Це відео не доступне.
Перепрошуємо.
200 Series Landcruiser Headlight Upgrade: How to install Stedi LED lights in a LC200
Вставка
- Опубліковано 16 сер 2024
- A detailed look at how to upgrade every white light in a 200 series Landcruiser. Headlights, parker, reverse, number plate, map and interior light upgrade
Install requires:
Two (pair) high beam lights: HB3 (9005) Copper Head LED Bulb
Two (pair) low beam lights: H8 | H9 | H11 | H16 Copper Head LED Bulb
Two (pair) interior lights: FESTOON 28MM LED BULB
Four (2x pairs) parker/everse T10 W5W WEDGE INTERIOR LED BULB
Four (2x pairs) map/license plate lights T15 WEDGE EXTERIOR LED BULB
links:
www.stedi.com....
Contact us: info@BorderTouring.com
Disclaimer: The information contained herein should NOT be used as a substitute for the advice of an appropriately qualified and licensed professional. The information provided here is for information and demonstration purposes only. Please seek additional information and advice before attempting any installation. Border Touring take no responsibility for the use of their material for any installation of any product.
As far as the rear dome light replacement goes, you can actually remove the plastic cover and put the bulb in without taking the entire dome assembly out of the headliner. There are two small tabs on the forward side on either side of the switch. With a small screwdriver (carefully) or a thin trim tool you can pop that cover off front to back. Then you don't have to mess with the little metal thing and the bulb seats easier. also, the bulb size is fairly important, so go with what he's telling you on that.
Great video for a 200 Series Land Cruiser owner. Thanks!
Great camerawork and presentation. Don't really need 2min of roof bulb purchase drama, but right at 15min mark, more close up of just where to place the tool to remove the ceiling light fitting would be good.
Cheers Shane, I'll take the feedback and try to capture a bit more while filming. I'm still honing both my filming and editing skills so I really appreciate the comments. It is hard at times to remember what is important to see before and during installation.
Great video. I found low beam lights to provide a blotchy spread of light when setting them to get the right road coverage. Did you experience this?
Good summary, have you looked at the stedi lights that swap out the factory fog lights ?
I wonder how good they are.
The stedi fog light upgrade is incredible - great addition
Seems like the LED is installed in an angle? not 90degrees?
Was your list of required lights ^ just all the exterior lights and interior lights? Not including license plate?
Thanks mate great video
Hi, Great video, just finished installing Stedi LED's to reverse, number plate, interior map, and front door lights to my 2015 pre upodate Sahara. Your video explained it all perfectly. Question!! Do you have a video on changing out the 2 lights that are a part of the roof mounted TV monitor? Or give me a hint as to how to do it?? Also the 4 doors have lights at the bottome of the trim, any hints on getting into them to change out the globes?? Thanks in Advance.
Hi Colin, no I don't sorry. Try using a nylon pry tool like what I was using. Every light is accessible the clips just need to be pushed out of the way.
Take your time and if it feels like its going to break it probably will. If it breaks it's easy to replace or fix generally.
Good luck
@@bordertouring3265 Thanks anyway, I worked out the door trim lights, but the lenses next to the video screen are really tight in the fitting and a perfect fit so no room to get a tool under. Might need to ask at Toyota as a last resort!
Have you worked on the LC200 2017 onwards? Managed to change the bulbs ?
How much brighter would you say these bulbs were compared to original for the headlights? Are they still working well?
They are markedly better, probably 50-100% more light. Mine were terrible to start with.
They are fine, no issues so far and I haven't touched them since the install.
Low & High beam how many light watts?
Stedi don't list watts just power use in amps and output in lumens. They are both 1.6 amps at 13.6 volts. Is this what your chasing?
See:
www.stedi.com.au/copper-head-h8-h9-h11-h16-led-head-light-conversion-kit.html
And
www.stedi.com.au/copper-head-hb3-led-head-light-conversion-kit.html
Hey mate, just wondering if you had hyper flash on your indicators from changing the headlights to LED?
Mat, no. Mine is a 2012 and no issues at all
How hot do the heat sinks get? Just concerned of being too hot next to wiring under the bonnet.
I haven't had any issues yet, they have been in the car over 12 months.
The idea is to dissipate heat not to transfer it to other nearby wiring. So far so good though
Will this work on my 2013 LC based on the US spec
Yep all the same regardless of country. It's Toyota specific not country specific
Do you get any radio interference with these headlights?
No not at all. I use my lights as daytime running lights now so pretty good all around.
Great video!
Do you have a link to the lights you got from eBay please? Stedi are still out of stock
Cheers
Brodie, they broke within the week. Go for the stedi ones or look for a similar type. Another version but more expensive is light force from memory if you are super keen
Thank you! Good to know! I found some at Jaycar I’ll see how they go.
Much appreciated👍
Would these work on a 2009 land cruiser invincible
Yep easy swap. Try using the Stedi vehicle picker on their website
@@bordertouring3265 thanks for the reply but i think theyre quite expensive arent they
No my set was maybe $300 for every light. That's high, low, reverse, internal, etc. Worth looking into
@@bordertouring3265 ive seen some on ebay but u can never trust their chinese quality these look really good
Basically...... Bulb fit.
Basically you basically just basically do this. Very basic. Good video though!
Man I’ve wasted time on this video. Why would you not record the results!? Before and after type of thing. Or maybe even other LED comparisons?
Hey, I wanted to but simply put I don't have the camera gear to compare. I filmed the before and after but it didn't work out. For night filming I need much higher end camera gear.
Sorry if it was a waste, this one is an install and after I fully test the gear I will do a review.
If your thinking of doing the upgrade do it. It is markedly better.