remove protective packaging like tape on contact area. Please let me know.
@@303electronics i buy hp brand. i tried on my friend printer , it works just fine but when i put my black ink in my printer, the black ink light just blinking and i cant print anything cause the device is "busy"
i need it because my gecho is stuck thank yuo foe this vidio
Could you tell? Which size of screwdriver you had used to open this printer. Tell in mm size because I want to buy this as a screwdriver. Please reply as soon as possible.
Hi. Its torque screw size 10. T-10 or T10. It is star shaped.
@@303electronics could you suggest me? I don't know about T10 size. I have link please www.amazon.in/dp/B082WGQL8R/ref=cm_sw_r_cp_awdb_imm_9KA9B13VF6C7RJT71P09?_encoding=UTF8&psc=1
@@303electronics T 10 means How many mm? Please suggest exact size in that link www.amazon.in/dp/B082WGQL8R/ref=cm_sw_r_cp_awdb_imm_9KA9B13VF6C7RJT71P09?_encoding=UTF8&psc=1
@@303electronics I found T 10 size. Is this right size buy for hp 2131 printer. Kindly check this size please www.indiamart.com/proddetail/torx-screw-driver-20511812333.html
@@prathameshvartak3105 Yes! T-10 torx. The indiamart link is correct, Amazon link is not the item you need. Thanks.
My roller is not given any space to put a paper inside it can u please tell me how to fix it 😭😭
The roller should spring freely back and forth. If it isn't going in, there can be something in the way that makes it stick to one position.
Could you tell me if it is possible to physically remove the WiFi?
It has a wireless card attached to the main board. Yes, you can physucally remove it, but I do not know if printer will see it as an error and if it will continue working.
Believe it or not , there is a dead cockroach just under the glass panel. This is why my alignment is failing. I don't dare to take the printer apart.
Excellent!
Thank You
You're welcome! Have a great weekend!
Does it work in e8 error?
Run this video and just go backwards to put together
Well goodness he almost took it all apart,lol,why did he stop,run out of time,lol😂😂😂
That was the point. 🙂
Did you mention anything about the waste ink pad? Sorry if you did and I didn't notice it.
Thanks
You're welcome! Have a great day!
Hi , my printer does not respond to copier button also and does not print from pc also, can anybody tell me the reason?
Are any of the buttons or lights flashing? If all lights seem to be acting normal, the button control board may need adjusting, maybe wiring or connections.
Amerika se aaya h kiya be
Where is the waste tank?
There isn't one on this printer.. There are pads that are on the very bottom of the printer that absorb waste ink.
@@303electronics Oh thats it. Thanks! one more thing, is this the same as in other 2300 variants? i have 2336 and it looks totally identical. Thanks again!
[09/10, 11:07 pm] Ravi: Hello sir i have a problem for my printer
[09/10, 11:09 pm] Ravi: Please help
[09/10, 11:13 pm] Ravi: When i power for my printer with a tester it indicates light everywhere in the circuit and printer does not start.. Its fault of mother board or adapter
Honestly, I would not be able to know. It can be power adapter, logic board, or both. I'm sorry.
Awesome
Yo see first back side
Thanks. Have a great day!
OP
Yep
Worst scam printer ever i litteraly only could print 5 pic of colour paper with brand new original 305 cartridge 2700 series
Unfortunately the starter ink cartridges have very little ink, however it is possible that the setting of printing of photo nay have been set to very high quality and that is why it used up ink so fast.
shittest printer after refilling it doest work
It could be clogged ink cartridges at the nozzles. Try cleaning bottom of ink cartridges with warm water or windex.
khoti deya mery printar de siry char geya aaaan
Thanks
Fake video
Absolutely! The printer is not even real. 😆 ....What do you mean? But thanks for watching, anyway!
Thank you
Thank you so much
You're most welcome! Have a great day!