Brother, you saved my day. I hit a railroad crossing tooo hard and the car stalled. I guess some safety auto fuel pump shutoff killed it, and now I've learned something. Thank you!
If all the sudden it cranks but won't fire after it been running fine is check the fuel inertia switch. He showed it. It's in the trunk with the red button on it. I was pounding in some tabs to hold the trunk liner panels and the vibration set it off. Reset it and started right up.
My 2001 crown Vic police interceptor is having an issue and I don’t know what the problem is. Was pumping gas and then after pumping gas it wouldn’t start, only cranked. The next day went to turn it on, all the lights dimmed just a tad bit, it has a new battery so the battery isn’t the problem and also I replaced the starter, I can hear the fuel pump but when I try to turn it on it cranks but will not start
That same thing happened to me a few months ago to my 05 mgm went to get gas wouldn’t start for hours till it did really bad idle under power I believe it was in limp mode
Just changed the fuel pump. The new one was a dud. I put a used one in and it's got power but still no start. Changed out the fuses but still no start. This is my 20th Vic and I was letting my roommate drive it so I wasn't there when it broke down. My daily driver Vic was towed from a parking lot and I'm desperately trying to get it back tonight. Paid DMV and got it insured. Now I gotta pay Ripon PD $195 for vehicle release fee. Then the tow yard to pay the tow and storage fee. My ride flaked out on me.
Mines did the same I got 07 vic i replace the FRP sensor it cut back on an was good a month later same thing happened went n got new Frp still doesn't cut on
Hey can I personally contact you and ask questions ? I’ve been struggling with getting my car to start back running I’m at a point where I have no idea what the problem is
Was carrying mass amount of weight in the trunk of crown vic, n had a slight drizzle of clear fluid draining from exhaust. Then went to drive off n the car started to slowly turn off from idling. It turns over but dont fire up?? Any suggestions
How you doing I got a 99 Mercury Grand mark that would not start but it would crank but won't start I'll change the fuel pump spark plugs coil use that and take manifold because it's a manifold screws to the spark plugs with broke so I had to put a new one on it I'll change the crankshaft sensor new battery I know I need the starter because it's trying to crank so I don't know what else to do can you help
I have a 2009 ford crown Victoria I just changed the fuel tank with pump and everything. Car cranks but wont start tried turning on several times and it has 2 gallons of gas so its not completely empty. I tried changin relays and checkin and nope still wont start.
I have a few 97 crown Victoria I have changed everything from the fuel pump and the crank shaft too the spark plugs even the cores wat else I need to do
I have a 99 crown Vic if I jump it off it’ll start and run for abt an hour r so n then shuts off I replaced the alternator but problem still exists Wht cld it be?
08 p71 New crankshaft sensor New camshaft sensor New relays New fuel pump New fuel filter Still doesn’t start but cranks, Pushed the inertia switch many times still no start
2003 Grand Maquis. I have not used it since June 2020. I was starting it once a month but got lazy and didn't start it in a few months and now it won't start. Its been in my garage. The battery is good, it turns over but won't start. I would like to start it so I can drive it to the end of my driveway have it towed away. After 390K miles it wasn't worth fixing anymore. Best car I have ever had. What should I look for? If I can fix it for free I am willing to try.
@@lukerogers4107 It just started. I ended up junking the car. It was the best car I have ever owned. Needed to many things and it just was time to retire it.
I have a 99 Grand Marquis that does not start. It appears to be a spark issue. It is different than the 07. Can't find the fuel pressure sensor and the regulator is different than than that sold by parts stores
bro i got a 2005 police vic. got codes 351-358. died suddenly on the freeway. cranks, no start. all fuses good. swapped all relays, nothing. fuel cutoff in trunk, nothing. did heavy super start in the intake, no fireup of anything. ideas bro? would rather buy a part then have to call a mobile mech.
@@Daknoca yes i did. it was #4 ignition cyl wires going into the wiring harness. looked like they had been messed with in the past. the two wires melted together and caused all the problems. i replace the wires & new connector. first it caused ALL coils to not spark, then just the #4 cyl. also the problem KILLED the new motorcraft coil i bought as a solution, so i had to return to get another new one. in the end, the new coil was bad from being fried from the wires shorting. causing the same problem. all good now!
Yoooooo so a problem happened to me one min it was running perfectly next it just cranks wont start... i tried the switch also and i replaced the fuel pump and relay and still just cranks and I can even hear the fuel pump turn on could it be a camshaft position sensor?
Its funny you say That cause my 07 just started doing the same thing as well I took my belt off my car to start. Doing my crankshaft sensor change, it got way to cold for me to do so.
Wassup man I got a issue starting up my 2008 cvpi. When I try starting it, it just cranks, on hot days it start up less than 20mins, on cold days it take 1-2 hr just to start up. Also I have leave the car on with the key but not completely on & that’s when I start waiting just so I can start it up. I changed the main issue that was on the vid but no luck
Hey my 1999 grand marquis isn’t starting. Had a blow out on my spare tire (donut) and my car cut off and wouldn’t start ever since then. What are some of the things I could check? I am not a mechanic but can’t really afford to pay someone to look at it
I just checked my fuel pump switch in he trunk and I pushed it back down so hopefully that was the issue. I have a dead battery from trying to start the car so much so I have to wait on a jump before I can see if that fixed the issue
Hi my car won't turn over a mechanic says it needs a pcm, because it's not getting fire to the spark plugs, It sounds like it wants to crank but just won't turn over.
Crazy thing is i replaced the fuel pressure regulator because of a code and after a month after installing the new regulator, no start. Wow maybe a bad part.
Ran fine for three months then wouldn't start. Replaced MAF sensor and camshaft sensor. Had towed to mechanic and it started fine for a week for them. Brought it home and wouldn't start. Then it started and worked for a week. Pulled out relay for fuel and swapped it with horn relay. Then it started. Any clues?
@@terryabel8516 the maf and cam doesn't do anything but help the car run smooth (not that dont do anything but will not be reason for car not starting)
My crown vic just cut off while driving and won't start It cranks but not starting. Found fuel pump fuse blown changed it checked the relay checked the fuel filter for blockage yet its fine No codes shown on the ecu I'll be locking for the easiest which is FRP sensor. If it won't start I'll change CKP sensor I hope that nothing happening inside the engine😢
@@FarzadFazel under the drivers seat. Going to the immobilizer. I don't remember the diagram or the color exactly. I wish you luck if you has the same issue🤕 hard to troupleshoot like this problems
Brother, you saved my day. I hit a railroad crossing tooo hard and the car stalled. I guess some safety auto fuel pump shutoff killed it, and now I've learned something. Thank you!
Im glad you found problem
If all the sudden it cranks but won't fire after it been running fine is check the fuel inertia switch. He showed it. It's in the trunk with the red button on it. I was pounding in some tabs to hold the trunk liner panels and the vibration set it off. Reset it and started right up.
Bro.. You saved me!! I was stranded with a blowout! And I hit that button in the trunk and cranked right up! Thank you brother!
Your welcome brother hope all is good
Hey man, this helped me out a lot on my 1994 crown victoria. I was about to take it in to have it checked out, but you save me lots of money.💯💯💯
Manny thanks from Houston Texas. I changed everything front the relay to fuel pressure sensor , back release switch in the truck and still jus crank
My 2001 crown Vic police interceptor is having an issue and I don’t know what the problem is. Was pumping gas and then after pumping gas it wouldn’t start, only cranked. The next day went to turn it on, all the lights dimmed just a tad bit, it has a new battery so the battery isn’t the problem and also I replaced the starter, I can hear the fuel pump but when I try to turn it on it cranks but will not start
Also the alternator is new as well
That same thing happened to me a few months ago to my 05 mgm went to get gas wouldn’t start for hours till it did really bad idle under power I believe it was in limp mode
Crank sensor
Just changed the fuel pump. The new one was a dud. I put a used one in and it's got power but still no start. Changed out the fuses but still no start. This is my 20th Vic and I was letting my roommate drive it so I wasn't there when it broke down. My daily driver Vic was towed from a parking lot and I'm desperately trying to get it back tonight. Paid DMV and got it insured. Now I gotta pay Ripon PD $195 for vehicle release fee. Then the tow yard to pay the tow and storage fee. My ride flaked out on me.
How did you fix it? Same issue with me rn
Ok@@karmaacosta
Mines did the same I got 07 vic i replace the FRP sensor it cut back on an was good a month later same thing happened went n got new Frp still doesn't cut on
Hey can I personally contact you and ask questions ? I’ve been struggling with getting my car to start back running I’m at a point where I have no idea what the problem is
Was carrying mass amount of weight in the trunk of crown vic, n had a slight drizzle of clear fluid draining from exhaust. Then went to drive off n the car started to slowly turn off from idling. It turns over but dont fire up??
Any suggestions
I have a '07 and it cranks over and immediately dies. Does it sound like your bad switch? Thanks for any advice.
That sounds like a bad pump or the fuel pressure sensor going out
I know this is super old but was it the fuel pump?
Thanks bro very helpful
How you doing I got a 99 Mercury Grand mark that would not start but it would crank but won't start I'll change the fuel pump spark plugs coil use that and take manifold because it's a manifold screws to the spark plugs with broke so I had to put a new one on it I'll change the crankshaft sensor new battery I know I need the starter because it's trying to crank so I don't know what else to do can you help
Hello will it start with a gallon of gas or no
I have a 2009 ford crown Victoria I just changed the fuel tank with pump and everything. Car cranks but wont start tried turning on several times and it has 2 gallons of gas so its not completely empty.
I tried changin relays and checkin and nope still wont start.
I have a question
I have a few 97 crown Victoria I have changed everything from the fuel pump and the crank shaft too the spark plugs even the cores wat else I need to do
how much fuel does a ford crown victoria have
I have a 99 crown Vic if I jump it off it’ll start and run for abt an hour r so n then shuts off I replaced the alternator but problem still exists Wht cld it be?
Thats your battery
Was that the problem
What’s that part called
08 p71
New crankshaft sensor
New camshaft sensor
New relays
New fuel pump
New fuel filter
Still doesn’t start but cranks,
Pushed the inertia switch many times still no start
2003 Grand Maquis. I have not used it since June 2020. I was starting it once a month but got lazy and didn't start it in a few months and now it won't start. Its been in my garage. The battery is good, it turns over but won't start. I would like to start it so I can drive it to the end of my driveway have it towed away. After 390K miles it wasn't worth fixing anymore. Best car I have ever had.
What should I look for? If I can fix it for free I am willing to try.
You figure this out, I’m having the same issues
@@lukerogers4107 It just started. I ended up junking the car. It was the best car I have ever owned. Needed to many things and it just was time to retire it.
Mine is not starting uma switch that part out tumarrow I hope it ain't the fuel pump
where is this on a 2000 crown vic LX?
I have a 99 Grand Marquis that does not start. It appears to be a spark issue. It is different than the 07. Can't find the fuel pressure sensor and the regulator is different than than that sold by parts stores
Furl pressure is on railing above the injectors on the left side if you looking at the engine from the front
bro i got a 2005 police vic. got codes 351-358. died suddenly on the freeway. cranks, no start. all fuses good. swapped all relays, nothing. fuel cutoff in trunk, nothing. did heavy super start in the intake, no fireup of anything. ideas bro? would rather buy a part then have to call a mobile mech.
FPS fuel pressure sensor
Watch video
My 05 is doing the same thing I thought crankshaft sensor would save the day I was wrong.. Did you figure it out yet?
@@Daknoca yes i did. it was #4 ignition cyl wires going into the wiring harness. looked like they had been messed with in the past. the two wires melted together and caused all the problems. i replace the wires & new connector. first it caused ALL coils to not spark, then just the #4 cyl. also the problem KILLED the new motorcraft coil i bought as a solution, so i had to return to get another new one. in the end, the new coil was bad from being fried from the wires shorting. causing the same problem. all good now!
Changed my fuel pump was running fine turned it off parked it an went to go turn it on an it cranks but doesnt wana start?
Could be timing chain. If so don't keep trying to crank it because it could bend the valves in the engine.
Yoooooo so a problem happened to me one min it was running perfectly next it just cranks wont start... i tried the switch also and i replaced the fuel pump and relay and still just cranks and I can even hear the fuel pump turn on could it be a camshaft position sensor?
Did u change fuel pressure sensor on the railing like I had mention in video
Its funny you say That cause my 07 just started doing the same thing as well I took my belt off my car to start. Doing my crankshaft sensor change, it got way to cold for me to do so.
My battery died after trying to start my car. Its like your not getting fuel nor spark type of symptoms
mine was doing the same thing , crank no start, and after replacing relays i figured out i had a bad fuel pump switch in the trunk
Wassup man I got a issue starting up my 2008 cvpi. When I try starting it, it just cranks, on hot days it start up less than 20mins, on cold days it take 1-2 hr just to start up. Also I have leave the car on with the key but not completely on & that’s when I start waiting just so I can start it up. I changed the main issue that was on the vid but no luck
Would say try your idle air control valve
Also how cold is it where you are at
Problem was Not the "fuel pressure rail", but LACK OF GAS.
Filter or pump
Hey my 1999 grand marquis isn’t starting. Had a blow out on my spare tire (donut) and my car cut off and wouldn’t start ever since then. What are some of the things I could check? I am not a mechanic but can’t really afford to pay someone to look at it
Does it make noise when trying to start
First is battery as always though
TheMumbojumbo32 no. It turns over like normally and it will act like it’s out of gas. Like it’s trying to start but no fuel making it.
I just checked my fuel pump switch in he trunk and I pushed it back down so hopefully that was the issue. I have a dead battery from trying to start the car so much so I have to wait on a jump before I can see if that fixed the issue
Hi my car won't turn over a mechanic says it needs a pcm, because it's not getting fire to the spark plugs,
It sounds like it wants to crank but just won't turn over.
Crazy thing is i replaced the fuel pressure regulator because of a code and after a month after installing the new regulator, no start. Wow maybe a bad part.
I'm going through cranking issues right now are you free to talk?
Yeah
What is that part called?
fuel cut off switch or inertia switch
Great vid thanx
Do u still work on vics?
Yes
Damn didn't even think you'd respond I been having trouble with mine
@@nolifenikki what's problem
My car just shut off a few times and when I turn it over it clicks
Is your battery good? And when does it turn off and how long does it stay on for
My car fuse box is not the same as yours my fuel pump relay is the block third one to 0:34
I think i have this sme problem on my 2007 ,i chanced the fuel pump and filter and even tried started fluid but still nothing
John Moore same problem with my 07 new fuel pump,crank sensor, and safety neutral switch
@@tylersutton9547 wow that’s crazy
@@A1FBG_Mexico it was a ground wire…
@@tylersutton9547 where at? Having same issue with my 2010. Replaced pump. Swapped relays. Pump is kicking on. Turns over. But won't start
@chriskent3923 I was told it was and ground wire in the wiring harness by the fire wall. I took the car to an electrical shop…
I think that what wrong with mind 🤔 it did the same thing
I got a 97 vic I just changed fuel pump fuel filter fuel relay and still won't start I'm clueless stressing bad please help what else can I do
Crankshaft sensor?
Where is that located?? Please tell me
Hello where is that located
I need some help mins doing the same thing
And when I hit the switch it started to messing with my speed dashboard and my mileage
Can we talk to mumbojumbo 32?
Yes how can I help you?
@@TheMumbojumbo32 we have a 2004 crown v that will start one day and not the next. Can we call you?
Ran fine for three months then wouldn't start. Replaced MAF sensor and camshaft sensor. Had towed to mechanic and it started fine for a week for them. Brought it home and wouldn't start. Then it started and worked for a week. Pulled out relay for fuel and swapped it with horn relay. Then it started. Any clues?
@@terryabel8516 well what does it do when trying to turn key?
@@terryabel8516 the maf and cam doesn't do anything but help the car run smooth (not that dont do anything but will not be reason for car not starting)
Bro I’ve changed pressure sensor and fuel pump and fuel filter
I have a question about mine is there any why I can contact you
Just lmk on here is fine
My crown vic just cut off while driving and won't start
It cranks but not starting. Found fuel pump fuse blown changed it checked the relay checked the fuel filter for blockage yet its fine
No codes shown on the ecu
I'll be locking for the easiest which is FRP sensor.
If it won't start I'll change CKP sensor
I hope that nothing happening inside the engine😢
Did you ever get started again
@@georgesexton5731 yep. I found a disconnected wire under the driver seat.
@@asimalharbi8796 do you know wire it was?
@@FarzadFazel under the drivers seat. Going to the immobilizer. I don't remember the diagram or the color exactly. I wish you luck if you has the same issue🤕 hard to troupleshoot like this problems
@@asimalharbi8796 having the same problems with my 2002 interceptor but I have been hearing that I need to check around for bad wires
I have a 97 Crown Victoria that I would like to sell as is
Is this Carl from AutoZone
What's up
Bro I really need you please get back to me 🙏🙏🙏🙏🙏🙏🤔
Whats up
I have a 2011 crown Vic just came from outside it won't start everything comes on
Background noise, incomplete sentences, jittery picture.
I'm having same problem with my 2004 uhg I need help
Trust me when i tell u reprogram your key thank me later
I need help with my vic
?
@@TheMumbojumbo32 I figured it out
@@DJsimplyMusicOfficial Care to share??