Hello. If question - how to replace ceramics burrs on Saeco grinders - than I got answer ))) To disattach burss - just turn them anti-clockwise on small degree (think about 10 degrees enough). Bottom burr will disattached easily, but for replace top one - you must clean 3 hols from up and down of Top burrs holder (in these holes - there is 3 ears of burrs, that holds it inside black ring with tooth)
Добрый день , вчера приобрела кофемашинку Philips EP2220/10 . Все по инструкции собирала , настраивала , ваши видео тоже помогли мне. Сделала кружек 5 кофе . У меня там где должны быть шайбы с использованным кофе - много выды , а кофе лежит на дне
Добрый. Попробуйте установить крепость на максимум. И попоробуйте сделать регулировку помола - сначала мин возможный, сделайте 2 чашки. Проверьте. Если не помогло - сделайте помол на среднем значении. Подействует тоже со 2ой чашки. Крепость всегда держите максимальную.
@@OlegPC здравствуйте ещё раз . Делаю только на Макс крепкости но проблема осталась , вода в перемешку с кофе вместо шайб и там где должна быть только вода в ней тоже кофе . Это проблема ? Или ничего страшного ?
@@user-ol4zm9rk6i Немного воды останется после стартовой промывки и она сливается в лоток отходов - получается там «болото». Это норм. Другое дело - если вода сливается вместе с приготовлением кофе - это уже неисправность.
Hope you can help. I have a Saeco Spidem that is about 12 years old. We cleaned the gears and now the grind is very course. The "pucks" are watery and not well formed. This, of course, makes the coffee not the best and uses a lot of coffee beans. I have adjusted the grind to the finest using the knob while it was grinding and it did not make any difference. Please help!
Hello. Try to re-assemble grinder - something incorrect. Maybe top burr holder doesn’t fit inside ring-regulator with holes. Maybe these ring-regulator get some lift from one side (with time - it’s holding ears - wear out a little). So - just watch your grinder closely and try to understand - what’s wrong
Hi. I heard that adjustments should be made while the grinder is runnig. I didn’t know that and I turned the knob from finest to the mid point a few times. Is there a possibility that I damaged the grinder?
So basically you push it all the way to the end until the burrs touch? And then go back 3 clicks? How much is the extraction time now compared to before? I get 17 seconds now at finest knob setting
About tuning grinder - you are right. About extraction - such thing in automatic coffee machines is questionable - because you can extract any time that you want (just set new water level for button “espresso” or “americano” or any over. So 17 seconds can mean any cup volume, differ from grind size. My personal opinion - coffee machine can make about 70-100ml of nice coffee, other volumes are strange and not pleasant taste. Of course these numbers can vary from machine to machine
Доброго вечора! Разобрал кофемолку чтоб поменять мотор, но после замены она мелит слишком крупно. Пытался в ручную прокрутить верхний диск, даже когдо он закручен до упора, жернова не сопрекасаются. В чем может быть проблема?
Ни в чем. При затянутых жерновах - и правда есть зазор между жерновами. Они не касаются. А то что мелет крупно - наверно, ответ на «почему сгорел мотор» - что-то заклинило жернова ( при этом «побило» нарезку на них). Вот жернова и крупно мелят. Это если собрана кофемолка точно правильно.
Is there a way to adjust the amount of beans that the grinder grinds? Mine it only grinds for 3 seconds and seems like only 1/4 of the amount of coffee required for a shot. Coffee tastes watery and weak. Wondering if there is an adjustment on the grinder for a longer grind
We can only help machine to adjust more coffee grind time - but not to command such adjustment. So, first make full repair of brew unit ( hardly moving brew unit - advices to machine to grind less because it full of coffee (machine understand such)). Secondly - clear grinder inside and add new lubricant to moving metall parts of grinder. So our grinder can grind more because all it power will be send on grinding, but not on moving parts of grinder). Thirdly-to lubricant all plastic gears of brew unit motor
Hi there again. may i know if this grinder adjustment works for my Philips automatic. i know it uses the same Saeco grinder but it does not require a screw key to turn the adjustments
Hello thankyou for this video.. after making this adjustment, at what position should the knob adjuster be installed? Should it be installed so that once all the covers are installed, the dot is pointing to the smallest coffee bean size with no more fine adjustment - to prevent damage? Or is it OK to adjust a bit finer? OR is x3 gear teeth out maximum finest?
Hello. When you adjust grinder to closest grind stones position on doesn’t working grinder - always possible to regulate grinder even finer on working grinder. A think, after adjusting to most finer position, when you start your grinder (making cup of coffee) , you can make 3 clicks (approximately) finer grinds without damaging you grinder. Of course you must check yourself by hearing noise of working grinder - if you hears hard and slow work of motor - it signals that you at finest grind size position.
Hello. It’s just simple action - just turn grind stones anti-clockwise (if I right). When you look closely to holder of bottom grind you will guess (by holes inside holder) that turn you need to do to release grind stone. This rule is acceptable to top grind stone holder.
This is ,usually, no problem. If you can find “just now” discarded coffeemaker - about 50% chance it will be or “ok” or need only clean, or chip repair needed. Biggest problem - find it before “garbage mafia” takes it. They sort “electronic” units and sell to the foreigners ( mostly from Ukraine, Belorussian, russian)
Thank you for the video man! is it possible for you to produce a video to show us how fine is the grind now? maybe can take a look at the coffee grounds after extraction - the puck
With this question - there is a difference between results of grinding from grinders with different work times (portions of coffee). So , in general, grind size must be much smaller than sugar particles. About 2-3 times.
Thank you very much for the video. Do you have any videos replacing ceramics to grind coffee?
Hello. If question - how to replace ceramics burrs on Saeco grinders - than I got answer ))) To disattach burss - just turn them anti-clockwise on small degree (think about 10 degrees enough). Bottom burr will disattached easily, but for replace top one - you must clean 3 hols from up and down of Top burrs holder (in these holes - there is 3 ears of burrs, that holds it inside black ring with tooth)
@@OlegPC thank you very much for your help ☺️
@@lcanelas87 Your welcome! My pleasure
Добрый день , вчера приобрела кофемашинку Philips EP2220/10 . Все по инструкции собирала , настраивала , ваши видео тоже помогли мне. Сделала кружек 5 кофе . У меня там где должны быть шайбы с использованным кофе - много выды , а кофе лежит на дне
Добрый. Попробуйте установить крепость на максимум. И попоробуйте сделать регулировку помола - сначала мин возможный, сделайте 2 чашки. Проверьте. Если не помогло - сделайте помол на среднем значении. Подействует тоже со 2ой чашки. Крепость всегда держите максимальную.
@@OlegPC Спасибо попробую , я делала на минимальной крепкости
@@user-ol4zm9rk6i Тогда точно крепость увеличенная - поможет. Когда мало кофе в заварном блоке - не формирует таблетку и получается «жижа»
@@OlegPC здравствуйте ещё раз . Делаю только на Макс крепкости но проблема осталась , вода в перемешку с кофе вместо шайб и там где должна быть только вода в ней тоже кофе . Это проблема ? Или ничего страшного ?
@@user-ol4zm9rk6i Немного воды останется после стартовой промывки и она сливается в лоток отходов - получается там «болото». Это норм. Другое дело - если вода сливается вместе с приготовлением кофе - это уже неисправность.
Hope you can help. I have a Saeco Spidem that is about 12 years old. We cleaned the gears and now the grind is very course. The "pucks" are watery and not well formed. This, of course, makes the coffee not the best and uses a lot of coffee beans. I have adjusted the grind to the finest using the knob while it was grinding and it did not make any difference. Please help!
Hello. Try to re-assemble grinder - something incorrect. Maybe top burr holder doesn’t fit inside ring-regulator with holes. Maybe these ring-regulator get some lift from one side (with time - it’s holding ears - wear out a little). So - just watch your grinder closely and try to understand - what’s wrong
Thank you so much. We will be trying this today.
Not at all
Hi. I heard that adjustments should be made while the grinder is runnig. I didn’t know that and I turned the knob from finest to the mid point a few times. Is there a possibility that I damaged the grinder?
Hello. There are any chances that you can damage yours grinder by adjusting it just 1-2-3 times. Think, it is working well.
So basically you push it all the way to the end until the burrs touch? And then go back 3 clicks? How much is the extraction time now compared to before? I get 17 seconds now at finest knob setting
About tuning grinder - you are right. About extraction - such thing in automatic coffee machines is questionable - because you can extract any time that you want (just set new water level for button “espresso” or “americano” or any over. So 17 seconds can mean any cup volume, differ from grind size. My personal opinion - coffee machine can make about 70-100ml of nice coffee, other volumes are strange and not pleasant taste. Of course these numbers can vary from machine to machine
Доброго вечора! Разобрал кофемолку чтоб поменять мотор, но после замены она мелит слишком крупно. Пытался в ручную прокрутить верхний диск, даже когдо он закручен до упора, жернова не сопрекасаются. В чем может быть проблема?
Ни в чем. При затянутых жерновах - и правда есть зазор между жерновами. Они не касаются. А то что мелет крупно - наверно, ответ на «почему сгорел мотор» - что-то заклинило жернова ( при этом «побило» нарезку на них). Вот жернова и крупно мелят. Это если собрана кофемолка точно правильно.
Is there a way to adjust the amount of beans that the grinder grinds? Mine it only grinds for 3 seconds and seems like only 1/4 of the amount of coffee required for a shot. Coffee tastes watery and weak. Wondering if there is an adjustment on the grinder for a longer grind
We can only help machine to adjust more coffee grind time - but not to command such adjustment. So, first make full repair of brew unit ( hardly moving brew unit - advices to machine to grind less because it full of coffee (machine understand such)). Secondly - clear grinder inside and add new lubricant to moving metall parts of grinder. So our grinder can grind more because all it power will be send on grinding, but not on moving parts of grinder). Thirdly-to lubricant all plastic gears of brew unit motor
Hi there again. may i know if this grinder adjustment works for my Philips automatic. i know it uses the same Saeco grinder but it does not require a screw key to turn the adjustments
Yes, your machine have got the same grinder ar Saeco machines does. Except handle - regulator. So they are on 99% same.
Hello thankyou for this video.. after making this adjustment, at what position should the knob adjuster be installed? Should it be installed so that once all the covers are installed, the dot is pointing to the smallest coffee bean size with no more fine adjustment - to prevent damage? Or is it OK to adjust a bit finer? OR is x3 gear teeth out maximum finest?
Hello. When you adjust grinder to closest grind stones position on doesn’t working grinder - always possible to regulate grinder even finer on working grinder. A think, after adjusting to most finer position, when you start your grinder (making cup of coffee) , you can make 3 clicks (approximately) finer grinds without damaging you grinder. Of course you must check yourself by hearing noise of working grinder - if you hears hard and slow work of motor - it signals that you at finest grind size position.
@@OlegPC Thanks again for your help.
@@Beyond3dGraitec My pleasure. Hope, it will help.
Hi.Do you have a video where I can see how to replace the Saeco Minuto ceramic grinders? Thanks
Hello. It’s just simple action - just turn grind stones anti-clockwise (if I right). When you look closely to holder of bottom grind you will guess (by holes inside holder) that turn you need to do to release grind stone. This rule is acceptable to top grind stone holder.
Thank you for the video!🙂
My pleasure.))) All coffeemakers can made much better coffee. This is first step to “great home coffee”
Wow, this is serious! We are very interested in how to find a 10-year-old coffee maker in the trash and poke around in it to drink coffee😏
This is ,usually, no problem. If you can find “just now” discarded coffeemaker - about 50% chance it will be or “ok” or need only clean, or chip repair needed. Biggest problem - find it before “garbage mafia” takes it. They sort “electronic” units and sell to the foreigners ( mostly from Ukraine, Belorussian, russian)
Thank you for the video man! is it possible for you to produce a video to show us how fine is the grind now? maybe can take a look at the coffee grounds after extraction - the puck
With this question - there is a difference between results of grinding from grinders with different work times (portions of coffee). So , in general, grind size must be much smaller than sugar particles. About 2-3 times.
Do you have a video where I can see how to replace the Saeco Minuto ceramic grinders
It’s so simple actions, that we don’t need to watch any video ))) Just turn grind stone a little in holders (of grind stone. Top and bottom holders)
Just turn ceramic (top or bottom) anticlockwise to release.
Hi. What if I turn all down to the minimum grinder and then I only turn x1 click and not x3 clicks? Can I do it or it will break my grinder?
Hi. All be all right. For security reasons, I recommend turn on 3 clicks, but if you want, you can , on your own risk, turn on just 1 click.
Spasibo)
You’re welcome !
👍👍👍
Дякую