Hello and congratulations for the video and also for the beautiful project, How could you do it to drive 220volt lamps? maybe driving some triacs or scr, could you point us in the direction or maybe give us all a nice video? Hello and congratulations again.
@@technoelectronicor show how to trigger 2 of these so that one cycles from green to red and when red it would trigger the other to start cycling. 555 is a very simple timmer I am thinking it should be easy. OR maybe using the 556 chip???
So once I create 2 sets of these how can I trigger (A) when it cycles to red to then trigger (B) to cyle to green for a 4 way traffic signal with 2 channels of output?
Simple but effective and efficient
Thanks 😊
С КР. ДОЛ. НА ЖЕЛ .
I completely agree with you, my friend, the ideal is to make a project as simple as possible. Congratulations, as always.🙂👍🇧🇷
@MarceloSilvaCruz-vm9kh Thanks
Very cool circuit 😉👍👏👏👏👏👏
Thank you! Cheers!
So nice thanks
Most welcome
Creative video,thanks:)
Thanks
Hello and congratulations for the video and also for the beautiful project, How could you do it to drive 220volt lamps? maybe driving some triacs or scr, could you point us in the direction or maybe give us all a nice video? Hello and congratulations again.
You can and you can use relay for 220V lamp.
Gd Job bro keep it up
Plzz upload one video for 4 way traffic 🚦
Ok I will try
@@technoelectronicor show how to trigger 2 of these so that one cycles from green to red and when red it would trigger the other to start cycling. 555 is a very simple timmer I am thinking it should be easy. OR maybe using the 556 chip???
Good
Thanks
Can you do the video of the bread board connections
So once I create 2 sets of these how can I trigger (A) when it cycles to red to then trigger (B) to cyle to green for a 4 way traffic signal with 2 channels of output?
Let me check.
Is this work on Proteus software?
No.
Hi, I tried to make the circuit on the circuit wizard simulator but I noticed that the yellow stays on together with the red. Why? hello and thank you
check circuit diagram
Hola que modificaciones se podrian realizar para hacer variable el tiempo ?
You can change capacitor value.
hi! thanks for the circuit but how can i change the led on duration?
you can change LED duration by increasing capacitor value.
speed capacitor increase blink speed and blink slow ?, any list available ?
check circuit diagram.
Can i do that in pcb?
Yes, you can.
Can you put all the materials you use?
Available in circuit diagram
Only red and green are glowing. Yellow doesnt glow. How can i sort this out?
Have you made this circuit ?
@@technoelectronic yes
Check circuit diagram and verify. Circuit diagram available in end of video
Same problem… I check the circuit but still the yellow did not glow.
Tolong buatin sekema yg 12 volt LED 1 mata besar 1,5 Watt led
ok
Can i get diagram in proteus please
It’s available in video
@@technoelectronic please share link
Can i use the same schematic on multisim ??
Yes
Pahly red on ho phir yellow or phir green
👍
I have seen its circuit diagram its too difficult but it is included in our final , can you please tell where I can find its explanation
Don't think this circuit diagram is difficult, understand the connection and try to make. You will get sauces.
এইটা কি কাজ করে?
এটা হল ট্রাফিক সিগন্যাল লাইট প্রজেক্ট, যা আমরা ক্রস রোডে দেখতে পাই। তোমার উচিত...
@@technoelectronic আরে ওইটা জানি,,, আমি বলছি যে এটা কি আমি বানালে কাজ করবে
হ্যাঁ এটা কাজ করবে (हा यह काम करेगा)
কোন সমস্যা হলে কমেন্ট করুন।
Not working
what is the issue you are facing. follow circuit diagram.
@@technoelectronic i made the exact circuit and not worked, i rechecked 2 times also. So now what can i do to make a this circuit ?
@aayushshah1949 have you checked circuit diagram which is available in video?
@@technoelectronic yes ofcourse sir i checked 2 times. So now what can i do ?
You are not helping your subscriber