बहुत अच्छे हाइड्रोलिक के बारे में लीवर के बारे में अच्छी जानकारी प्राप्त हुई हमें धन्यवाद भैया चलो लीवर के बारे में कुछ तो पता चला पहले अनजान थे स्लो फास्ट के बारे में
Abdul JI can you do some repairs videos on Universal tractor{Fiat} 550&640 hydraulic setting & clutch ,brake job or engine service. love the way you teach thx
Abdul Bhai aapka kam bahothi acha he aor aapka samjane ka tarika bhi bahot hi accha he aasani se samaj me aajata he aesehi video ham kisano ke liye banate rahna ise hame kafi sahai milti he aapka dhanyvad abdul khai👌🏽👌🏽👍
Sir mere pas swraj 735 fe 1998 modal ka he isme hidrolik ka red vale che kaltivetr uthta ni he or bleak che 5 inch hi uthta he or chalu me thi dire dire utar jata he sir to hidrolik me kya vajja hogi sir ??
Setting Lever Springs For MF35 Hydraulics Making the settings on the lever springs for the Massey Ferguson 35 hydraulic system is quite a fiddly job, and the method is shown in detail with a written description of the process may also help. The spring balance should be attached at the very end of the levers So here it is... • Loosen retainer nut and eccentric cam. • Make sure quadrant levers are set at their sector marks. The round lever exactly over where it says ‘FAST’, the square lever next to where it says ‘DRAFT’ between the two dots and exactly where the arrow is. • Make sure the lift arms are in the fully lowered position. (that is upwards if the top cover is flipped upside down).       • Make sure your spring balance is connected right at the top of the lever (if it is connected lower down the lever it will require more force to move the lever). • When 3 lb. of pressure is applied it should only just spring it into contact with the front of the slot in the lever support bracket. • Obviously adjustment of the spring pressure is made with the self-locking nut on the guide rods. After this adjustment is made the eccentric cam can be moved around into firm contact with the cam arm and the nut tightened. The above adjustments can be checked - move the operational lever from its sector marks into the response range, as the lever leaves the ‘FAST’ position the levers that we set with the spring balance should begin to move to the rear of the guides. The adjustment is very fine and fiddly. It is often right at the end of the movement of the levers where the 3 lb. can be achieved. The setting is 3 lb. (1361 grams) of force to move the lever. The reason for this is that this equals the force applied by the control valve spring when the assembly is fitted and connected in the tractor. It is a very difficult setting to make and when using a spring balance the 3 lb. setting cannot ever be particularly accurate. Another method would be to attach a piece of string to the lever and pass this over a roller with a 3lb weight hanging off the bottom of the piece of string.
भाई साहब नमस्कार, क्या आप छत्तीसगढ़ वालों को सर्विस दे सकते हो क्या। मुझे अपने ट्रेक्टर पे काम करवाना है।ईंजन, हाइड्रोलिक,स्टेरिंग पे। कृपया बताएं धन्यवाद 🙏🙏🙏
Sir ap dono liver ki position ki kaha rakhar kar setting karte he vo batana Vese to mene ye vala liver setting ka vidieo 2 bara dekha magar ise muje liver ko kaha rakh kar set kaete he ye pata nahi chalata
Setting Lever Springs For MF35 Hydraulics Making the settings on the lever springs for the Massey Ferguson 35 hydraulic system is quite a fiddly job, and the method is shown in detail with a written description of the process may also help. The spring balance should be attached at the very end of the levers So here it is... • Loosen retainer nut and eccentric cam. • Make sure quadrant levers are set at their sector marks. The round lever exactly over where it says ‘FAST’, the square lever next to where it says ‘DRAFT’ between the two dots and exactly where the arrow is. • Make sure the lift arms are in the fully lowered position. (that is upwards if the top cover is flipped upside down).       • Make sure your spring balance is connected right at the top of the lever (if it is connected lower down the lever it will require more force to move the lever). • When 3 lb. of pressure is applied it should only just spring it into contact with the front of the slot in the lever support bracket. • Obviously adjustment of the spring pressure is made with the self-locking nut on the guide rods. After this adjustment is made the eccentric cam can be moved around into firm contact with the cam arm and the nut tightened. The above adjustments can be checked - move the operational lever from its sector marks into the response range, as the lever leaves the ‘FAST’ position the levers that we set with the spring balance should begin to move to the rear of the guides. The adjustment is very fine and fiddly. It is often right at the end of the movement of the levers where the 3 lb. can be achieved. The setting is 3 lb. (1361 grams) of force to move the lever. The reason for this is that this equals the force applied by the control valve spring when the assembly is fitted and connected in the tractor. It is a very difficult setting to make and when using a spring balance the 3 lb. setting cannot ever be particularly accurate. Another method would be to attach a piece of string to the lever and pass this over a roller with a 3lb weight hanging off the bottom of the piece of string.
उस्ताद जी इस विडियो में तो बहुत ही अच्छी जानकारी दी है आपने
बहुत बहुत धन्यवाद सर जी आपका 🇮🇳👍🤝😊
a.b.kured.bahi.tera.samjaneka.tarika.bohat.acchahi.jajakallh.qahyr
आभारी हूँ. आप बहुत अच्छा काम करते है.नमस्कार. शुभ रात्र
आप इतने अच्छे से विडियो के माध्यम से किसानों मदद करते हैं आपक कोटी कोटी धन्यवाद
You welcome Sir thanks 👍🇮🇳
Khub khub dhanyvad bhai Kishan mate video banavva bdl aabhar sarji bahut acha he video
Khub khub aabhar saheb ji dhanyvad 🇮🇳👍
सर जी आपका यह विडियो हमारे को पसन्द आया ऐसे विडियो दिखाते रहे मै आपका सह्रदय सवागत करता हु कल्याण सिह चौहान
Thank Sir Ji 🇮🇳👍🤝😊
Hello sir main aapka bahut bada fan hun sar aap jis tarah samjhate Hain Na koi bhi koi bhi Insan achcha se samjhe jaega
Thanks sir ji 🇮🇳👍🤝😊
बहुत अच्छे हाइड्रोलिक के बारे में लीवर के बारे में अच्छी जानकारी प्राप्त हुई हमें धन्यवाद भैया चलो लीवर के बारे में कुछ तो पता चला पहले अनजान थे स्लो फास्ट के बारे में
You welcome Sir thanks 🇮🇳👍😁
@@AbdulKurad sir ye jo liver setting ke liye weight lgta hai ye kitne kg ka hai btaye sirr
Sir weight btade kitne kg ka hai me bi tractor mechanic ka Kam krta hmm
@@singhfarmerz578 4 Paune Ka Hota Hai
@@AbdulKurad thanks ustaaad ji
आपने कितना आसान तरीका से समझाया ऐसा समस्या मेरा ट्रेक्टर में पंद्रह सालों से था मेकेनिक लोग ठीक नहीं कर पा रहे थे आपको कोटी कोटी धन्यवाद
बहुत बहुत धन्यवाद सर जी आपका 🇮🇳👍
sri g pa ka namber nahi aa send karo ga
Bahut badiya kaam karte hain sar
Dhanyvad sir aapka 🇮🇳👍😁
Aap Hamare liye bahut mehnat karte ho Aapka kaam mere ko bahut achha lagta hai sir
Sir aap jese mahan logoki duva multi he sir jazah kallah 🇮🇳👍😁
Good job Abdul bhai dhanyvad 👌👌👌👌
Thanks pardip bhai 🇮🇳👍😁
काम की जानकारी दी है अब्दुल भाई
Dhanyvad sir aapka 🇮🇳👍😁
omaram jangid अब्दुल भाई आपका नम्बर दिजीये मेरे ट्रेक्टर कि हैड्रोलीक खराब है,,९६६९७५४६५५
Sir main aap ki har video dekhta hu
Good sir ji thanks you 🇮🇳😊👍
Abdul Kurad Great Ap Logo Ko Thik krke Dete ho Ap ka dhanywad 💕😁
You welcome Sir 🇮🇳😁
@@AbdulKurad ap Kaha Se Ho G
Sir me Gujarat se hu OK sir thanks 👍
Abdul JI can you do some repairs videos on Universal tractor{Fiat} 550&640 hydraulic setting & clutch ,brake job or engine service. love the way you teach thx
Good job Abdul bhai
Thanks sir 🇮🇳👍
Nice
Thanks malaram 🇮🇳👍😁
Good job bhai
Thanks you sir ji 🇮🇳👍😊
Thanks you sir Naresh Jagran guru dev🙏🙏🙏🙏🙏🇮🇳🇮🇳
Bahut Bahut Dhanyawad Sir Ji 🇮🇳 👍🤝😊
Good abdul bhai 👌👌👌👍
Thanks sir 🇮🇳👍😁
Very nice bro
Thanks you sir ji 🇮🇳👍
Very important this video Sir thanku
You welcome Sir 🇮🇳🚜😁
Super sir
Thanks sir ji 🇮🇳👍🤝😊
Thanks❤ for me🙏🙏 अब्दुल भाई जी
Thanks sir ji 🇮🇳👍
Very Nice work
Jazah kallah bhai 🇮🇳👍😁
Thanks you sir🙏🙏🙏🙏🙏🙏🙏🇮🇳🇮🇳
Thanks Sir Ji 🇮🇳👍🤝😊
Good job dear
Thanks you sir ji 🇮🇳😊👍
dahut sundar sir
Dhanyvad sir aapka 👍
Abdul Bhai aapka kam bahothi acha he aor aapka samjane ka tarika bhi bahot hi accha he aasani se samaj me aajata he aesehi video ham kisano ke liye banate rahna ise hame kafi sahai milti he aapka dhanyvad abdul khai👌🏽👌🏽👍
Punitbhai aapka bhi bahot bahot dhanyvad 🇮🇳👍🚜😁
Abdul Bhai hamari lift bhi bhut awaz kr rhe h implement jodne pr
હાડ્રોલિક નુ કામ ખૂબ સરસ રીતે થયું છે અબ્દુલભાઇ આવુ કામ તમારા જેવા સારા કારીગરજ કરી શકે છે.👌👌👌👌👌👌👌👌
Dhanyvad tushar bhai KAKA na tractor nu hydraulic nu su rijelt che 🇮🇳👍😁
@@AbdulKurad hydrulic ok che
Thanks tushar bhai 👍😁
Thanks Abdul bhai 👍🇮🇳🚜🚜🚜🚜
You welcome ustad thanks 🇮🇳👍😁
Uttar Pradesh Bar
Hindustan hydraulic fitting
Very good
Thanks sir ji 🇮🇳👍🤝😊
Guruji very very good👍
Dhanyvad sir aapka 🇮🇳👍
very helpful video sir👍,i am from ASSAM Sir😊
Good sir ji thanks you 🇮🇳👍
Aapka kaam aacha hai iselye aap price batna
વાહ અબ્દુલ ભાઇ વાહ
Thanks sir 🇮🇳😁👍
@@AbdulKurad ki ap apna mobile no dene ka kirpa karoge
Sir 245 mark ki liver setting ki video v laye
Ok sir ji kabhi uska job aayega to banaunga ok sir ji thanks 🇮🇳👍🤝😊
Good job
Jazah kallah bhai 👍😁
Salamwalekum Abdul bhai
W Salam Sir Ji sukriya 🇮🇳👍🤝😊
Thank you ustaad ji ❤️❤️❤️❤️....
You welcome Sir ji thanks you 🇮🇳👍😊
Abdul Bhai namaste aabhar
Dhanyvad sir aapka 👍
Sar ji mere pas massey 1035 di 97 model ka haidrolic ripeyar karana hai krpya achcha makenik btaye .Up me basti se ,
Sir Massey Ferguson 245 93 model ke hydraulic lift nka lever ki setting kaise hoti hai batane ki kripa kijiye.
Sir ji kabhi uska job aayega to banaunga ok sir ji thanks 🇮🇳👍🤝
Thanks for you 😌 god bless you 😌
Thanks sir ji 🇮🇳👍🤝😊
Aap fany Hu
Thanks you sir ji 🇮🇳😊👍💖
Good sir
Thanks bhai 🇮🇳👍
Thanks for replying am realy very happy to hear you
You welcome sir ji thanks you 🇮🇳👍
Good
Thanks sir 🇮🇳👍😁
Abdul bhai ye pular mere liye bhi bejo
Good 👍👍👍👍👍
Dhanyvad sir aapka 🇮🇳👍🚜
अबदुल भाई ईद मुबारक भाई ये पोजिसनलिवर व कनटरोल लिवर बिच मे रखते है कया
Hello abdul bhai
Thanks you sir ji 🇮🇳👍
हम भी ठीक हैं अब्दुल भाई
Thanks sir 🇮🇳👍😁
1035 di ka Hayrolic on off valve lagana he kese lagte wo vidio.....he to bhejo...
Sir kabhi job ayato banaunga OK sir thanks 🇮🇳👍
Nice sir swaraj ka drop settings ka video dalo
OK sir thanks 👍
Aya ki Nahi job swaraj ka
Okkkk thanks
Sir swaraj ka Engine ka video
brother massey ferguson 7250 hydraulic filter change video upload karo
गजब भाई गजब अब्दुल भाई कैसे हो नरेश सर जी कैसे हैं
सौरभ सर हम थीक है और उस्ताद भी मजे मे है आप सुना ओ आप कैसे हो धन्यवाद सर आपका 🇮🇳👍
Ustad ji Mere Paas tafi 30 hi main uska pump karaya hai uski Puli par do Nishan hai kaun se Nishant par drop setting karni hai
Sir apse ek question hai ki left ki setting se pahale pc and dc livar ki position keya honi chahiye
अब्दुल भाई ऐसी सेटिंग महिंद्र ट्रैक्टर में हो सकती है क्या स्पेशल टोल से जरूर बताएं
Abdul Bhai hamare massy. 1035 tractor khet me chalate chalate hydrolic apne app khud uper ho jati hai kya samsya ho Sakti hai
Sir mere pas swraj 735 fe 1998 modal ka he isme hidrolik ka red vale che kaltivetr uthta ni he or bleak che 5 inch hi uthta he or chalu me thi dire dire utar jata he sir to hidrolik me kya vajja hogi sir ??
सर आपका nambar चाहिए आप कहाँ रहते है हमारे ट्रेक्टर में ये सारे परेसानी हैं और कितना पैसा लग जायेगा plase रिप्लाई कीजिये गया आपको बहुत बहुत धनयवाद
Sir ji me Gujarat palej se hu ok sir ji dhanyvad aapka 🇮🇳👍
4wd kaise banaya vdo mai batay Massey Fargoson
sar jee ya jo haudrlic specal tuls ko istmal karta h wo only mase m hota h ki all trackret m use hota h
Sir ye only Massey ke liye he ok sir ji thanks you 🇮🇳👍😊
@@AbdulKurad sir thanks.
Sir lift upar karne par khad khad ki aawaz aati hai kya kharab ho sakata hai
सर जी आपका ट्रैक्टर कोनसा है बताना ओके सर जी धन्यवाद 🇮🇳👍
Isky agy jo special tool laga kr adjustment krty hyn uski humy measurement lenght or weight to batyn ap ka shukria hoga jnb.😊😊
Setting Lever Springs For MF35 Hydraulics
Making the settings on the lever springs for the Massey Ferguson 35 hydraulic system is quite a fiddly job, and the method is shown in detail with a written description of the process may also help.
The spring balance should be attached at the very end of the levers So here it is...
• Loosen retainer nut and eccentric cam.
• Make sure quadrant levers are set at their sector marks. The round lever exactly over where it says ‘FAST’, the square lever next to where it says ‘DRAFT’ between the two dots and exactly where the arrow is.
• Make sure the lift arms are in the fully lowered position. (that is upwards if the top cover is flipped upside down).
     
• Make sure your spring balance is connected right at the top of the lever (if it is connected lower down the lever it will require more force to move the lever).
• When 3 lb. of pressure is applied it should only just spring it into contact with the front of the slot in the lever support bracket.
• Obviously adjustment of the spring pressure is made with the self-locking nut on the guide rods.
After this adjustment is made the eccentric cam can be moved around into firm contact with the cam arm and the nut tightened. The above adjustments can be checked - move the operational lever from its sector marks into the response range, as the lever leaves the ‘FAST’ position the levers that we set with the spring balance should begin to move to the rear of the guides. The adjustment is very fine and fiddly. It is often right at the end of the movement of the levers where the 3 lb. can be achieved.
The setting is 3 lb. (1361 grams) of force to move the lever. The reason for this is that this equals the force applied by the control valve spring when the assembly is fitted and connected in the tractor. It is a very difficult setting to make and when using a spring balance the 3 lb. setting cannot ever be particularly accurate. Another method would be to attach a piece of string to the lever and pass this over a roller with a 3lb weight hanging off the bottom of the piece of string.
भाई साहब नमस्कार, क्या आप छत्तीसगढ़ वालों को सर्विस दे सकते हो क्या। मुझे अपने ट्रेक्टर पे काम करवाना है।ईंजन, हाइड्रोलिक,स्टेरिंग पे। कृपया बताएं धन्यवाद 🙏🙏🙏
नही सर जी धन्यवाद आपका 🇮🇳👍🤝😊
ટ્રાન્સફર વાલ્વ ( લોક)નવા મોડલ નો ફીટીગ કરી દીયો અબ્દુલ ભાઈ.👍👌
Ha sir ye bhi thik he thore Dino baad oil likej karta he ok sir thanks 😁
Sir hamare Massey 245 97 model hai
Heat hota hai acid daalkar saaf kar sakte hay
Sir humeko Engine, lift , clach peti eska ketne. Rupay lagige PL sir aap batna
abdul bhai draft aur position lever mein.filler gauze ka kya size hai....aur slow fast mei gauze size kitna rakhna hai plz btaye....
Sir ji uska pura video dala hai ok sir ji thanks 🇮🇳👍🤝
bhai hamne setting ki thi.lekin lift lever bilkul neeche karne par bhi lift uper uth rhi hai ...kya setting theak nhi kya.?????
@@harpreet2683 Ha sir ji aap se uska setting sahi se nahi hua is liye ok sir ji thanks 🇮🇳👍🤝
सर जी मेरे पास मैंसी का 9500E 50hp ट्रैक्टर हैं जिसकी लिफ्ट ऊपर करने पर स्लो उठती है इसका क्या सॉल्यूशन हो सकता है सर नवा ट्रैक्टर है
Please sir reply
Harjeet Singh 👊👊👊👍
Thanks you sir ji 🇮🇳👍😊
Sir m. F hydrulic lever seting. S. P. C tool. Ka weat. Kitna hotahai. Plijes. Human. Batein
Sir 3 pond ok sir ji thanks 🇮🇳👍🤝😊
सर जी मेरे पास 1035 40hp आइल बेंंक्र है तो आइल कौन सा डालु
Sir Ji Usme OIB Oil Dalta Hai Ok Sir Ji Thanks 🇮🇳👍🤝😊
Sir help karnataka hydraulic setting problem please instrument
Sir ji pozisan livar set krte samy position livar ki position down rahni chaiye kya aur draft livar ki BHI position batya sir ji
Sir fir video me aapne kya dekha saaf bataya huva he dekhlo ok sir thanks 🇮🇳👍
245कादैखनाहै
मेस्सी ट्रेक्टर 1035 डी आई आयल ब्रेक वाला में हाइड्रोलिक आयल कौन सा वाला डाले सर जी
मेस्सी ट्रेक्टर 1035 आयल ब्रेक में हाइड्रोलिक आयल कौन सा डाले बताये सर जी
Sir mere pas masssey ka 6028 mini tractor he, sir iss tractorki hyatrolick kaise set kare
slow fast roller mein kitni fiiler gaze set karni hai sir ji.
Bhai rem clander ka kya price hai
Massey 1035 Di ful haydrolic ripe ring me kitna kimat lagega
Sir ji sawraj735 tairali lod rahta hai to nahi utha pata hai jabki khali me utha leta hai kya samsya hai
Bhai jaan asehi ander se ekjest ka koi beja batao
Sir ap dono liver ki position ki kaha rakhar kar setting karte he vo batana
Vese to mene ye vala liver setting ka vidieo 2 bara dekha magar ise muje liver ko kaha rakh kar set kaete he ye pata nahi chalata
Sir how much weight you hanging on livers to adjust spring
Sir ji aapne video me kya suna mene bataya huva he ok sir ji thanks you 🇮🇳👍😊
Setting Lever Springs For MF35 Hydraulics
Making the settings on the lever springs for the Massey Ferguson 35 hydraulic system is quite a fiddly job, and the method is shown in detail with a written description of the process may also help.
The spring balance should be attached at the very end of the levers So here it is...
• Loosen retainer nut and eccentric cam.
• Make sure quadrant levers are set at their sector marks. The round lever exactly over where it says ‘FAST’, the square lever next to where it says ‘DRAFT’ between the two dots and exactly where the arrow is.
• Make sure the lift arms are in the fully lowered position. (that is upwards if the top cover is flipped upside down).
     
• Make sure your spring balance is connected right at the top of the lever (if it is connected lower down the lever it will require more force to move the lever).
• When 3 lb. of pressure is applied it should only just spring it into contact with the front of the slot in the lever support bracket.
• Obviously adjustment of the spring pressure is made with the self-locking nut on the guide rods.
After this adjustment is made the eccentric cam can be moved around into firm contact with the cam arm and the nut tightened. The above adjustments can be checked - move the operational lever from its sector marks into the response range, as the lever leaves the ‘FAST’ position the levers that we set with the spring balance should begin to move to the rear of the guides. The adjustment is very fine and fiddly. It is often right at the end of the movement of the levers where the 3 lb. can be achieved.
The setting is 3 lb. (1361 grams) of force to move the lever. The reason for this is that this equals the force applied by the control valve spring when the assembly is fitted and connected in the tractor. It is a very difficult setting to make and when using a spring balance the 3 lb. setting cannot ever be particularly accurate. Another method would be to attach a piece of string to the lever and pass this over a roller with a 3lb weight hanging off the bottom of the piece of string.
Kamlesh up
Thank Sir Ji 🇮🇳👍🤝😊
साहब मेरे पास massey 245 है 2015मॉडल और ट्राली मे बहुत कम जोर करता है क्या क्लच की दिक्कत है या कुछ और दिक्क़त है बताये
हा ऐसा भी हो सकता है चैक कर वा लो जोभी होगा पता चलेगा ओके सर जी धन्यवाद आपका 🇮🇳👍🤝😊
@@AbdulKurad बहुत बहुत धन्यवाद जी 🙏🙏
पट्टी और रोलर मे कितना थाउजंट अंतररखना है.
કલેગ રીપેરીંગ
नमस्ते भाई मुझे mahindara 275 old model ट्रॅक्टर को वॉटर सेपरेटर लागवाना है आप उसके उपर व्हिडीओ बनासकते हैं
Sir muje spacial tools lena he company ka kaha milega ya to aap mangavado sir please help
Liver stand genad ka bjan ky h k ha mil ta h
🇮🇳🇮🇳🇮🇳👆👆👌👌👍👍
Thanks you sir ji 🇮🇳👍😊
Sir Mahindra 265di ki hydrolic setting spesal tool se ki jati hai sir hamare tractor ki hydrolic over hokar phas jati hai
Sir Messi fargusan ka special tool khud banwana padta hai ya dukan se kharidna hai
Sir ji company se magana padta hai ok sir ji thanks you 🇮🇳👍😊