Mercedes Benz Replace Combination Turn Signal Switch / Toggle / Stalk - C-Class - W203 C320
Вставка
- Опубліковано 29 сер 2024
- I'll show you how I replaced a turn signal switch AKA stalk AKA combination switch AKA toggle. This is the entire signal stalk that is used for turn signal and is also a combination switch for other functions. I replaced the switch because it was broken and would not stay clicked on when trying to turn left. It would turn off or "self-cancel". This can be used as a guide for W203 or 2001-2007 Mercedes C-Class Sedans.
You'll need just a few tools:
- Torx T30
- Torx T10
- Flathead Screwdriver
- Breaker Bar with 10mm hex
Thanks to do it simple, easy and fully explained! This fit with c240 w203 2002 also. Was seeing tons of awful videos trying to take out the steering wheel and, if I follow them, sure will get damage my car electrics. Continue do in it like this! THANKS AGAIN!!!! A real pro!
Good video, thanks it was a great help. Just two things, You should fit the locking piece before you remove the airbag squib. And if you remove the plastic clips over the switches first. You can remove the airbag squib and the steering angle sensor as one piece, which means the copper connections are not exposed.
Excellent addition to a very well done video.
¿cuál es la pieza de bloqueo? ¿pin rojo? ¿dónde comprarlo?
Wow, one of the best instructional video I've ever seen. Thank you.
Agreed. I'm a tech, but I usually run from anything German made, but this is a good one
I followed the instructions although the clips on the air bag were different slightly ,they didn't unclip the same but with a bit of fiddling around got it to work, everything else worked fine and when I connected the battery again everything lit up as before and no fault messages at all ,many thanks and I saved about 300 bucks
Great video. I'm a little nervous about doing this but with your video I think I can do it. I'm a little confused about cutting out the plastic.
I feel the same way great video I wish he had shown a little bit more about cutting the plaster out but it does look dullable.
Thanks for the video! It was easy to follow and just swapped the switch out myself. God Bless 🙏
Great instructions, thank you.
I just did my 2006 CLK in the UK following this guide and it worked although the airbag clips are slightly different to mine.
This is a great video,I use a lot UA-cam instructions,this is clear,concise and very explanatory,good work!
thank you for the compliment, I appreciate it!
Thank you for creating this video. Extremely helpful and it’s easy to follow. Thank you again for taking the time to create this video.
Thank you for sharing. It helped me a lot when I just replaced my switch today.
I'm very happy that this video helped you!
Did this job as per the video , exactly as shown , excellent instructions, many thanks !!!
I'm glad it helped you!
nasze wspaniałe autka , i bezpieczna jazda dla siebie i innych
very nice but do you think i can diy fix the switch without having to replace the whole thing?
Hi after I did this procedur, the srs, esp and bas start to shine, I took it to a work shop but they could put the light out.. they didnt have the oem mercedes software but they clamid that something is wrong with the esp, airbag and brake sensor, any idea what have could happend?
I am experiencing the same problem. The Srs and Esp are illuminating now. I can't figure it out. I even calibrated the steering wheel and it didn't help. Anyone know of a solution?
@@mariagianna9676 maybe something have happend to the clockspring/steering indicator, I took it out and have it back to the center by turning it from side to side and the turn it back to the middle, and then I could have warning lights out
Your video is superb, thank you so much for posting. Ill try it on my 2003 A190
You're very welcome! Thank you for the comment. Hope it works for your A190
Thanks for the video. BTW, what is the name/ reference of the 10 mm hexagonal bit? Didn't you have difficulty to remove the central nut? Please continue with the good job, like that you can help many of us. Regards.
Great video. There are so many different companies selling the part is there one that is recommended that also comes with a locking pin? Thanks again
Very informative video. Unfortunately, you did not share the video for the cut out plastic. I am not sure how much and where to cut.
Thank you. Is there a way to find the part code before I disassemble the unit? I need mine changed and the repair place wants the part code or / if it's a 5 or 6 pin make.
Great video, gonna try it now. My indicator won't jump back after a turn.
You sir are the real mvp much thanks and may god bless you
What could I use instead of the lock pin for the steering angle sensor? Since my package didnt include one.
Unfortunately, it looks absolutely nothing like my C320. At all, but the general concept still helps.
Excellent! Thank you very much.
Thanks, nice clear instructions 👍
Excellent video! Thank you for sharing 😊
Is there a way I can change it from the left to the right side? I swear this thing drives me crazy
Need that specific torx set, long skinny end.
Very helpful thanks for the info...
Excellent
Good clear instructions, thanks for sharing
Hello, I have a Mercedes w203 turn signal that works by itself, without Mayo it turns on and does not turn off.
What I did:
1) pulled out the turn signal switch chips but the turn signals continued to work.
2) I pulled out the chips of all 4 lights and the same thing.
What could be the problem?
Help rozhalusta.
Thanks in advance everyone.
So for those having the same problems with their turn signals lights staying on, it is the TURN SIGNAL SWITCH that is the culprit and not the large N10 relay located at the front end of the windshield inside the engine bay???
I think it's just the signal. Because they still turn on but goes off if you dont hold it with your hand. So it's just the switch that's in the videos that is bad. Nothing in the dash. At least with mine its isnt
So I followed everything you put on here but apparently my steering tilt didn’t work afterwards. I don’t hear the motor run when I press it but my motor works cause it works when I turn off and on my car. Can you help me?
Thank you bro
Thanks.
thanks for this video.
Any tips for if you don’t have a red clip to lock in the steering column?
A paper clip or baling wire will work
@@scottwalker2297 ¿qué función el clip rojo? ¿donde comprarlo?
Thank you :)
Bien
Here's a question for a/one who may have a *SUGGESTION* at least, as two d'ships can't figure this out at all...
The turn signals work, but after "X" amount of time, they *STOP* working. No specific amount of clicks on/off...no certain mileage driven, nothing to associate with the *NOT* working of them, *BUT* if you turn the car off and restart it, they begin working again! No code shows up or gets stored to indicate what the issue is. Others on the web also are searching for help.
VERY GOOD
Thank you!
Bro.
Is the left hand and right hand drive the same replacement...compatible?
Thanks
hi i have a question, i have to have that red plastic key
Where do you get the angle locking clip from?
@bhasins , i think he said it comes with the new replacement part in the box.
Hi just one question, if you do this won't you get any fault message on your display?
Or if you get how can you reset them?
Thanks a lot for the good video!
Great video buddy
Great video, very clear :)
Hi bro.
My signal indicator need replacement..
Is the replacement part same for both left and right hand drive car?
Mine is Right hand drive.
Thanks
I would think so, as long as it’s positioned on the left of the steering wheel.
I just looked up the part for a 2004 W203 C240. The side question did not come up.
@@DerFilmgucker ok..thank you..
Yes,is on the left hand side of the steering
My wiper don't work or the turn signal doesn't either do I have to switch the the turn signal
mafia650 my wipers don’t work either how did you ever fix your problem ???
@@Cappadono I switched the turn signal
What do you mean you switched it ? You bought a another new combination switch ?
Thank you
Top video...thanks
very useful
Hello, where can i find or buy that red thing to lock circle?
YO tampoco se donde comprarlo, ni se lo que hace.
hello friend i have the problem of my 270ml cdi 2004 cranking about 2 seconds and it stops without starting 5 to 7 times without starting i have changed the starter motor and changed the ignition antenna i have checked all the fuse boxes i have found All are going well I have changed the battery and without news but when I connect it with cables with another car working it starts directly. now I do not have to think about any reley that is main! do you know if he has any ??? please help ...
Dear Khalid, I'm not sure what your issue could be. However, an issue with similar symptoms to those you describe occur over here: mbworld.org/forums/c-class-w203/527256-w203-doesn-t-start-does-not-crank-3.html
The driver replaced his ECU to resolve the issue
Map sensörü yada diğer adı ile hava akış metre yi temizlettir kızdırma bujilerini kontürol ettir EGR kelebeğini temizlettir mazot filitresini değiştir
Got to the 10 mm nut which does not budge even using breaker bar. Totally stuck. Any suggestions?
Impact
2:54 what name is that in red???
thanks for share, i will try to repair
Can you Made a video for aux adapter or something helps to listen mp3 on w203 Mercedes 2003 please
Did you disconnect battery first ?
Yes
Hi. my left turn signal swithes on randomly. Do you think its a switch fault?
i'm not 100% sure but maybe the electronics in the turn signal talk have become faulty
Does this method also works on a 1995 s class 320
Where did you get the new turn signal " stick" from? I have a similar issue but its on the right signal
ebay, but you can try other vendors like autohausaz, rmeuro, fcpauto - sometimes even the dealership has cheaper prices
@@ThingsLike Do I need to pay with credit card before getting the packet cuz I dont trust ebay?
@@edward3105 been using ebay for 15 years, never had any serious issues but you can also go to a local car junkyard instead and pick that part yourself. See if you have an auto salvage yard in your area.
My mechanic is scared to do this because he thinks the airbag will go off even with the battery unhooked. Is this fear unfounded or actually something to worry about?
ask him what would trigger the airbag to go off if there is no electrical current running through the system
It will be fine he will just have to disconnect and leave for 15 to 20 mins to allow all copasitors in the vehicle to die down before starting. Once airbag is remove due to the classification it should be put in a strong metal box which is lockable, airbag facing up.
He was worried about the airbag having capacitors or something else in it holding charge; then I guess messing with the connectors setting it off or something. Or he was just lazy and didn't want to do it lol. I did end up doing it myself wit no issues :)
Where to buy this, in uk
God video 👍👍
Can someone tell me how to disarm a mercedes switch log? Please
Merci très utile
I know where is The "Problem" why switch is not standin in his position! don't need buy new one or second hand... you just need open Turn signal box 2.screw and change little black clips right to left , and left to right, and it will be like NEW! ;)
which clips?
what clips?? I have now the problem turn signal not stay in position😪 plss help..
Wow....this looks very difficult 😷😷🙃🙃
Disappointing. Mercedes always so over the top.
Herkesin yorumunu beğenerek konuyu yeniden hirtlatıp hepinizi buraya ben toparladım 😂
Herkesi yorumunu okudum ve herkes benimle aynı fikirde ☺️bende video yu faydalı bulanlar danım ❤
Bizde 2004 model W203 C270 CDI aldık benim araçta da aynı sorun var sinyal kolu tutmuyor 🤷sanırım kıronik bir sorun 😮
nasze wspaniałe autka , i bezpieczna jazda dla siebie i innych
Thank you
Herkesin yorumunu beğenerek konuyu yeniden hirtlatıp hepinizi buraya ben toparladım 😂