Love the ingenious use of hidden magnets! (Behind to wheel on the wood tower. They help to “suck” to balls into the hole and keep them from falling out during the ride) This gives the unit a very clean look and likely contributes to the speed performance.
I believe you're mistaken. The balls stay in the wheel because the hole is drilled at an angle. You'll note that the wheel support tower blocks the balls from rolling out until they reach the desired position. The metal you see on the back of the tower is the nut securing the axle.
Yes, I think you are right! The holes seem to be drilled toward the edge to about half the depth and then toward the centre as the exit the other side. I now see how they fall toward the dented as the disk moves. Very delicate design! Love it!
I must be being really stupid but I'm not sure how the angles of the holes in this wheel works. Normally the hole is tilted so the marble rolls in, then the hole would be tilted the other way after 180 degrees of the wheel rotating so the marble rolls out again, but in these cases the marble enters and leaves on the same side of the wheel. In your wheel the side the marble enters the wheel and the side the marble leaves the wheel are different. -comment continued below-
Applications like these on a larger scale of course could have great uses in making power. I would ABSOLUTELY LOVE to see you make a perpetual motion power maker. You'd be a billionaire.... Or the rich people who own power companies would assassinate you lol
🔵 You evidently know quite little about physics, or you'd realize that the only way this device could make power would be if you sat there and CRANKED it!!
@crocket1221 there is a simple trick to getting the wires bent: you take a lenght of wire and bend it around a cylindical object, eg a pipe, a dowel or a glass in oder to make parallel curves you simply take a shorter lenght of wire for the inside and the longer piece for the outside and bend them both around the same cylinder then align them until they are exactly parallel to each other. For the end loops you bend a short piece around a dowel and solder that into place
You do such neat stuff. I love watching all those videos. Where did you get the gear down motors? Would love to get a few of them and make something with kids.
change the return arm to drop the balls farther from the wheel, then turn the beveled holder into a longer channel so that the balls are basically sitting in a single file queue
Way cool ! If you make the holes at different positions you could create a drum beat ;-) Add a little Piezoelectric mic and a small amp and speaker ;-)
so how fast did it go? like 2~3 balls per second? then that would be 120~180 per min. and can you somehow make it faster? everything faster is better. you found any use for it yet?
The only way I can see this being possible is if the marbles has to roll uphill slightly when they enter the wheel at the bottom, is this what happens? p.s. nice machine
Are the holes drilled from one side or are they drilled from both sides at different angles. I have not been able to get the balls to go in one side and out the other.
Thermodynamics principle is misconception. Perpetual Motion Machine is possible. See bellow The WORK OUTPUT is more than double the WORK INPUT. A 15 ball billiard pool to be strike by white mother ball When I computed the work done in pool (billiard) the white mother ball break the 15ball. F = 30lbs (White Mother Ball); D = 3ft (Distance from the white mother ball to the first ball to strike) SOLVE FOR WORK INPUT W = F X D; W = 30lbs x 3ft = 90Ft.lbs SOLVE FOR WORK OUTPUT First two ball extreme corner of the billiard ball 2 out of 15 ball W = F X D; W = 30lbs x 3ft = 90ft.lbs X 2ball = 180 ft. lbs The remaining ball (13pcs ball) can produce more than 90 ft.lbs The computation shows that the output work done is higher than the input work done. That principle can make free energy machine Appreciated for your reply Thank you. Abel Urbina Abel Urbina Free Energy Super Machine
The holes are tilted so at the bottom the balls enter the holes downward whil at the last 90 degrees of the wheel the holes are tilted downward so that the ball roles out. There is some kind of bar at the other side to prevent the balls from dropping out and they come out right onto the track Am i right?
Was actually looking for the clip of the tiny wheel from The Office but wow! This was so much cooler! I love it!
Love the ingenious use of hidden magnets! (Behind to wheel on the wood tower. They help to “suck” to balls into the hole and keep them from falling out during the ride) This gives the unit a very clean look and likely contributes to the speed performance.
I believe you're mistaken. The balls stay in the wheel because the hole is drilled at an angle. You'll note that the wheel support tower blocks the balls from rolling out until they reach the desired position. The metal you see on the back of the tower is the nut securing the axle.
Yes, I think you are right! The holes seem to be drilled toward the edge to about half the depth and then toward the centre as the exit the other side. I now see how they fall toward the dented as the disk moves. Very delicate design! Love it!
This machine proudly deserves the name: energy dissipation machine
Great stuff, denha. All of your mechanisms & videos are very well done.
You should really sell these! The sound of it is really soothing making me sleepy :P
I just spend 5min of my life to see balls fall down oO and I love this oO
Hermoso, casi hipnótico de ver.
"But, mom, I want to ride that wheel again!!"
Fuck you
@@hungvo7445 no u
Very good, quite ingenious in fact! 10/10
I must be being really stupid but I'm not sure how the angles of the holes in this wheel works.
Normally the hole is tilted so the marble rolls in, then the hole would be tilted the other way after 180 degrees of the wheel rotating so the marble rolls out again, but in these cases the marble enters and leaves on the same side of the wheel.
In your wheel the side the marble enters the wheel and the side the marble leaves the wheel are different.
-comment continued below-
FINALLY!
You finally ran a machine at some nice speeds!
Super video.
Great 👍👍👍 creativity
Very nice
Very good craftsmanship !
Чем бы детя не тешилось,лишь бы не плакало.
Applications like these on a larger scale of course could have great uses in making power. I would ABSOLUTELY LOVE to see you make a perpetual motion power maker. You'd be a billionaire.... Or the rich people who own power companies would assassinate you lol
🔵 You evidently know quite little about physics, or you'd realize that the only way this device could make power would be if you sat there and CRANKED it!!
@crocket1221 there is a simple trick to getting the wires bent: you take a lenght of wire and bend it around a cylindical object, eg a pipe, a dowel or a glass in oder to make parallel curves you simply take a shorter lenght of wire for the inside and the longer piece for the outside and bend them both around the same cylinder then align them until they are exactly parallel to each other. For the end loops you bend a short piece around a dowel and solder that into place
You do such neat stuff. I love watching all those videos. Where did you get the gear down motors? Would love to get a few of them and make something with kids.
Of course I find this video after I asked you about the wheel holes the other day!
Could *HAVE* be a great metronome!
Congratulation! ... You just proved that a ball rolls downhill...
Лайк!!!!прикольная штучка
That was awesome !!
the holes are probably cone shaped, so they will be outwardly sloped no matter what direction they are turned
Isn't this so satisfying to watch?
change the return arm to drop the balls farther from the wheel, then turn the beveled holder into a longer channel so that the balls are basically sitting in a single file queue
Oh my God this channel is so good i love your content so much , i hope one day my videos could even be half as good as these.
that is such a satisfying sound...
Your test is passed 😁😁👍🏻 hahahah enjoy the sound
9/32 inch stainless steel ball.
0:00 Nintendo Switch Startup
Iove..u..Fc..2019..มันสวย..งามมาก
.
It makes a great sound at 2:15 - 2:30! We'll done. What are you using for a speed controler?
Its a brushed motor, so the only RPM control he has is with the voltage from the power source :)
Hey, I really love your creativity but may I ask, what types of motors do you use? That would really help.
looks like a dc motor, you can salvage them from old electronics or buy them online
Eu sou brasileiro vejo esses exemplares é só de brincadeira na realidade da vida não tem garantia de sucesso no desempenho do funcionamento.
With this sort of ingenuity you could probably open up a portal to another dimension..Be careful.
Игрушка для дитей. Молодец.
Super cool
Way cool ! If you make the holes at different positions you could create a drum beat ;-) Add a little Piezoelectric mic and a small amp and speaker ;-)
This time you didn't use your little chopsticks and everything went bananas!
If only I didn't have a screw lose and lost all my marbles I would try building this.
Hello 4 year old pun
Very cool. Also very good desk setup :)
Remember when Lucy & Ethel were at the end of the chocolate assembly line? This is the mechanical version. LOL Poor little machine.
why did i like this so much?
It is a good idea.
you should make it so that marbles can move the motor and there is 2 wheels for the motor to be able to rotate :D
What is the specification of your drive motor and where do you obtain these, Thank You
Why is the so mesmerizing? Do you sell these ? Amazing. Drew
It is not a cone.
However, the movement is the same.
Oh I just realised, another possibility is that the whole wheel is tilted, but it seems to me like the wheel is upright.
hi 👋 good evening ji wow awesm super 💞 Kiya baat 🌹 Kiya baat 🌹 very good video No 1 👌 and beautiful awesm 🌓🌓🌓🌓🌓🌓🌓🌓🌓🌓🌓🌓
I liked the part when the wheel turned.
I think i will pay top dollar for just that little contraption
4:43 Va a estallar!!! . xD
2010: no
2011: no
2012: no
2013: no
2014: no
2015: no
2016: no
2017: no
2018: no
2019: yass
TEST RUN,?
UNA RUEDA DE LA FORTUNA?
LAS PIEDRAS RODANDO,SE ENCUENTRAN?
so how fast did it go?
like 2~3 balls per second?
then that would be 120~180 per min.
and can you somehow make it faster?
everything faster is better.
you found any use for it yet?
I wanna ride on it
Very efficient! Well done!
This is the trial production for sale.
Do people buy from you this kind of marble machine?
even i dont see see the benefit : very nice construction
Do the holes have to be drilled at a 10 percent angle in order for the balls to drop ouit due to gravity?
The only way I can see this being possible is if the marbles has to roll uphill slightly when they enter the wheel at the bottom, is this what happens?
p.s. nice machine
An adjustment to youre wood ramp can make it run smoother
what kind of wire you use to make the slider? thankss
Are the holes drilled from one side or are they drilled from both sides at different angles. I have not been able to get the balls to go in one side and out the other.
yeah that's probably it, thanks, you're a genius!
Super ideas
Mesmerizing, I loved it.
Thermodynamics principle is misconception. Perpetual Motion Machine is possible. See bellow
The WORK OUTPUT is more than double the WORK INPUT.
A 15 ball billiard pool to be strike by white mother ball
When I computed the work done in pool (billiard) the white mother ball break the 15ball.
F = 30lbs (White Mother Ball); D = 3ft (Distance from the white mother ball to the first ball to strike)
SOLVE FOR WORK INPUT
W = F X D; W = 30lbs x 3ft = 90Ft.lbs
SOLVE FOR WORK OUTPUT
First two ball extreme corner of the billiard ball 2 out of 15 ball
W = F X D; W = 30lbs x 3ft = 90ft.lbs X 2ball = 180 ft. lbs
The remaining ball (13pcs ball) can produce more than 90 ft.lbs
The computation shows that the output work done is higher than the input work done. That principle can make free energy machine
Appreciated for your reply
Thank you.
Abel Urbina
Abel Urbina Free Energy Super Machine
Nice...i want it on top of my office table.. :)
The holes are tilted so at the bottom the balls enter the holes downward whil at the last 90 degrees of the wheel the holes are tilted downward so that the ball roles out. There is some kind of bar at the other side to prevent the balls from dropping out and they come out right onto the track
Am i right?
Truly amazing man, great job even tho i randomly found this video =D
Now I can say that I really love balls
what is the metal thing ? and what kind of marble did you use? metal or regular marble?
are these holes drilled at an angle?
I came. Did you come?
I'm too high for this.
Sayah suka
CF9417
X7un
ok buddy we can see that the power to the wheel has a spring jeez
Hello + Denha I loved your marble machine, if I could pass the measures is that I want to make one too.
Great work. I wonder how you make your motor turns slowly, but not fast.
you can buy geared motors... little gearbox on the motor.
So simple, So nice.
Work of art.
There must be 3-5 holes that is unused for this to work.
It's a mad house! A mad house!
It'll work better if upper rail will be little more horizontal
That is great 😂
04.47 original video start
soon you'll be able to make gatling guns
That is some awsome stuff!
Very good
Awesome job....
I really like that
Where do you buy these please tell
im not gonna be the same anymore
You are an inspiration! :D
cute art well done sir
it looks cute
Hola +denha me encanto tu marble machine , si me podrias pasar las medidas es que yo quiero hacer uno tambien.
3:00 watch 3x speed horse running sound
I would very much like to know where you buy your motors and gears.
+ボブBrueckner gizmoszone
denha seur
denha thank you.
John Velasco l
Bob Brueckner llllllll