nicely done! This type of plane is in my opinion the best to learn to fly with. nice that you also showed some measurements for possible replicators. respect for your construction insight. Healthy and friendly greetings from the Netherlands. Rob
This is what....is how....there you sit doing calculations...looking for alignment, angles...And this two pieces of Styrofoam without drawings glued together and went to fly...and it flies.....What the hell aerodynamics......I'm shocked...I laughed for a long time as he did it...BUT the guy a big laik....Coolibin of our time.....👍👍👍👍👍👍👍👍👍👍
good work. except 0642 (the mass of) these servos Should be located Forward-of the thirty percent of chord line. thirty percent is a multiplication by .3. there is No Reason for a pushrod to be short.! a good pushrod of any length can be fabricated, EASILY; using steel wire from a paperclip and a slender piece of wood or bamboo. the use of a metal main spar component has made the wing Heavier; that high-located mass has, in turn, has elevated the location of the model's center of mass (c-m). 0716 the horiz-stab Should have a Symmetrical profile.! the distance between the stabs and the wing is excessive; by about two inches. it is recommended that control surfaces NOT be located directly in the prop wash. the affects of this design mistake would be reduced IF an optimal thrust LINE were used. specifically, where an offset pusher thrust configuration is used, a certain amount of negative aoa Should be used at the motor mount. 0730 servos do NOT go at the tail.!!! in the case of the use of a t-tail, at least the elevator servo can easily be CORRECTLY not located at the tail. 0902 this is a less-than ideal thrust Line; because it results in unscheduled nose-down moment, any time that there is thrust.!!! a smaller diameter, stiff, EP prop SHOULD be used in this type of application. not a flexible SF prop. googletranslate
assalamualikum vaia. ami ekta rc plane banaisi kintu transmitter er sathe sobkicu kivabe setup korbo bojhte parci na mani mechanical problem golo milate parci na. . ei nie ekti video dile khub upokrito hotam
Thanks for you all about this wonderful work 🙏❤️🙏❤️🙏🙏 But It's possible to open the door to technical place to learn this in a place to learn and grow our mind to learn this all STYLE and take his Cash
Amio ekta banachi kintu bolen servo 2 ta kemne connect kore reciver er sathe connect korbo ami bhaptesi donotar wear side eksathe lagia pore partake lagie reciver er sathe connect kori dibo reply dien
Karya yang bagus kawan,lanjutkan.
thanks
Many people make planes but your work is clean ... And plane looks good
thanks
খুব সুন্দর হয়েছে 😊
thanks
good idea to land and take off from water,,,,, Good ...
thanks
Nice, flies better than the real Icon A5!
thanks
I like the world of aviation, and I want to build a plane like this
best of luck
Знаеш ли? За Milen Totev MESSENGER настройчик бригадър
Nice vidéo,nice plane !!!!!!!😍✈
thanks
Very nice build!!
Thanks!
Хорошо получилось
thanks
looks great 👍
Thank you! Cheers!
❤❤❤❤❤❤
thanks
Vai ami apner big fan❤😮
thanks
Best video on UA-cam 🎉🎉🎉
thanks a lot
@@RCLifeBD I shared your video on Aeromodelling group
thanks
Show beautiful
thank
🎉🎉 অনেক সুন্দর
thanks
Please tell the motor thurst angle???
0°
Nice !!!
Thanks!
nice bro
Thanks
Which kind of pipe you are using to give support to the wing and tail
jute
nicely done!
This type of plane is in my opinion the best to learn to fly with. nice that you also showed some measurements for possible replicators.
respect for your construction insight. Healthy and friendly greetings from the Netherlands.
Rob
thanks brother
you should of added landing gear that can go up and down so it can also land on land
right
@@RCLifeBD also if there is no water around and the propeller breaks but all the other electronics works, the landing gear will come in handy
This is what....is how....there you sit doing calculations...looking for alignment, angles...And this two pieces of Styrofoam without drawings glued together and went to fly...and it flies.....What the hell aerodynamics......I'm shocked...I laughed for a long time as he did it...BUT the guy a big laik....Coolibin of our time.....👍👍👍👍👍👍👍👍👍👍
thanks
❤❤❤
thanks
খুব সুন্দর ভিডিও 👍👍👍। স্যার একটা ভালো প্লেন বানাতে মোট কত খরজ হবে। আমি ক্লাস টেন এ পড়ি। আমি একটি প্লেন বানাতে চাই। আর আমি আপনার সব ভিডিও দেখি ❤❤❤❤❤।
15,000 ar moto lagbe
Motor thrust angel 15'+- hole ki problem ache
ji
Vai single 180 motor diye ekta rc plane er full build video den please 😢 .
deoya ache channel a
Please provide measurements also 😊
video valo kore dekhen mesurment dichi
ato sundor kore kivabe katen??😅😅
cesta korle shob e shomvob
@@RCLifeBD costep gula koi paisen??
order diya banaichi, lagle amar theke niyen ami bikri kori
good work. except
0642 (the mass of) these servos Should be located Forward-of the thirty percent of chord line. thirty percent is a multiplication by .3.
there is No Reason for a pushrod to be short.! a good pushrod of any length can be fabricated, EASILY; using steel wire from a paperclip and a slender piece of wood or bamboo.
the use of a metal main spar component has made the wing Heavier; that high-located mass has, in turn, has elevated the location of the model's center of mass (c-m).
0716 the horiz-stab Should have a Symmetrical profile.! the distance between the stabs and the wing is excessive; by about two inches. it is recommended that control surfaces NOT be located directly in the prop wash. the affects of this design mistake would be reduced IF an optimal thrust LINE were used. specifically, where an offset pusher thrust configuration is used, a certain amount of negative aoa Should be used at the motor mount.
0730 servos do NOT go at the tail.!!! in the case of the use of a t-tail, at least the elevator servo can easily be CORRECTLY not located at the tail.
0902 this is a less-than ideal thrust Line; because it results in unscheduled nose-down moment, any time that there is thrust.!!! a smaller diameter, stiff, EP prop SHOULD be used in this type of application. not a flexible SF prop. googletranslate
It shows that aesthetics aren’t everything everyone a paper bag can fly 😂
😜
assalamualikum vaia. ami ekta rc plane banaisi kintu transmitter er sathe sobkicu kivabe setup korbo bojhte parci na mani mechanical problem golo milate parci na. . ei nie ekti video dile khub upokrito hotam
onno channel ar video dekhen.
ami amon video upload dei na
ভাই ভালো দামে এবং ভালো মানেন Jet Engine Rc কিনতে পার বাজেট ৫০ হাজার মত আছে শুধু Engine কিনব ২ টি
apnar kotha kichu Bujlam na
@@RCLifeBD ভাই আপনার ফেইসবুক বা হোয়াট এপ নাম্বার টা কি পাওয়া যাবে
channel ar about a fb link deoya ache.
inbox koren
@@RCLifeBD ভাই আপনাকে ফেইসবুক নক করেছি
আমি আপনার fbআইডিতে friend recost দিয়েছি ধরেন😊
ok
Thanks for you all about this wonderful work 🙏❤️🙏❤️🙏🙏 But It's possible to open the door to technical place to learn this in a place to learn and grow our mind to learn this all STYLE and take his Cash
right
ভাই আপনার প্লেনটি কতটুকু কাজ সম্পুর্ণ হয়েছে কিছুইতো আপডেট দিলেন না।
kaj korle to update dibo. taka nai kaj bondho
Amio ekta banachi kintu bolen servo 2 ta kemne connect kore reciver er sathe connect korbo ami bhaptesi donotar wear side eksathe lagia pore partake lagie reciver er sathe connect kori dibo reply dien
apnake onek kichu shikhte hobe tar por banaite hobe
Ami onek video dechsi sikchi ami 3 ta servo diye ar ekta motor diye plane banabo
Abar ami ekta banaisi ami apnake photo dibo konkhane deoa jabe
You Should Improve Your Working Place
right but no money
Same to me
@@rojinaakter4884 jo hukum mere aka😄
❤❤❤❤
thanks
❤❤
thanks