good video and is self-explanatory so language is not a problem, one question I have for you, can you rebuild the top end of this engine while the engine is still in the frame, I want to fit a new barrel and piston and was wondering if it can be done without taking the engine out of the frame, its all down to will the top frame under the petrol tank stopping the head from rising up above the studs so it can be removed, or maybe remove the front engine mount bolts so it can fall forward to give extra clearance,
Es un excelente video amigo. Muchas gracias por compartir. Desde Colombia un saludo. Solo me quedó una duda con respecto a la silicona o sellador. ¿ Le aplicaste a la junta que va entre el cilindro y la culata? . ¿ Que tan óptimo es?
Good video man.. i am planning on splitting the case on a xr200r same engine as the one you did.. have to fix the crank barring the race of the barring is spinning inside the case is that a problem
Hello! Did you change the piston too? Or only the rings? I have the same problem, and I don't know if I have to change the piston for a bigger one or not? Thank you!
I bore the cylinder and used an oversized piston as well as the rings. If the cylinders in your bike's engine are not worn out, you may only need to replace the rings.
Hola amigo excelente video, con el arme mi moto pero cuando puse la moto en tiempo el avanzador quedo a la 1 y cuando la puse en fuego quedaba a las 2 nunca quedó con la la raya pareja de la pulsora por qué sucede esto? Gracias.
Lo siento, estoy traduciendo al español con Google Translate, así que no entiendo perfectamente lo que dices. ¿Es un problema avanzado? Sería genial si pudieras tomar un video y subirlo a UA-cam.
Complimenti vivissimi dell'Italia! Ho una honda xl125s del 1983 da rifare. Il tuo video mi sarà molto utile. Un saluto fratello himalayano!
Grazie per la visione. Grazie per il vostro continuo supporto. Per favore, vieni in Nepal quando hai una moto.
Mi piacciono gli animali selvatici. ho visto il tuo canale Guarda anche
ua-cam.com/video/9zVmkG_qaIc/v-deo.html
Здравствуйте мд18е знаком двигатель
good video and is self-explanatory so language is not a problem, one question I have for you, can you rebuild the top end of this engine while the engine is still in the frame, I want to fit a new barrel and piston and was wondering if it can be done without taking the engine out of the frame, its all down to will the top frame under the petrol tank stopping the head from rising up above the studs so it can be removed, or maybe remove the front engine mount bolts so it can fall forward to give extra clearance,
no , you can't do that way.
Es un excelente video amigo. Muchas gracias por compartir. Desde Colombia un saludo. Solo me quedó una duda con respecto a la silicona o sellador. ¿ Le aplicaste a la junta que va entre el cilindro y la culata? . ¿ Que tan óptimo es?
Si le preocupa la fuga de aceite, puede aplicar una capa delgada. No hay problema.
Good video man.. i am planning on splitting the case on a xr200r same engine as the one you did.. have to fix the crank barring the race of the barring is spinning inside the case is that a problem
thank you. It would be nice if you could replace the case, but if not there is a way to make and insert a new lace.
@@HimalayanWorkshops can I peen it?? Whit a center punch would that work
Tengo un sonido de tintineo o xomo si tuviera un valía suelto en mi honda xl 200 año 2001 pero cuando esta en baja resolución
Hello! Did you change the piston too? Or only the rings? I have the same problem, and I don't know if I have to change the piston for a bigger one or not? Thank you!
I bore the cylinder and used an oversized piston as well as the rings. If the cylinders in your bike's engine are not worn out, you may only need to replace the rings.
@@HimalayanWorkshops thank you for your help and answer!
where is workshop
great mechanic, good man
Hola amigo excelente video, con el arme mi moto pero cuando puse la moto en tiempo el avanzador quedo a la 1 y cuando la puse en fuego quedaba a las 2 nunca quedó con la la raya pareja de la pulsora por qué sucede esto? Gracias.
Lo siento, estoy traduciendo al español con Google Translate, así que no entiendo perfectamente lo que dices. ¿Es un problema avanzado? Sería genial si pudieras tomar un video y subirlo a UA-cam.
Sir pariho lng sa bulb seal at piston ring sa 155 n Honda?
May be not.
Buenas noches amigo, por qué le pones silicona al empaque de la culata?
El manual dice que use un sellador en la tapa de la culata. no una junta.
no aplique el sellador demasiado cerca del borde de la superficie del cojinete del lado derecho, ya que restringirá el flujo de aceite.
Can you tell me what kind of headlight you are using for this bike?
LED light very cheap one,thank u.
Great video! Did the larger piston cause any additional vibration due to an imbalance?
Thank you,Which piston are you planning to use in which engine?
Amazing Skills.
I'm repairing the same engine. Where do you sell those gaskets and packings
tl125s(イーハトーブ)
ありがとうございます。ガスケットは社外品を使用しました。イーハトーブもXL125ｓとほぼ同じですのでガスケットも入手しやすいはずです。ヤフオクなどではどうでしょうか？
@@HimalayanWorkshops
日本語での対応！ありがとうございます！
ほぼ互換品なんですね、初耳です
探してみます！
Looks like a hot country where you are.
What oil do you use,
10w40 or thicker?
Yes, 10w-40
How much it cost?
I want big bore kit for honda xr 125 can we have that?
Honda XL maintenance ,import parts.
Rabindra Workshop ,Kathmandu 9849252888
Hola amigo cuántos litros de aceite lleva el motor?
1litter
Поршень диаметр какои?
What's the size of the piston you're using Sir?
0.25 os
Does this bike use 6v or 12v electrics?
converted to12V
Did you use the stater and cover off of a different bike? Or did you rewind the factory one?
@@curryitr Just changed Regurator
Nice! Looks like it’s powerful enough to run an LED headlight now?
Tengo un motor similar pero no se cual es el problema la punterias de calibrar no me alcanza asta la valvula pareciera q la valvula se undio
I have disassembled the engine many times, and I am learning from repeated failures. Let's break it down first.
Location po pala boss
Excelente video aprendí mucho gracias.
Mi xl quema mucha bujía que puede ser?
¿Cuáles son los síntomas de las bujías quemadas? ¿Significa que es negro y hollín? ¿Será que el enchufe se derritió al punto de quedar inservible?
Hello, this is made in japan or brasil
Made in Japan ,Thank you.
location plz
Honda XL maintenance ,import parts.
Rabindra Workshop ,Kathmandu 9849252888
g.co/kgs/gfX6kc
nice job, ggz-👽👾👍
Good job, just like I do it.
The sound of head its too noisy..why you didint use feeler gauges for adjusting clearance of valve tappet ..noisy like tiktiktiktik
First, increase the tappet clearance a little. After running it for a while, I adjusted it. thank you.
Well done
Very helpful
FANTASTICO !!!!!!!
Solo lo cambió los anillos?? Si es así muy mal
Acabo de cambiar el anillo esta vez. Si el cilindro está dañado, aguántelo y reemplace también el pistón.
Amigo tienes WhatsApp?
WhatsApp es difícil, así que publique el video en UA-cam.