10-15mm is chain slack is all that’s needed. Just tightening the axle nut will give you inconsistent chain tension. Put a towel in the chain and roll wheel forward. Will set axle blocks against tension bolts. Tighten axle nut and then roll wheel back and remove towel. Chain tension will always be the same
Please make a video going over proper front and rear suspension settings. I have an E Ride Pro SS 2.0. I am new to the whole scene and feel like my suspension is probably not correct and I cant find any info on how to set it properly. I also want to know in case I have a bad rear shock like you guys had on your 2.0.
Some suggestions : More details on the chain play (50mm up and down when measured in the middle?) and how tight to tighten the centre bolt when done.. 🙏
just got my sting friday, haven’t cut the wire, chain seemed tight when I got it, rode 8-10 miles, noticed it had worn in and would move about an inch and a half up between the sprocket and gearbox. got it tightened up, only thing is I was unsure of wether or not it’s too tight, I saw people saying 10-15mm of play in the middle, seems like it’s close to that but i’m also guessing it may wear in a little more?
@@vladimirp8470 I’m not sure on how to fix it rn, but I’ve emailed Luna n created a ticket asking for advice. I’m gonna go on Reddit later today and see if anyone has had a similar problem.
10-15mm is chain slack is all that’s needed. Just tightening the axle nut will give you inconsistent chain tension. Put a towel in the chain and roll wheel forward. Will set axle blocks against tension bolts. Tighten axle nut and then roll wheel back and remove towel. Chain tension will always be the same
Excellent video thank you very much.
Please make a video going over proper front and rear suspension settings. I have an E Ride Pro SS 2.0. I am new to the whole scene and feel like my suspension is probably not correct and I cant find any info on how to set it properly. I also want to know in case I have a bad rear shock like you guys had on your 2.0.
Will do
Thank you for providing valuable content. Gonna check the tension on my Talarias using your tutorial
Thanks!
Some suggestions : More details on the chain play (50mm up and down when measured in the middle?) and how tight to tighten the centre bolt when done.. 🙏
Because of the flex in the swingarm I have to run mine a bit loose. When hitting big jumps and scrubbing it will bent the sprocket as you land.
Good to know
@@TBElectric yeah, I bent 3 sprockets before I switched to the titanium axle and started running my chain with a bit of play
On a Talaria?
Did this process today and had to repeat like 5 times, what a pita, must be an easier way or better system to adjust it property isn't it?
just got my sting friday, haven’t cut the wire, chain seemed tight when I got it, rode 8-10 miles, noticed it had worn in and would move about an inch and a half up between the sprocket and gearbox.
got it tightened up, only thing is I was unsure of wether or not it’s too tight, I saw people saying 10-15mm of play in the middle, seems like it’s close to that but i’m also guessing it may wear in a little more?
I would like to see the brake pads replaced
Video coming soon
Thank you sir
The brake side for me doesn’t move no matter how much I turn it, i assume it’s broken?
Ya that’s not good
@@TBElectric what do u think I should do?
Same here neither side will move at all
@@vladimirp8470 I emailed luna n created a ticket, if they get back to me I’ll relay the information to u if you’d like.
@@vladimirp8470 I’m not sure on how to fix it rn, but I’ve emailed Luna n created a ticket asking for advice. I’m gonna go on Reddit later today and see if anyone has had a similar problem.
Still don’t understand how you measure the “play” on the chain. Ppl in comments say 10-15mm but how the heck do you measure that?
most people just go on how it looks