@Ebikes Repair I recently bought a replacement battery for my mantis Is there a specific way the battery is connected to the controller ? Or it doesn’t matter which battery cable you connect to controller? I don’t want to short the battery or controller 😢
I think it doesn't matter. Which connector goes to which controller - verify polarity with a multimeter first. Be careful though as I had a bad controller and connected the battery and the xt60 disintegrated all over my hands and burned me!
I just replaced my controller, all works well. but i am now having trouble placing the controller inside the compartment to line up the screws. Its like the new wiring is stiff af and doesnt allow room for the controller to be seated properly inside. All wires are thru hole and squashed up next to battery. Any advice?
Hi there, I've got a mantis 10 pro and I'm seeing many different ones for sale. Which one(controller) would I need? I see different specs 60v 27A or 60v 30A etc..
hi,can you help??? i have a kaboo mantis 10 single motor and i have a no acceleration no motor spin issue, lights work, battery is fully charged, no error codes can you help??? Thanks in advance
Hi i have 1 off these scooters. It charges perfect. Turns on runs then knocks off till plugged back into charge. Same cycle again .. any ideas on problem
Do you mind explaining better the conections? Like what is what and the function they have? You are the only video that exists at the moment id really appreciate it
I just put a new controller on this and it doesn't run but turns on. Is there a safety switch to have this running. I dont want to put it all back if theres something wrong
I really need help wiring my mantis 10 with a new controller. Any possibility I can get a pic of wires that needs to connect? If it takes time to do that I can PayPal you what is the cost to to that. Thank you
can you tell me why my mantis 10 pro with minimotors controller same like this have more torque in eco mode than in turbo 3rd gear mine is with flashlight version 4
@@EbikeRepairs yes in turbo the speed increases i had a problem with the front motor going half power the seller made something with the controller and didn't want to tell me what was the problem but from then i miss the torque which i had now its gone
@@EbikeRepairs in eco there is slight delay in acceleration when i hit the throttle and torque kicks in note that it was other way turbo mode had a beast torque and eco not that much torque now is opposite
Is it the same for the Mantis 10 pro? :) my back motor stopped working showing e10 on the display and i should be the controller to the display there is a problem
@@EbikeRepairs ok thank you so much. do u have an idea how i can connect all the cables if i only have 1 new controller, and not 3 controllers like you? is there some image with wire color connection? best regards
@@EbikeRepairs yes mate when I held the power button on my old screen it made a little noise , I’ve replaced the screen and it works spot on now . Must have shortened out somewhere and blew my screen 👍 thanks for your help anyhow
Is it normal to replace those controllers so often? My scooter is 1 year old and im just about to buy my 3rd controller for replacement
Honestly - the sightest bit of water and they will die. It's quite disappointing,
@Ebikes Repair I recently bought a replacement battery for my mantis
Is there a specific way the battery is connected to the controller ?
Or it doesn’t matter which battery cable you connect to controller?
I don’t want to short the battery or controller 😢
I think it doesn't matter. Which connector goes to which controller - verify polarity with a multimeter first.
Be careful though as I had a bad controller and connected the battery and the xt60 disintegrated all over my hands and burned me!
@@EbikeRepairs I also bought a new controller , I Really hope it goes smoothly for me Thank You !! My Friend!
I just replaced my controller, all works well. but i am now having trouble placing the controller inside the compartment to line up the screws. Its like the new wiring is stiff af and doesnt allow room for the controller to be seated properly inside. All wires are thru hole and squashed up next to battery. Any advice?
I agree, it was a nightmare. I had to put the light wires down the sides of the frame holes where they go, but further in, if that makes sense.
Hi im looking for controllers but they are £100+ where did you get yours as it seems to be aftermarket thanks :)
This one was £140 I think, direct from minimotors store (or whatever it was called) on elixpress 🤞
@@EbikeRepairsthank you 👌🙏
I have a mantis 10, when I spin the wheels and pull the throttle the wheels stop abruptly, any advice?
Sounds like a controller issue, sadly... You could try disconnecting the brake cutoffs though.
Hi there, I've got a mantis 10 pro and I'm seeing many different ones for sale. Which one(controller) would I need? I see different specs 60v 27A or 60v 30A etc..
Very sorry but I'm not sure - you'd need to check the label on your existing controller, if possible. Thanks
Hey can you help me with my Mantis 10? I have a 02 sensor issue but no mechanical experience or tools
Sorry I'm not really the expert on that, but error code lists online might help 👍
hi,can you help??? i have a kaboo mantis 10 single motor and i have a no acceleration no motor spin issue, lights work, battery is fully charged, no error codes can you help??? Thanks in advance
Unplug brake connectors first, if that doesn't work then unfortunately you're probably going to be replacing your controller
Hi i have 1 off these scooters. It charges perfect. Turns on runs then knocks off till plugged back into charge. Same cycle again .. any ideas on problem
Sounds like a bad cells group in the battery pack
Do you mind explaining better the conections? Like what is what and the function they have?
You are the only video that exists at the moment id really appreciate it
Sorry I don't know anymore this was a really long time ago now, I'll have to wait until I get another in!
I just put a new controller on this and it doesn't run but turns on. Is there a safety switch to have this running. I dont want to put it all back if theres something wrong
possibly e brake cutoffs?
I really need help wiring my mantis 10 with a new controller. Any possibility I can get a pic of wires that needs to connect? If it takes time to do that I can PayPal you what is the cost to to that. Thank you
sorry, I don't have one in stock at the moment - but I did describe it all in the video and you should be able to see :)
@@EbikeRepairs thank you
can you tell me why my mantis 10 pro with minimotors controller same like this have more torque in eco mode than in turbo 3rd gear mine is with flashlight version 4
In turbo does the speed increase? Maybe eco and turbo are round the wrong way
@@EbikeRepairs yes in turbo the speed increases i had a problem with the front motor going half power the seller made something with the controller and didn't want to tell me what was the problem but from then i miss the torque which i had now its gone
@@EbikeRepairs in eco there is slight delay in acceleration when i hit the throttle and torque kicks in note that it was other way turbo mode had a beast torque and eco not that much torque now is opposite
Sounds like a bad controller - worth swapping for another they can be had for about £140 if you are happy to wait for shipping
Any ideas if I can change to better control minimotors sick replacing 3rd time now
sorry, im not sure!
cant you waterproof it? with silicone and plastic bag maybe?
I think that will just trap water, sorry
Is it the same for the Mantis 10 pro? :) my back motor stopped working showing e10 on the display and i should be the controller to the display there is a problem
Sorry I'm not sure!
Same problem did you get it to work?
Thank you so much ! realy helpful
My pleasure to help!
which of the controller cables to battery i have to connect first? or does it not matter which cable first and which one connected?
doesnt matter :)
@@EbikeRepairs ok thank you so much. do u have an idea how i can connect all the cables if i only have 1 new controller, and not 3 controllers like you? is there some image with wire color connection? best regards
I have described it all in the video, colours and all - should have everything you need there buddy. thanks!
@@EbikeRepairs thx bro
Is it one controller for both motors? I thought there are two controllers, one for each motor.
There are two flavours I believe, one with two separate controllers - and one with the dual controller built into a single housing.
When you plug the controller to red and black main wires do they pop ? Make a bang noise ?
Yes they do the inrush current to the capacitors can cause a pop/spark.
@@EbikeRepairs okay thought blew them haha , think my screen has broken now cos not turning on. Just making weird screeching sound , shall I replace ?
the screen is screeching?
@@EbikeRepairs yes mate when I held the power button on my old screen it made a little noise , I’ve replaced the screen and it works spot on now .
Must have shortened out somewhere and blew my screen 👍 thanks for your help anyhow
glad its sorted for you bud :)
How can water get into the mantis
Quite easily! the front controller panel appears ti be not sealed at all - neither is the controller itself.
Lucky you don’t blow your fingers off with all the rings and crap on your fingers
Kaboom! Fingies go bye bye
why didint you just replace mosfets cheaper
@@bitsnbobs1969 I need to guarantee it will work - might not have been MOSFETs 👍