Between 9:30 and 10:15 is THE BEST explanation of drag link geometry there is, THANK YOU for this video and your expertise and your ability to explain the science behind a jeep front end. So many videos fall short or give incorrect and incomplete information. YOU SAID IT BEST, I've learned more in this video than countless hours of other videos. THANK YOU!!!
I'm chasing a poor drive ability issue...your explanation of the relationship between the spindle ball joint and the track bar mount may just be the issue I'm confronting. Thanks for "steering" me in the right direction!
Great video and explanation. I just had 1tons and 40's put on my jku. Rides fantastic on and off the trail. Now planning my next big item, more horsepower. Thanks for sharing.
Very helpful thank you. Been having problems with wobble and so far have replaced everything (some things twice) and just pressed on teraflex ball joints as a last ditch effort. If it doesn’t help I’m worried if using the tape measure to adjust my track bar wasn’t precise enough. But in the end it seemed like there were only two options at 180 degrees putting it about 1/8”off in one direction or 1/4” off the other direction
thanks to explanation,naw i know wat is wrong mounted on my jeep.. the trak bar cu drag link is not parallel.I just monted a Synergy Jeep JK Steering Kit on my jeep with in flip mode with no correction on trak bar. All my car have a big problem ..direction is not ok. I MUST ORDER A RELOCATION BRACKET too corect this..thanks
I have a 15 jku lifted 3.5" rock krawler on 37" after going through Rubicon trail, the jeep doesn't seem right when driving through turns going 30 to 60 MPH. It wonders and I need to constantly correct steering. Also on turns on does a quick slip and catches itself. if anyone has had a similar issue I would love to hear about it. Thanks
He never stated what engine the numbers came from, he was just talking in general about going from one horsepower number to another and what issues can happen.
Excellent video. Someone added a track bar relocation bracket on my 2010 I just purchased, but did not flip the drag link so I believe this is my issue. Question: would you rather have an adjustable track bar and use the factor bolt location for the track bar or leave it in the relocation bracket and install a high steer flip drag link? I have an unlimited with 35's and 4" lift. Jeep drives pretty good on the highway at 70, but in town handling is absolutely deadly. Also, my caster is 3.6 on the passenger and 4.4 on the driver (just had it on the alignment machine). We did not touch it because I have adjustable upper and lower control arms coming for the front (currently has fixed length stock upper and aftermarket lower).
I installed teraflex draglink and tierod in my JK now my steering is off and I can’t center it thru the sleeve on the draglink cuz the sleeve is at max in I can’t make the draglink shorter. What do u think i should look for at this point?
Thanks. What happen when you have doble u-joint driveshaft, since the geometry, that meet to point flat from the differential, If you move the caster the drive shaft angle is going to getting worst. This does not have any solutions?
Great run through, but you mention talking about camber, but I think you may have missed it. I’m having issues with a ton of negative camber and looking for advice on how to correct it.
I assume torque steer is same as bump steer? Thank you for the discussion of this - I always wondered what this meant. Also, I had to abandon one Jeep (a 2010 JK, now own 2016 JK) as I could never resolve death wobble - maybe it was bad caster all along? How prone to DW are the JKs you build?
Between 9:30 and 10:15 is THE BEST explanation of drag link geometry there is, THANK YOU for this video and your expertise and your ability to explain the science behind a jeep front end. So many videos fall short or give incorrect and incomplete information. YOU SAID IT BEST, I've learned more in this video than countless hours of other videos. THANK YOU!!!
ive been struggling figuring mine out. these diagrams helped me undertand where i was going wrong . thank you.. 9:30-10:15 helped me too
The best Explanation ever !!! Thank you !
I'm chasing a poor drive ability issue...your explanation of the relationship between the spindle ball joint and the track bar mount may just be the issue I'm confronting. Thanks for "steering" me in the right direction!
Great video and explanation. I just had 1tons and 40's put on my jku. Rides fantastic on and off the trail. Now planning my next big item, more horsepower. Thanks for sharing.
Ñ
Great info. Just got my first Jeep (2015JK). This has helped me educate my decision for a lift kit. Thanks!
Excellent video on the topic. Thanks for the graphics. They really helped understand the complexities os the suspension.
Very helpful thank you. Been having problems with wobble and so far have replaced everything (some things twice) and just pressed on teraflex ball joints as a last ditch effort. If it doesn’t help I’m worried if using the tape measure to adjust my track bar wasn’t precise enough. But in the end it seemed like there were only two options at 180 degrees putting it about 1/8”off in one direction or 1/4” off the other direction
Toward the end of the video i just realized you're useing a wand to point stuff out lol
Love the Elder Wand ;)
Dumbledore's cooler younger brother. lol
lol the wand pointer is the icing on the cake! good explanation!
Man that a lot of great information! Great job explaining it. Thanks!
Good explanations, A lot of PENTASTARS
I'm brand new to Jeeps, and this video went WAY over my head. Is there a better "basics" video for a Jeep-n00b like me?
No shit!! Mind blown...lol!! Also...not everyone can afford a setup like that either. Very informative though.
This video helps. Thank you!
Great video thanks!
Very nice explanation. Thank you.
Those lower control arms are on upside down. Tire has been contacting it as well.
Excellent
Great Video!! Lot's of great info on it.
I just learned something. Cool
thanks to explanation,naw i know wat is wrong mounted on my jeep.. the trak bar cu drag link is not parallel.I just monted a Synergy Jeep JK Steering Kit on my jeep with in flip mode with no correction on trak bar. All my car have a big problem ..direction is not ok. I MUST ORDER A RELOCATION BRACKET too corect this..thanks
Is that dumbledore’s wand?
Robbie... Just for my FYI... Is there a reason you mounted your lower Control Arms with the Adjusting Nuts on the Axle side 🤔
CastEr*
Super helpful
Love it thanks .
What kind of trackbar is that
I have a 15 jku lifted 3.5" rock krawler on 37" after going through Rubicon trail, the jeep doesn't seem right when driving through turns going 30 to 60 MPH. It wonders and I need to constantly correct steering. Also on turns on does a quick slip and catches itself. if anyone has had a similar issue I would love to hear about it. Thanks
Do you have a track bar bracket? If so toss it and get a new track bar.
I've been through the Rubicon, no issues at all, but you're having issues, get the alignment checked.
200hp? They are almost 300hp unless you're referring to the 3.8
He never stated what engine the numbers came from, he was just talking in general about going from one horsepower number to another and what issues can happen.
im making my way through all of these videos. so good robbie great stuff
Excellent video. Someone added a track bar relocation bracket on my 2010 I just purchased, but did not flip the drag link so I believe this is my issue. Question: would you rather have an adjustable track bar and use the factor bolt location for the track bar or leave it in the relocation bracket and install a high steer flip drag link? I have an unlimited with 35's and 4" lift. Jeep drives pretty good on the highway at 70, but in town handling is absolutely deadly. Also, my caster is 3.6 on the passenger and 4.4 on the driver (just had it on the alignment machine). We did not touch it because I have adjustable upper and lower control arms coming for the front (currently has fixed length stock upper and aftermarket lower).
I installed teraflex draglink and tierod in my JK now my steering is off and I can’t center it thru the sleeve on the draglink cuz the sleeve is at max in I can’t make the draglink shorter. What do u think i should look for at this point?
Lower arms are in backwards and you can see where tires are rubbing on the arms at full lock because the clearance bend is in the wrong place
@WranglerJKLS
Thanks. What happen when you have doble u-joint driveshaft, since the geometry, that meet to point flat from the differential, If you move the caster the drive shaft angle is going to getting worst. This does not have any solutions?
EXCELLENT VIDEO, SAVING THIS FOR REFERENCE!
Great run through, but you mention talking about camber, but I think you may have missed it. I’m having issues with a ton of negative camber and looking for advice on how to correct it.
Great video! @9:50 is the best explanation of bump steer I've ever heard.
Outstanding job... thank you!! 👍🏻🇺🇸
Who makes the track bar and tie rod? Thanks in advance.
Great video, always learning from you Robbie.
I assume torque steer is same as bump steer? Thank you for the discussion of this - I always wondered what this meant. Also, I had to abandon one Jeep (a 2010 JK, now own 2016 JK) as I could never resolve death wobble - maybe it was bad caster all along? How prone to DW are the JKs you build?
DW is tough, it's more art then science to fix in some cases. I will try and get some info up regarding DW.
Good one Robbie. Thanks for doing this.