I built the same thing almost. The only difference is I used a TP4056 with protection. I wired the negative ends together like you did and the positive directly to battery holes on the TP4056 then to the on/off switch then to the light and fan and you could always add a fuse and make a hole on the side to change it without ripping it apart. The reason I didn't use the charger here is I have several of them and most of them are way over. You only want 4.2v constant voltage and constant current and all of mine tested 4.7v and similar which killed my batteries. The batteries here have to put out a constant drain of 5.5 amp while the flashlight is on. This is counting the fan.
I rounded up most of the materials to attempt building this flashlight. But, am missing the battery charging port at base of light and the exact size of uPVC tube & reducer. Please supply this for me.
Hey i never seen that type of drill bit over here or at the hard wares is that a special chineese drill bit? Cause if it takes that kind of drill bit how much in u.s dollars for one & what web page to find that bit etc
I think I got a problem that will take a Creative mind so I came to the right place. I balt a MOPAD 2018 model.My head lights on Bright are not enough to see dim setting is more of a joke! Any ideas that will not cast me a lot I paid 1,300$ for it so I'm out of cash and majer problems driven home from work. Any ideas I would be Much Appreciated!?!?!😀
Y aurait tilleul possibilités de faire une vidéo avec la fabrication d'une belle lampe torche de 100w avec module 12v->35v avec un potentiometre permettant de faire varier la luminosité de la led avec une batterie de 12v rechargeable et 18650 Merci à vous et continuer tout ce que vous faite 😃😃
Very good
I'm Your very very favorite fan
I built the same thing almost. The only difference is I used a TP4056 with protection. I wired the negative ends together like you did and the positive directly to battery holes on the TP4056 then to the on/off switch then to the light and fan and you could always add a fuse and make a hole on the side to change it without ripping it apart. The reason I didn't use the charger here is I have several of them and most of them are way over. You only want 4.2v constant voltage and constant current and all of mine tested 4.7v and similar which killed my batteries. The batteries here have to put out a constant drain of 5.5 amp while the flashlight is on. This is counting the fan.
You its king engineering😁😁😁🏆🏆🏆🏆🏆🏆🏆🏆🏆🏆🏆🏆
Nice torch
Желаю благополучия много новых проектов!!!
Wow very nice👏👏👏👏
Very nice looks like Chinese hand granade
so nice Flashlight
Very nice Sir
😮😯😯😯😯 amazing idea you have
very good is the video I really liked the idea like from RD
Very good ...excellent work ...
oooralesss, muy chida idea, felicidades...
nice video
Voce tem ideias fabulosa gostei.
Fantastic work, dude! 😃
I made a really similar one, but with a 10w LED and 3s batteries. 😃
where did you buy the led?
@@robertindabuilding2876 I bought it locally. But you can find them easily on AliExpress, Banggood, maybe even Gearbest and so on. 😊
Good job buddy...well I'm going to do this first..
Excelente trabalho ...
super bright 👍 good idea
U R MY 1 OF FAVURITE UA-camR BRO...I WISH GO AHEAD....
Good work ⚒
Wish i could get a work shop like his one😪
Good job.
Nice kenh sang
Thanks for making this torch very useful for me
Crazy scene Resident Evil, congratulations bro...
This is awesome 👍
Wow bro you have a very nice camera love from Pakistan😎😎😎😎😇😇😇😇
Hi Also Watch my channel #diyelectronicandhack
I actually want to say that..
Great work but how much does it cost
Крутий фанарік мені понравився корпус
Awesome
Awesome video
Thanks I was making a powerful torch and you did it for me
Would it possible for you To do the same for scuba diving?
from Bangladesh
saludame porfa me gustan tuss videos
He is a genius
You have to add some vents for air flow.
Nice ducks
Wonderful Torch sir 👌👌👌👌😍😍😍😍😍
Nice flashlight kep it
up💜💜👍
please please tell which tools like driller cutter ....you are using for your tasks ...
Super bright.
great Job
I rounded up most of the materials to attempt building this flashlight. But, am missing the battery charging port at base of light and the exact size of uPVC tube & reducer. Please supply this for me.
Which plastic it will use for hiding the joint 🤔🤔🤔
Hey i never seen that type of drill bit over here or at the hard wares is that a special chineese drill bit? Cause if it takes that kind of drill bit how much in u.s dollars for one & what web page to find that bit etc
i saw this thing ''+ DC 3.7V 20W LED Chip'' in your BOM please tell me that from where did you get this led i want it so.
U r always good.
Good idea
Olá vídeo muito bom!👍
Abraço 😷
What is with the fan? it blow's in a closed housing?
For add the fan you must drill a lot of holes in the case of the flashlight.
Use a pipe cutter and pull the whole system out. Never glue the end cap on where the switch is then make repairs and glue it back together.
Hi Also Watch my channel #diyelectronicandhack
MrBrymstond Yes u r damn correct.
Please subscribe to my channel and I'll sub u back
চমৎকার হইছে
You are the best ceep it up
How many 18650 battery should use for this light
which place you buy the things
Well done..Nicely made.Keep it up!!
What name of glass which use in to make brite
very nice
good work
You from Indonesia? I see many patios that look similar to yours whenever I visit Java Island.
You can do this without a fan blower, just put an adequate heat sink to save some battery
Bardzo fajna latarką nawet bez soczewki robi swoje daję 5+
Офигенное самоделки🤙
how much is the run time of it? i want to.use it as cycle headlight
Nice
Good ideas for transformer pipe PVC in lihgt led we are the champion.
I think I got a problem that will take a Creative mind so I came to the right place.
I balt a MOPAD 2018 model.My head lights on Bright are not enough to see dim setting is more of a joke!
Any ideas that will not cast me a lot I paid 1,300$ for it so I'm out of cash and majer problems driven home from work. Any ideas I would be Much Appreciated!?!?!😀
Great work brother ❤❤❤
Hi guys nice video
Awesome....
frist like
Use,adapter 5volt 1000ma no problem?
nice
How to get the LED?
Really nice video quality. I wonder if you can share the brand of your camera.
His camera is most likely any decent phone attached to a gimbal.
I like ur vids
Why do you need a heat sink and fan?
Where does the hot air go?
I can't find the led. Where did you get it?
Nice.
You are a legend
Hello i can not find the same led chip as you have on the 3.7v one. Can you please help me to find it?
The pipe channel :p
Please give the products link
That 's great .. I like the idea .. keep going ...
Sir wo led lens kaha pe milega
Wow good flashlight bro :D
What model about 20w led? Cree?
Where did you get the lense...
Why you cut of that piece but glue it back on?
He didnt glue it back on he glued it to a different piece to extend it.
Show de bola parabéns
Amazing bro
Y aurait tilleul possibilités de faire une vidéo avec la fabrication d'une belle lampe torche de 100w avec module 12v->35v avec un potentiometre permettant de faire varier la luminosité de la led avec une batterie de 12v rechargeable et 18650 Merci à vous et continuer tout ce que vous faite 😃😃
Mr. I think it has a little LED in its thermal paste
Genial...👍👍👍😀
Music on 04.15 is great...does anyone know who is author?
Bhai yah lens kitne ka hai reply kro
Muito bom. Parabéns!!!