I did what you suggested, but after the toner level went below 30% for two colors. As you have said the counters didn't go to nill. Do you think they will reset when I buy and install two original toners? Your second video including programmer is not for me. Now I'm a bit worried about whether the printer will recognize the new toners.
@99spinz 2. If you press the "orange triangle in a circle" button the green led will blink, keep it pressed and it will start to blink faster. Now release the button and voila; a Configuration Report. (if you don't press it long enough (the green led is still blinking slow) you'll get a regular demo page for this printer)
If you still need the drum reset, you can go to Amazon and search for "samsung drum reset chip". No soldering required. Just peel and stick the chip and that is all to reset your drum counter. If you are familiar with soldering, you may buy a drum reset fuse. They are all available from Amazon and eBay.com, eBay.co.uk, amazon.com, amazon.ca, amazon,fr, amazon,es, amazon.de, amazon,it, amazon.co.uk.
I started with the first set of toners (without the chip) "Yellow 63%, Magenta 63%, Cyan 63%, Black 11%". I know the black is very well below 30% but I decided to try it anyway. I turned on the printer, report gives 463 pages printed, I print some pages and print another report, 465 pages. I turn off the printer and turn it back on: report says 463 (mono) pages printed. My guess is that any job that would require more than 11% black can not be printed anymore in one session without reboot.
@99spinz 1. As far as I can tell this hack disables writing to the chip but the chip will still be able to count. This means that if you have 1% left in the toner which is enough for let's say 30 pages the printer will stop working after printing 30 pages because it thinks it's out of toner. You can turn powercycle the printer and it will think again you will have 1% toner left and your facing the same issue after 30 pages. 30% is a safety limit because most print jobs can be done within 30%
@acer6530 cause this firmware most probably freezes that number and it would be non-sense to save it at a number where you are allways warned etc. So just make the printer think, it's full instead of almost empty.
Yellow Status Ready Remain Toner (64%) Magenta Status Ready Remain Toner (76%) Cyan Status Ready Remain Toner (76%) Black Status Ready Remain Toner (43%) what would happen if i do this with my current Supplies Status
Firmware fix DOES NOT RESET EVERYTHING, only the toner values. Instead do a hardware fix which is a bit more difficult but ABSOLUTELY FREE. It's explained here: watch?v=077GLsEMV2E
![Lp. Сердце Вселенной #60 РОЖДЕНИЕ ЛОЛОЛОШКИ [Финал] • Майнкрафт](http://i.ytimg.com/vi/YoR0pAV9FVQ/mqdefault.jpg)
I did what you suggested, but after the toner level went below 30% for two colors. As you have said the counters didn't go to nill. Do you think they will reset when I buy and install two original toners? Your second video including programmer is not for me. Now I'm a bit worried about whether the printer will recognize the new toners.
@metonol my CLP 310 Yellow toner is empty . how i can refill ? whether after refilling , my printer will work properly ?
@homonymsarehere I don't think so, those printers will have a newer firmware with some different features.
does this works with cpl 350n?
does this reset the imaging unit counter?
I do have a CLP-365W. Can I use this method to reset?
what about when the yellow toner is 0% can I still reset it.. can't it still work? please I need ur reply urgently
@redcode5 what is the exact model, and firmware by you printer
when i finish this thing how must be the toner level and the page counter from the test sheet? sorry for my bad english
does this work with clp-315?? thanks
Who sings the last song????
can i demage the printer with this metod ????
good video....
but i have 1 quetion...why must be up to 30% on toner?
@99spinz
2. If you press the "orange triangle in a circle" button the green led will blink, keep it pressed and it will start to blink faster. Now release the button and voila; a Configuration Report. (if you don't press it long enough (the green led is still blinking slow) you'll get a regular demo page for this printer)
my friend....do you have the metod via serial number?
@vukotici32
all is well! having such a status of toner you can do firmware
what about samsung clp-320
If you still need the drum reset, you can go to Amazon and search for "samsung drum reset chip". No soldering required. Just peel and stick the chip and that is all to reset your drum counter. If you are familiar with soldering, you may buy a drum reset fuse. They are all available from Amazon and eBay.com, eBay.co.uk, amazon.com, amazon.ca, amazon,fr, amazon,es, amazon.de, amazon,it, amazon.co.uk.
This discharge is suitable for Samsung 310,315, SAMSUNG CLX-3170/3175
all the luck =)
I started with the first set of toners (without the chip) "Yellow 63%, Magenta 63%, Cyan 63%, Black 11%". I know the black is very well below 30% but I decided to try it anyway.
I turned on the printer, report gives 463 pages printed, I print some pages and print another report, 465 pages. I turn off the printer and turn it back on: report says 463 (mono) pages printed.
My guess is that any job that would require more than 11% black can not be printed anymore in one session without reboot.
@Herakleian42
printer recognize the new toner!
chip seal on a new cartridge
thank you
it works like a charm
respect
@metonol
today i printing some pages and the toner level is going down my os version 1.29.11.08
Tengo una Samsung clp-365w, y me dice que debo colocar una unidad de imágen nueva porque se ha agotado.... ¿Enviame un tutorial al respecto por favor?
@99spinz
1. As far as I can tell this hack disables writing to the chip but the chip will still be able to count. This means that if you have 1% left in the toner which is enough for let's say 30 pages the printer will stop working after printing 30 pages because it thinks it's out of toner. You can turn powercycle the printer and it will think again you will have 1% toner left and your facing the same issue after 30 pages. 30% is a safety limit because most print jobs can be done within 30%
@acer6530 cause this firmware most probably freezes that number and it would be non-sense to save it at a number where you are allways warned etc. So just make the printer think, it's full instead of almost empty.
anyone tested this tecnique on clx-3175?
qual e a senha do arquivo
Yellow Status Ready
Remain Toner (64%)
Magenta Status Ready
Remain Toner (76%)
Cyan Status Ready
Remain Toner (76%)
Black Status Ready
Remain Toner (43%)
what would happen if i do this with my current Supplies Status
@99spinz
the answer to your question
in lesson № 2
work this metod for the model CLP-310N manufactured february 2010 with firmware:v4.01.06 (clp 310) 01-23-2009
is working tnx for tutorial
@tryplex92
hang the counter on the data that were
@356357289
Музыка из игры RED ALERT 2
Firmware fix DOES NOT RESET EVERYTHING, only the toner values. Instead do a hardware fix which is a bit more difficult but ABSOLUTELY FREE. It's explained here: watch?v=077GLsEMV2E