Braun Series 9 shaver head Problem Do not replace! - FIX IT!
Вставка
- Опубліковано 4 лип 2024
- Braun Series 9 shaver head Problem Do not replace! - FIX IT!
Cabezal de afeitado Braun Serie 9 Problema ¡No lo reemplace! - ¡ARREGLALO!
Braun Series 9 Scherkopf Problem Nicht ersetzen! - REPARIERE ES!
Tête de rasage Braun Series 9 Problème Ne pas remplacer ! - RÉPARE LE!
مشكلة رأس ماكينة الحلاقة Braun Series 9 لا تستبدل! - اصلحه!
Braun Series 9 剃須刀頭 問題 請勿更換！ - 修理它！
Some people find that the head falls apart into bits and having to replace it. This simple video will show you how to piece it together again and you can continue to use it
thank you very good video
Thanks a lot , it is working now with me
Wish you all the best
Thanks a lot sir!. This video helped me figuring out which was the correct position of those miniature spring levers after completely taking apart my shaver head.
Thanks for letting me know that it helped you! Good luck.
This video is about putting the blades back together after cleaning them. It is very rare for the need to replace the blades. I have seen the blades being sold on eBay. I hope this helps.
Thanks for this video! I’m also having an issue at the disassembly stage. My bracket is metal and I can’t pull them apart like you have suggested in another comment - is your bracket plastic or is there a tab I should be able to press down to release it? Thanks again
Cleaning is pretty simple: Use water & dish soap (UK: Fairy Liquid) and submerge the bladed part into the mix while the shaver is running. Then repeat, with clean water. In a few minutes; all blades will be cleaned!
Note: You cannot dismantle the foils to access the blades.
I am confused? By taking apart the razor cartridge, where do I buy the NEW razor blades to replace the USED blades? How much & where do I buy them? Thanks!
Great video but it’s confusing when @ 2:03 you try to say you pull and they fall off the video skips. That’s the only issue but thank you for posting and helping out
Thank you for your comment! Every question/comment will aid someone in fixing their problem.
Sorry, that the video did skip at that point! The videos was made to help people to re-assemble the blades.
There are 2 tabs on each side of the blade assembly - when these are pulled apart the assembly will eject out.
Furthermore, the outer casing will only allow the blade to be inserted one way and not if they are turned 180 degrees.
I'm sorry, but I can't find these tabs you're referring to on each side of the assembly. I can't take the outer case off. Please show a picture or video of this.
@@daliscwbys1 I have exactly the same problem. I also cannot find the "tabs referred to, and don't know where to grab/apply pressure to "pull apart". All I can see in the video is fingers covering the sides. It's a great shame, because the inability to get the assembly out makes the advice in the rest of the video (which seems very useful...) essentially irrelevant. The reply to another comment below says "just pull apart the outside frame". But it is made of metal, there is nothing to grab hold of and I cannot figure how to pull it apart.
@@joemalvik me too. I can pull the sides apart but it is still attached to the short sides. Guess ill need to buy another head
Hi,
Thank you for your interest in this video! At 1:56 you will see that I pull apart from the sides. But the blades will not fall apart in this position! You need to have this top part facing down, so with gravity, the blades will fall apart! (It is difficult to film under the blades while pulling apart the sides!)
How do you take apart,? You just said you pull it apart but then it skipped over how to take the silver part off the black part.
If you look at 1:57 - just pull apart the outside frame and they all fall out.
Another thing that I forgot to mention: When all the blades are pushed back in - they will only go in one way! If you rotate the outer frame - they will not (hold) into the frame and keep falling out! I hope this information helps you!
At 3:16 I picked up the frame and made a WRONG statement! I said: "It does not matter which way you put the frame" the reality is, it DOES MATTER! If wrong way - then the blade will keep falling out!
I find the middle blades are jumping out on me. I can pop them back into the Shaver and just power it on, and they still pop out.
It's gotta be a manufacturing fault.
The 2 middle ones (Gold & Silver) MUST be put back in the right order! They both have 2 clips each. Therefore, FOUR clips/tabs, fitted side by side to slot into the bay.
If any one is in the wrong order they will keep falling out.
Also, the gold one is to the rear of the shaver, when holding it in your hand.
I hope this help, but I fear you may have broken the clips/tabs.
@WasteInkPads thank you for that info that's really useful info. I'll try and pull it apart and see if I can fix it using your video.
There is alot of Amazon reviews of others having the exact same issue so I believe braun needs to address this as it didn't happen with my original and 2nd replacement blades.
Issue my seems to he with my last 2 blades which typically break within 3-8 months but braun seems to he just replacing them.
Yet to pull it apart but I think I know the fault. The gold blade has 2 silver metal hook tabs that hook onto the bottom foil blade. Over time it I think it bends or stretches getting dragged up and down your face shaving leaving enough gap to pop out.
I still just need to pull it apart and bend it back towards the bottom foil blade so it has less free play but I think that's going to be the fix
Update I fixed it!! Thank you 😊
The two outer foil blades keep the two inner blades from popping out.
If the inner blades (gold and silver middle blades) pop out it's because their metal hooks have become bent and loose causing them to pop out.
The fix: follow the video but bend the inner blades connected to the foils out again to be more secure with the outside foil blades.
@@bign1667 Bless you! Thank you for your comments. I am sure it will help someone.
Is there a way to open the foil itself and clean the actual blades?
You can only clean the outer two and not the central one.
I'm referring to the outer foils. Can you open up the foil itself to access the blades?
Thanks
@@thematrix7225 Cleaning is pretty simple: Use water & dish soap (UK: Fairy Liquid) and submerge the bladed part into the mix while the shaver is running. Then repeat, with clean water. In a few minutes; all blades will be cleaned!
Note: You cannot dismantle the foils to access the blades.
where do you get new foils?
Try eBay!
The foils on the sides that are not coming apart for me, it’s the gold and silver bars that keep coming apart for me.
The outer silver (curved foils) should lift straight out. It is possible that dried debris is holding the foils down.
The inner gold and silver bars, will not lift out as they have tabs underneath. It is not necessary to remove the inner bars.
You can easily clean them with a brush or even under water. If the inners bars have fallen out and will not return - it is probably due to the tabs being broken. It may also mean that you are trying to return them in an inverted position and may need to rotate them and put then in the opposite position. I hope this helps.