How To Set Valve Lash On A Duramax Engine!

Heavy Duty Tie Rods, Lift Pumps, Diesel Parts Merch! key tags, decals and shirts!👍 truckmasterdie...
Buy Tie Rods Here 👉 truckmasterdie...
Subscribe to my new UA-cam channel: / @truckmastergarage9944
sptoolsusa.com use discount code truckmaster and save 10% Everything!
Instagram: @truck_master07
My Instagram @truck_master07
www.instagram....
Tire Streets Tires Link / use 15% Off coupon code truckmaster 👇
tirestreets.co...
hspdiesel.com
Coupon code: “truckmaster”
Anthem Wheels! www.anthemwhee...
Ryan’s Diesel Service ryansdieselser... 5%off turbo’s coupon code👉 truckmaster
Kodiak Truck North Prairie, WI 👉 kodiaktruck.com transmission, tcase and rearend coupon code truckmaster save 5%
Instagram @truck_master07
Mods done to the Truck!
EFI Live DSP5 Switch
HSP Air Intake Kit
68mm Street Turbo Ryan’s Diesel Service
60% Injectors Bitterroot Diesel
HSP Diesel YBridge
HSP Hot Side intercooler pipe
FASS Titanium 150GPH Lift Pump
FASS Fuel Sump Kit
MBRP 3inch Turbo Down pipe
PPE Race fuel valve
Ported fuel fitting
Transgo Jr Shift Kit
Kodiak Truck Transfer Case
Kodiak Truck AAM GOV Lock11.5 Rear end
PVC Reroute
PPE Stage 5 Built Transmission
Zone off-road upper control arms
PPE Stage 3 HD Tie Rods
6" Pro-comp suspension lift kit
5100 Bilstien Shocks
35/12.50/R22 DX12 Delinte
22x14 Instigators A776 Anthem Wheels
Trail Ready Front Bumper
Music by: suncloud
Boostautoparts 👉 boostautoparts...
#duramax #powerstroke #cummins

[@AlbertAGhazaleh]

Basically it same principle when you're doing a small or big block chevrolet, it's just a diesel instead of gas.
But it's awesome information to know!!

[@truckmastergarage9944]

I appreciate it

[@ricardoruiz6612]

GREAT STUFF!! love when you visit this shop and show the content.

[@truckmastergarage9944]

Thanks!

[@ng-ht1vx]

I did dad's LB7 truck a bit different. I rotated the engine till the one valve on the engine was fully depressed, and adjusted the other valve on that cylinder. I also adjusted the valves to 0.010". Seems to have quieted the engine down, more power, and it's doing a fair bit better on fuel.
Good video, none the less.

[@bradykolodziejczyk8472]

Most helpful video out there. No more of that annoying diesel clatter.

[@juangamez8428]

Very good info 👍thank you

[@truckmastergarage9944]

Thanks Juan

[@peterk3720]

Great info! I’m presuming this is for the short build? Can’t wait for an on it!

[@user-dv6dx7bs3j]

Once adjusting all valves due to red/yellow procedures and aligning the timing marks should all valves/rockers have .12 or should some have 12 cus the other ones have a little pressure on them?

[@youdecidewitw]

SO, once you adjust the valves, then do the 10 revolutions, if you have to adjust the valves a little more do you do 10 more revs and check again?

[@truckmastergarage9944]

It won’t hurt to do it a second time but once is the preferred

[@kolby3601]

I forgot the dowel for the rocker arms on both sides I put about 400 miles on like that with no issue should I rear it back down and put those in? I know it’s lined up good and torqued correctly..

[@chapekfabrication2975]

It’ll be fine

[@davidparizek6741]

So, the only time you need to adjust the valves is when you pull the head, or is this a maintenance procedure after so many miles 🤷‍♂️, Thanks Ryan, or Josh, wait who made this video 👍

[@JustVince88]

I’m curious too

[@theseaflower]

Valve lash changes by miles. On a high mile truck, it is good to adjust the valves. If you have an LB7, it is a good idea to adjust the valves if you change injectors.

[@truckmastergarage9944]

I made the video Ryan did the talking 😂👍 but you need to do this after you install the heads, but it’s always a good idea to do this if the covers are off

[@scottyach8766]

To perform valve lash adjustment on an LBZ is it required to pull both upper and lower valve covers or can you get it with just the top off

[@killercow-os6bv]

Cylinder 6 valve won't adjust or back of anymore? Any help

[@crazyflashcolt]

Nice video! Do you know if L5P has the same specs? Thanks

[@motomike1197]

So, i just did head gaskets on a lly. Do i mess with anything before i bolt and torque my valve assembly back on, or do i just bolt it back up the way i took it off, and then adjust valves?

[@marshallmclaughlin1214]

I'm also curious the same thing?

[@motomike1197]

@@marshallmclaughlin1214 I've done 3 sets of head gaskets, and replaced head on another. Bolt head on and adjust valves. Pretty straight forward. I did ARP head studs and it came with a sheet showing torque sequence.

[@raulleon3496]

Puedes en español