Thank you for making a full explanatory video in English! Before your video I had a very hard time finding any detailed explanations for using and wiring this model!
Your very welcome . I am glad you find useful. The best way to thank me is to subscribe to my channel . It helps me a lot and other people find my videos easily. Thanks
Very useful video! Especially the episode where you show that the device stores setting when the power is off. I could not find that anywhere else. Thank you!
Dear @@robojax, I have installed the device as a humidity controller and I'm having some problems. Maybe you can point me to possible causes. It has been 6 days since it's running. It fires at 75% RH and turns off when reaching 90% RH. Yesterday, I woke up seeing the RH at 106%,. The ligth on the STC-3028 was off and yet, the humidificator attached to it was still on. It seems the relay did not stop the electricity! When I vent the sensor off and I make it reach 75%, it starts again, and reaching 90% it stops and no, it works.. But every once in a while, it fails again... Any thought on what could it be? Factory defect? I'm connected to a 230W socket (this is now Spains voltage) and I wonder if that might be the problem. .
Love the fact that this is in English, as most for this are not and that you're Canadian, as am I and you did a great job explaining this device. So you earned a like and sub from me. But I wish you had showed all of your wiring for every demonstration. That's the most confusing part of this thing for me, not so much the functions, but that's also highly useful and helps me learn the device better. Other videos in other languages showed their wiring, so between theirs and yours it should be fairly straight forward, I think.
Hello you must have skipped the video y. I just opened the video and have saw two sections: sensor wiring and then have shown the actual wiring. Please watch
@@robojax O.k., fair enough. Maybe I missed something. It was late and I was getting tired when I watched it. So admittedly, I may not have been paying good enough attention. I did see you go over wiring, yes, on one device (the lightbulb I believe). But the others, you just showed already hooked up and then proceeded to explain how the functions relate to that device you hooked up. What I meant was, I would have liked to see how every device was wired to the unit, as there are multiple ways to wire and configure this thing. Like the option of powering them all off the same power supply vs. each thing having it's own supply, like the wiring diagram shows can be done. And you did explain that every other device you hook up to it, works similar to how the lightbulb is wired, but I am so green when it comes to electrical and this stuff, I need detailed demonstrations of everything. Yours is still the best video I've seen on functions of it and how to approach wiring it, it was very logical and one of the only few videos in English about it.
Awesome video thanks! So this cannot be used to control both heating and cooling simultaneously, ie turning on/off a heater within a certain range as well as turning on/off an aircon for cooling within a certain temperature range?
hi ive been trying make a terrarium and have been trying to wire a STC-3028 together but on the cooling I want a peltier device with a fan for the temp side and for the humidity side I wanted a humidifier with a fan to circulate in the terrarium I was wondering if this is possible with this device or if you knew of any others
Thank you for a thorough tutorial on an STC-3028. I just bought an STC-3028 from AliExpress under US $7 + Free S/H to US. If you don't mind, I do have a question in wiring this item. In this case, I am using a polarized extension cord to wire my STC-3028. The question I have is whether it is OK to use the (-) line as a pass through and the (+) line as the controlled line to connect to the S1 (temperature) and S2 (humidity) port.
Great video, thanks. Could you advise if we can have leads from both temperature and humidity to a single fan? Not sure if it would back feed and break the unit? Thank you.
we have a resource page for this product robojax.com/learn/arduino/?vid=robojax_Thermostat_SHT2000 and I have added the explanation for HHH and LLL there
ello, great video, yet i still have to understand if it's either cooling or heating and, mostly imoportant if i need a relay or the unit itself acts as a relay? tanks
Hi, you made me watch the video and in the fist 15 seconds I mentioned that “you can use it as heater OR cooler controller “ so I mentioned OR and perhaps 20 or more times. Now the relay is inside it. You just need yo make two wires from your heater or cooler to connect.please watch again as I can assure you that you should not have may questions after carefully watching it.
we can't connect humidifier and dehumidifier simultaneously , or heater and cooler as well ...only 2 devices can be connected , is that true ? is there a version contains 4 controllers ?
Great video, but I dont understand how do you connect a heater and a cooler while you have only one port out? The same for humidifier and dehumidifier? I guess you need 4 devices: 1- heater 2- cooler 3 - Dehumidifier 4 - Humidifier. How do you connect all 4 of them?
W1209 temp controller also has the same microcontroller, So my question is can we swap the w1209 microcontroller without any Programming stuff etc etc in case STC 3028 microcontroller get faulty, The second question about 2nd chip in stc3028 which is shift register is it need any programming or just we can simply replace with new one if get faulty ? Strongly req the questions plz 😢
Hi thank you very much for an excellent video. My stc 3028 works perfectly. only problem I have which is a significant one, is on the RH setting when it reaches 100% it deactivates the RH relay . I can't find or change any settings to prevent this . the controller works absolutely fine on temperature and Rh but if it reaches 100% humidity the controller clicks off the Rh relay . This pretty annoying and I'm unable to solve this. any help would be appreciated. Also there's a setting range not shown in your video for p0 P1 P2 and P3 which are alarm limits and time delays but these do not affect the maximum RH value from cutting off the relay thanks again. Peter
this can turn ON or OFF a load. Air-conditioner or AC is very complex machine and each model has different wiring. so you have to find out when the thermostat of AC detects the temperature what it does so you wire it to do the same thing. most ACs have wiring diagram printed on machine somerehre. Talk to someone who know this and seek help.
When we speak of humidity, it should not be exposed to water. It should be protected but you can keep it outside away from water, like umbrella to keep the rain out.
hi - I love the professional way you explain the operating and electronic of the controller , I face a problem with STC -3028 the humidity switch will start at 62% HR and stop at 72 % - most of the time works - last few days -suddenly it don’t stop at all - my humidor was wet and the blue side of the STC was on 95% HR ... what can i do ? is there a more reliable controller ? Thanks Micky
@@robojax sensors are ok - i have 2 in the hiumidor to compere RH level , when 3028 work OK i here the relay click - when it dosent stop - no realy click ??
Maybe it's because of a false signal induced by the wire of the power supply. When that wire is too close to the wires of the sensor, it may induce a low current through the sensor's wire. Since electronics function with little power, that could be the problem. Prolly a bit late to the party 😂🎉
Very god video. I want to know what is connecting to the humidity wiring..is it the fan?..also please clarify if the lines for the humidity and temperature is 110v/220v. And not Dc voltage ? Much thanks.
Great video and so well structured. Thabk you! What would happen if I connected SHT35 sensor instead of the one that is included? Would it work? I'm looking for better RH accuracy :)
Hello, I am already using the STC 1000 for an incubator. This has a temperature return difference F2 of at least 0.3 C°. This is not exactly ideal for a constant brood temperature. With a brood temperature of e.g. 37.5 C° you have a tolerance of at most 0.2 C° upwards or downwards. How much is the temperature return difference for this model STC 3000 or STC 3028? THANK YOU VERY MUCH
Hello, this item STC3000 s.click.aliexpress.com/e/_DEyUATV shows Accuracy: 0.1Celsius and STC3208 shows Accuracy: ±1°C in here s.click.aliexpress.com/e/_DcI7per
@@robojax The links do not work. You surely mean 3028 and not 3208? If the STC 3028 has a switch-on differential of 1C°, then that is a lot. After all, my STC 1000 has a switch-on difference of 0.3C°. The STC 3000 also has a temperature difference value of 0.3C° at the F2 setting.
phase current is not passing through the humidifier relay ( current in port 6 but not out in 7) thats why my humidifier is not functioning. how can i solve it?
@@robojax sorry for that. My humidifier is written 24v, and on this video you used bulb as the source of humidity. I mean can I used my humidifier and do same connection as you show here.
Can this thing run a fridge? I see it's rated for 10A, but I know refrigerator compressors can take several times their rated current for 0.2-0.5 seconds at startup. Will, say, 12-15A for less than half a second be a problem? If so, could the relays simply be upgraded inside? What is the mode of failure when momentarily overcurrent like this?
I have explained all features and functions. I can't comment on each number as I have to watch the video to answer. So if you watched and did not see the feature, then it can't do it.
Can this turn on refrigeration when temp is above 4C but off at 1.5C but if it goes below 1 it turns on the heater until it again is above 1C. The idea is to stop freezing.
I believe I have demonstrated and also explained the maximum and minimum temperature. Your refrigerator is a load. Just calculate how much power or current it consumes so this relay can handle it.
I am not sure of an already existing product, but you can build your own using Arduino and relay. I have tones of it. just search for "robojax thermostat"
Hi very well made review 👍👌 do you think that if the sensor will be flood in water it will damage the sensor unit? Will it work after drying out? Thanks
Respected sir,I like to see your incubator tutorial - sir one doubt how to calculate heatcalculation(or)how mouch watts used the bulb in incubator(or)heater?
hi sir. I was looking at the manual and it stated there that the measurement temperature range is -20c - +80c. Is it possible for me to use it for my mushroom greenhouse misting system? From what I studied, the best temperature for the mushroom is around 20c. Thank you in advance.
Can you explain me what happened when this device don't stop keep ruining increasing the temperature I follow every step on the wire connections the same way I follow the instructions to program temperature and humidity but seems like temperature never stop and the moisture never increase
You 'd better look further. I just bought the 3008 version. Red channel did not switch (always on regardless status of indicator light). When I tried the blue channel it said SPAT! and the fuse in my distribution cabinet was blown. Yes, I wired correctly. It is dangerous junk.
By chance, do you know of any device that combines temperature control and buck regulator? I'd like to vary an output voltage according to temperature, so I can drive a Peltier module in a smooth way that is more power efficient, rather than switching it abruptly on and off.
very custom need. Possible to have such thing but not see it. You can use Arduino to achieve such thing. I have over 300 videos on Arduino if you want to learn and do it. or hire someone at upwork.com
@@robojax I was hoping there was some way to connect an NTC thermistor in place of the potentiometer of an adjustable regulator... or is that nonsense?
Hello, is it possible to operate the thermostat from 220 to 12v Is this from the transformer or the thermostat? I am from the middle west of Libya and I will translate it on Google
I have just installed one of these, power in is OK, it's on and I can set the temp. "Out" Light comes on so it should have power out to the target appliance, nothing. Temp and humidity are the same.
you need another tool to calibrate it. you can't just do it by entering number. you use a trusted measurement tool, measure and the same liquid or air, then set it to that value.
@@robojax I am done that but i am thinks just to compare with your settings. I know two of them can h+ve different calibration settings but also sometimes can be a same. Thanks
@@robojax Ok thanks i use it for incubator and temerature calibration must be done before you star the trace -> info 4 someone who will read this comment section mine temp calibration is 1.4 See ya folks. BTW Thanks for nice videos Robojax
سوف أرى. أقوم بإطلاق قناة جديدة ستركز فقط على الطاقة والطاقة مثل البطارية والطاقة الشمسية وأجهزة الشحن. في غضون أيام قليلة سترى ذلك. سيكون "WATT HOUR" هو اسم القناة.
Hello, Subscribed!! Can you make a video regarding the fake STC 3028, I bought one recently and it contains the DHT11 temp humidity sensor used on arduino projects used by kids. It would be great help, Thanks
Hello and thank you. Operation of it is the same. you are welcome. Few weeks back I published my Arduino course worth $200 on Udemy. Arduino Step by Step Course (over 100 lectures) Starts here robojax.com/L/?id=338
Please watch each sensor video to see how accurate they are. I don’t remember the numbers. Here is how you can find a video in a UA-cam channel ua-cam.com/video/OhkUceBWcHs/v-deo.html
Hiii..... thanks from India I regular watch your videos And I'm learning lot of things from your videos Its my request to you to please make a proper video on TTGO-T-CALL Module I need your WhatsApp no.
You are welcome. Please subscribe. I appreciate it and helps my channel grow. Thank you. I don't remember what I did in this video. but if this module allowed calibration, I have shown it for sure.
Please subscribe 🛎 and thumb up 👍. Thanks
I will subscribe your Chanel...😊❤
Thank you for making a full explanatory video in English! Before your video I had a very hard time finding any detailed explanations for using and wiring this model!
You are welcome. Please subscribe. I appreciate it and helps my channel grow. Thank you
Another great work Mr Ahmad thanks a lot for your tutorials. Wish you and your family a healthy new year.
you are very welcome. I wish you and your family too a happy and prosperous new year.
I don't usually leave a comment, but this video is really great and informative, so thanks and good job!
Your very welcome . I am glad you find useful. The best way to thank me is to subscribe to my channel . It helps me a lot and other people find my videos easily. Thanks
Very useful video! Especially the episode where you show that the device stores setting when the power is off. I could not find that anywhere else. Thank you!
Thank you so much for your thorough explanation! Natural teacher!
You are very welcome. I am glad you liked it. stay safe. Please don't forget to subscribe. I appreciate it.
Dear @@robojax, I have installed the device as a humidity controller and I'm having some problems. Maybe you can point me to possible causes. It has been 6 days since it's running. It fires at 75% RH and turns off when reaching 90% RH. Yesterday, I woke up seeing the RH at 106%,. The ligth on the STC-3028 was off and yet, the humidificator attached to it was still on. It seems the relay did not stop the electricity!
When I vent the sensor off and I make it reach 75%, it starts again, and reaching 90% it stops and no, it works.. But every once in a while, it fails again... Any thought on what could it be? Factory defect? I'm connected to a 230W socket (this is now Spains voltage) and I wonder if that might be the problem. .
Jestem totalnym laikiem w takich kwestiach, ale dzięki takim filmikom poradziłem sobie bez problemu :) Dziękuję!
Cieszę się, że znalazłeś to przydatne. Pozdrowienia z Kanady. Bądź bezpieczny
the first proper explanation, Thank you
Thank you, very clear explanations. Would you please do a video on calibrating the controller ?
Very informative. U have done a good job!
Glad it was helpful!
Happy New Year Sir, Thanks for all the tutorials throughout the year.
Sorry for I was not able to wish you a Merry Christmas
A belated Merry Christmas
Happy new year!
voice is too low.....neee to upgrade
Love the fact that this is in English, as most for this are not and that you're Canadian, as am I and you did a great job explaining this device. So you earned a like and sub from me. But I wish you had showed all of your wiring for every demonstration. That's the most confusing part of this thing for me, not so much the functions, but that's also highly useful and helps me learn the device better. Other videos in other languages showed their wiring, so between theirs and yours it should be fairly straight forward, I think.
Hello you must have skipped the video y. I just opened the video and have saw two sections: sensor wiring and then have shown the actual wiring. Please watch
@@robojax O.k., fair enough. Maybe I missed something. It was late and I was getting tired when I watched it. So admittedly, I may not have been paying good enough attention. I did see you go over wiring, yes, on one device (the lightbulb I believe). But the others, you just showed already hooked up and then proceeded to explain how the functions relate to that device you hooked up.
What I meant was, I would have liked to see how every device was wired to the unit, as there are multiple ways to wire and configure this thing. Like the option of powering them all off the same power supply vs. each thing having it's own supply, like the wiring diagram shows can be done. And you did explain that every other device you hook up to it, works similar to how the lightbulb is wired, but I am so green when it comes to electrical and this stuff, I need detailed demonstrations of everything. Yours is still the best video I've seen on functions of it and how to approach wiring it, it was very logical and one of the only few videos in English about it.
Thanks yours video very help me to setting temp for cooling. Success for you
Awesome video thanks! So this cannot be used to control both heating and cooling simultaneously, ie turning on/off a heater within a certain range as well as turning on/off an aircon for cooling within a certain temperature range?
Happy new year Ahmad ! :)
Happy new year Co Fa!!
Thank You for speaking in English
hi ive been trying make a terrarium and have been trying to wire a STC-3028 together but on the cooling I want a peltier device with a fan for the temp side and for the humidity side I wanted a humidifier with a fan to circulate in the terrarium I was wondering if this is possible with this device or if you knew of any others
Happy New Year sir.
Greatly explained 🙂
Hi, would it be possible to add wireless to the STC? I need a way to log everything and see data of information remotely. Thanks
No
Very helpful, thank you!
Thank you ,this was a good explanation.
very helpful,thanks
Thank you for a thorough tutorial on an STC-3028.
I just bought an STC-3028 from AliExpress under US $7 + Free S/H to US. If you don't mind, I do have a question in wiring this item. In this case, I am using a polarized extension cord to wire my STC-3028. The question I have is whether it is OK to use the (-) line as a pass through and the (+) line as the controlled line to connect to the S1 (temperature) and S2 (humidity) port.
Thank you so much . Very well explained .
Great video, thanks. Could you advise if we can have leads from both temperature and humidity to a single fan? Not sure if it would back feed and break the unit? Thank you.
Huge thanks mate !
I see a provision for a buzzer on the "Buz1" pins. Is it active or passive?
🌹🌹🌹🌹!!!! Nicely explained.
REALLY good review, appreciate the detail and tips without being too much.
I am glad you liked it. The best appreciation for me is to subscribe to my channel. thank you.
life saver video. thanks a ton.
You are welcome.I am glad it helped
Awesome video
Thank you so much!
Good presentation .....I have a problem with my STC-3028. Sometimes it displays LLL LLL. Is it normal?
we have a resource page for this product robojax.com/learn/arduino/?vid=robojax_Thermostat_SHT2000 and I have added the explanation for HHH and LLL there
ello, great video, yet i still have to understand if it's either cooling or heating and, mostly imoportant if i need a relay or the unit itself acts as a relay? tanks
Hi, you made me watch the video and in the fist 15 seconds I mentioned that “you can use it as heater OR cooler controller “ so I mentioned OR and perhaps 20 or more times. Now the relay is inside it. You just need yo make two wires from your heater or cooler to connect.please watch again as I can assure you that you should not have may questions after carefully watching it.
Thank you!
Good explanation
Good day sir, may I ask if what is the specific value/code number of the switching controller IC in the power supply section? the one with 8 pins?
this is the sensor s.click.aliexpress.com/e/_DFa5reR
we can't connect humidifier and dehumidifier simultaneously , or heater and cooler as well ...only 2 devices can be connected , is that true ? is there a version contains 4 controllers ?
Hi...
Can I use this model (110-220V), but using 12V DC from a solar charge regulator? .
take care, hugs ✌
Great video, but I dont understand how do you connect a heater and a cooler while you have only one port out? The same for humidifier and dehumidifier? I guess you need 4 devices: 1- heater 2- cooler 3 - Dehumidifier 4 - Humidifier. How do you connect all 4 of them?
You can connect two device’s heater or cooler. Not both
Perhaps you may need to watch it again
Many thanks it was very helpful
You are very welcome.
W1209 temp controller also has the same microcontroller,
So my question is can we swap the w1209 microcontroller without any Programming stuff etc etc in case STC 3028 microcontroller get faulty,
The second question about 2nd chip in stc3028 which is shift register is it need any programming or just we can simply replace with new one if get faulty ?
Strongly req the questions plz 😢
Thanks! a very complete video, good machine, you helped me to have new chickens ;)
You are welcome. Please subscribe. I appreciate it and helps my channel grow. Thank you
Excellent tutorial. Thanks
You are welcome. Please subscribe. I appreciate it and helps my channel grow. Thank you
Hi thank you very much for an excellent video.
My stc 3028 works perfectly. only problem I have which is a significant one, is on the RH setting when it reaches 100% it deactivates the RH relay .
I can't find or change any settings to prevent this .
the controller works absolutely fine on temperature and Rh but if it reaches 100% humidity the controller clicks off the Rh relay . This pretty annoying and I'm unable to solve this. any help would be appreciated.
Also there's a setting range not shown in your video for p0 P1 P2 and P3 which are alarm limits and time delays but these do not affect the maximum RH value from cutting off the relay thanks again.
Peter
perfect tutorial..respect
Thank you. Please subscribe. I appreciate it and helps my channel grow. Thank you
Greetings
Thank you so much
Thanks Mate. Happy to see tutorial for my ST3028. It does not come with the manual when i bought it. 😂
No problem 👍
Very interesting and detailed.
How do I link this device with air-conditioner
this can turn ON or OFF a load. Air-conditioner or AC is very complex machine and each model has different wiring. so you have to find out when the thermostat of AC detects the temperature what it does so you wire it to do the same thing. most ACs have wiring diagram printed on machine somerehre. Talk to someone who know this and seek help.
@@robojax thank you so much sir
I want all this for bananas ripening room
Can you please tell me if this sensor can be installed outdoors? Is the sun and rain a hindrance?
When we speak of humidity, it should not be exposed to water. It should be protected but you can keep it outside away from water, like umbrella to keep the rain out.
Great demo. Thanks.
You are welcome. Please subscribe. I appreciate it and helps my channel grow. Thank you
Hi! The wiring cablage for the 12 v is the same? How have I wiring the outputs? Thank so much
yes
Hi thanks for the video, I was a bit confused about the 12 volt relay, does it output DC 12 volts to a load?
Hello, it seems you did not get that it does . Please watch it again.
hi - I love the professional way you explain the operating and electronic of the controller , I face a problem with STC -3028 the humidity switch will start at 62% HR and stop at 72 % - most of the time works - last few days -suddenly it don’t stop at all - my humidor was wet and the blue side of the STC was on 95% HR ... what can i do ? is there a more reliable controller ? Thanks Micky
Hi, I am not sure what has gone wrong. Check the sensors and the wirings. There are more expensive module but I don’t have the model in hand.
@@robojax sensors are ok - i have 2 in the hiumidor to compere RH level , when 3028 work OK i here the relay click - when it dosent stop - no realy click ??
Maybe it's because of a false signal induced by the wire of the power supply. When that wire is too close to the wires of the sensor, it may induce a low current through the sensor's wire. Since electronics function with little power, that could be the problem. Prolly a bit late to the party 😂🎉
Very god video. I want to know what is connecting to the humidity wiring..is it the fan?..also please clarify if the lines for the humidity and temperature is 110v/220v. And not Dc voltage ? Much thanks.
it does not have multiple input. Just one power for both relays.
Great video and so well structured. Thabk you!
What would happen if I connected SHT35 sensor instead of the one that is included? Would it work? I'm looking for better RH accuracy :)
Can it be factory reset as having trouble min. Not turning off heat
I believe I have explained all features. So watch it fully.
If you don’t see it in the video then it does not have that feature
Great Video, had a quick question, can I use both the sensors for heating? I have two heat mats that I would like to regulate the temperature. Thanks
which both sensor? this has only one.
@@robojax I meant both left and right terminal.
One temperature and the other is humidity which you can use bit at the same tumey
very good explanation but tell me how would you control a humidifier and de humidifier from the same circuit it it is two different units
no you can't.
Hello,
I am already using the STC 1000 for an incubator. This has a temperature return difference F2 of at least 0.3 C°. This is not exactly ideal for a constant brood temperature. With a brood temperature of e.g. 37.5 C° you have a tolerance of at most 0.2 C° upwards or downwards. How much is the temperature return difference for this model STC 3000 or STC 3028? THANK YOU VERY MUCH
Hello, this item STC3000 s.click.aliexpress.com/e/_DEyUATV shows Accuracy: 0.1Celsius and STC3208 shows Accuracy: ±1°C in here s.click.aliexpress.com/e/_DcI7per
@@robojax The links do not work.
You surely mean 3028 and not 3208?
If the STC 3028 has a switch-on differential of 1C°, then that is a lot. After all, my STC 1000 has a switch-on difference of 0.3C°.
The STC 3000 also has a temperature difference value of 0.3C° at the F2 setting.
phase current is not passing through the humidifier relay ( current in port 6 but not out in 7) thats why my humidifier is not functioning. how can i solve it?
I m using. 24v humidifier can I connect it direct and bridge it as you show using the bulb thanks
? Confusing.
@@robojax sorry for that. My humidifier is written 24v, and on this video you used bulb as the source of humidity. I mean can I used my humidifier and do same connection as you show here.
Can this thing run a fridge? I see it's rated for 10A, but I know refrigerator compressors can take several times their rated current for 0.2-0.5 seconds at startup. Will, say, 12-15A for less than half a second be a problem? If so, could the relays simply be upgraded inside? What is the mode of failure when momentarily overcurrent like this?
I am not sure bout the handling higher current for few seconds. check with the manufacturer of relay. or yes. upgrade it.
thank u sir
Can you actually set this unit as:
When Humidity reach:25rh
then Heater switch on until 65c?
Is this possible?
I have explained all features and functions. I can't comment on each number as I have to watch the video to answer. So if you watched and did not see the feature, then it can't do it.
Can this turn on refrigeration when temp is above 4C but off at 1.5C but if it goes below 1 it turns on the heater until it again is above 1C. The idea is to stop freezing.
I believe I have demonstrated and also explained the maximum and minimum temperature. Your refrigerator is a load. Just calculate how much power or current it consumes so this relay can handle it.
Once unplugged, does it save the settings? Any link to an english pdf manual?
Yes. I believe I mentioned it in video. This is the manual. I made this video because there was not manual.
any suggestion for better accuracy products. I need better than 1 degre celcius.
I am not sure of an already existing product, but you can build your own using Arduino and relay. I have tones of it. just search for "robojax thermostat"
Hi very well made review 👍👌 do you think that if the sensor will be flood in water it will damage the sensor unit? Will it work after drying out? Thanks
I have shown the sensor name and model. check the datasheet for the sensor. I don't know if it survives flood or not.
Yeah it says 100% humidity... But the hardware, electrical connection and so on ? They will jump and oxydate no?
Respected sir,I like to see your incubator tutorial - sir one doubt how to calculate heatcalculation(or)how mouch watts used the bulb in incubator(or)heater?
hi sir. I was looking at the manual and it stated there that the measurement temperature range is -20c - +80c. Is it possible for me to use it for my mushroom greenhouse misting system? From what I studied, the best temperature for the mushroom is around 20c. Thank you in advance.
Hello, I have no knowledge of growing mushroom . Try Bing or google search.
left a masage 3 days ago - can you help ?
I have replied that best I could say.
Can you explain me what happened when this device don't stop keep ruining increasing the temperature I follow every step on the wire connections the same way I follow the instructions to program temperature and humidity but seems like temperature never stop and the moisture never increase
With wiring is incorrect or your device or sensor is bad.
How do you start that damn thing? Every time i plug it in it shows 888 888. It remembers the set values but doesnt read actual ones.
I believe I mentioned what 888 means. It should just start if there is no problem.
Or check the link in the description.
You 'd better look further. I just bought the 3008 version. Red channel did not switch (always on regardless status of indicator light). When I tried the blue channel it said SPAT! and the fuse in my distribution cabinet was blown.
Yes, I wired correctly. It is dangerous junk.
Assalamu alaikum, can u please suggest me a good Temperature & Humidity Controller for Home made egg incubator? Please..
I have no idea about incubator. Do a Bing or google search and learn about eggs and temperature need to incubate then use this device
By chance, do you know of any device that combines temperature control and buck regulator? I'd like to vary an output voltage according to temperature, so I can drive a Peltier module in a smooth way that is more power efficient, rather than switching it abruptly on and off.
very custom need. Possible to have such thing but not see it. You can use Arduino to achieve such thing. I have over 300 videos on Arduino if you want to learn and do it. or hire someone at upwork.com
@@robojax I was hoping there was some way to connect an NTC thermistor in place of the potentiometer of an adjustable regulator... or is that nonsense?
Sory i subscribed and 2 times thumb up!!
NICE...how about CALIBRATION?
I have completed everything. If it had that feature I would have explained it
@@robojax THANKS SIR, is there a way to calibrate my stc3028?
Hello, is it possible to operate the thermostat from 220 to 12v Is this from the transformer or the thermostat? I am from the middle west of Libya and I will translate it on Google
There are two versions. Ac and CD and use whichever you prefer.
i My stc 3028 shows 888 on both displays
what do i have to do?
It means sensor is not connected
Hello Sir
I want the ESP8266 and ESP32 tutorials to return. Please try to make more videos for them.
Hello, more to come.
How to know that temperature of stc 3028 is accurate and how to correct it?
if this module has option to compensate, I should have shown it as I never leave details. So it should be in the video .
I have just installed one of these, power in is OK, it's on and I can set the temp.
"Out" Light comes on so it should have power out to the target appliance, nothing.
Temp and humidity are the same.
Can you give me exact numbesr for calibration temperature and humidity?
you need another tool to calibrate it. you can't just do it by entering number. you use a trusted measurement tool, measure and the same liquid or air, then set it to that value.
@@robojax I am done that but i am thinks just to compare with your settings. I know two of them can h+ve different calibration settings but also sometimes can be a same. Thanks
I have not changed it, whatever it shows I accord it and used only once to make video.
@@robojax Ok thanks i use it for incubator and temerature calibration must be done before you star the trace -> info 4 someone who will read this comment section mine temp calibration is 1.4
See ya folks.
BTW
Thanks for nice videos Robojax
How to re start that?
What did show then? y ou power it up and it will turn on. then set the values to make it work.
حبيبي يا احمد باشا ممكن شرح تحويل المولد الى متور وشكرا
سوف أرى. أقوم بإطلاق قناة جديدة ستركز فقط على الطاقة والطاقة مثل البطارية والطاقة الشمسية وأجهزة الشحن. في غضون أيام قليلة سترى ذلك. سيكون "WATT HOUR" هو اسم القناة.
Hello, Subscribed!!
Can you make a video regarding the fake STC 3028,
I bought one recently and it contains the DHT11 temp humidity sensor used on arduino projects used by kids. It would be great help, Thanks
Hello and thank you. Operation of it is the same. you are welcome. Few weeks back I published my Arduino course worth $200 on Udemy. Arduino Step by Step Course (over 100 lectures) Starts here robojax.com/L/?id=338
@@robojax , Hi, Is their durability and accuracy the same?
Please watch each sensor video to see how accurate they are. I don’t remember the numbers. Here is how you can find a video in a UA-cam channel ua-cam.com/video/OhkUceBWcHs/v-deo.html
👍👍
No body knows the 12v or 24v positive and negative conditions which is which
✔✔🧿✔✔
Hiii..... thanks from India
I regular watch your videos
And I'm learning lot of things from your videos
Its my request to you to please make a proper video on TTGO-T-CALL Module
I need your WhatsApp no.
thanks Shubham, I will try to get The TTGO. Other than replying to comments on UA-cam, I have no time to reply.
@@robojax send me your WhatsApp no. Please
Other than replying to comments on UA-cam, I have no time to reply.
First
Thank you, very clear explanations. Would you please do a video on calibrating the controller ?
You are welcome. Please subscribe. I appreciate it and helps my channel grow. Thank you. I don't remember what I did in this video. but if this module allowed calibration, I have shown it for sure.