Good morning! Do you know the part number (or code) for U1104? I just got one 1100AHX2 that took a lighting strike and the IC's gone... Thanks in advance!
Hello Samuel I have a Routerboard 1100x2AH that has not been in use for a long time. When power cable is connected all the two lights in the ports starts blinking. Please do you have any idea of what might be wrong with it? I can show you a video of it...
I don't drink anymore, Its not like I drank much before but I have gout and the doc said I had to give up red meat and alcohol. I said doc, alcohol is no issue! Congrats on the repair though, Glad I could help! 73
I have seen lots of them used a fuses also. I hope they did not intend on this one being a fuse, Its a 3216 package. The chart I have on my desk only goes up to 2512 and it can hold 6.3A. If I had to take a guess the 3216 will carry 13A or so. If this board would pull 13A you got way more to worry about than this resistor XD the internal PSU is only 3A..
The video is very special Thanks for the effort Can you help me with CCR1009? Sudden problems appear when the device is rebooted, the software deletes. A large number of customers are experiencing the same problem. We have done experiments with the electricity regulator in a number of companies and we have not benefited from anything. Do you expect to have a defect or a control!
It sounds to me like your having a issues with the flash. It is likely if voltage was the issue many other components would have also failed. It is possible to change the flash chip with a SMD station. I do not know if you can flash the new chip in the router. You may need to flash the chip before you install it. If you do not already own the equipment to do this job it is likely more cost effective to just replace the router.
Hi sir is it possible to power up rb1100 directly from a 12v solar powered battery?
Good morning! Do you know the part number (or code) for U1104? I just got one 1100AHX2 that took a lighting strike and the IC's gone... Thanks in advance!
Thank you for the information good work
do you have the schematic rb 1100 ah x2
Hello Samuel
I have a Routerboard 1100x2AH that has not been in use for a long time. When power cable is connected all the two lights in the ports starts blinking.
Please do you have any idea of what might be wrong with it?
I can show you a video of it...
Just resurrected two x2's...I believe I owe you a beer.
73 de W5PKY
I don't drink anymore, Its not like I drank much before but I have gout and the doc said I had to give up red meat and alcohol. I said doc, alcohol is no issue!
Congrats on the repair though, Glad I could help!
73
Esta foi fácil... Muito grato pela dica...
I've seen many zero ohm resistors installed as fuses.
I have seen lots of them used a fuses also. I hope they did not intend on this one being a fuse, Its a 3216 package. The chart I have on my desk only goes up to 2512 and it can hold 6.3A. If I had to take a guess the 3216 will carry 13A or so. If this board would pull 13A you got way more to worry about than this resistor XD the internal PSU is only 3A..
sir rb4011 kaya pa kaya buhayin
The video is very special
Thanks for the effort
Can you help me with CCR1009?
Sudden problems appear when the device is rebooted, the software deletes. A large number of customers are experiencing the same problem.
We have done experiments with the electricity regulator in a number of companies and we have not benefited from anything.
Do you expect to have a defect or a control!
It sounds to me like your having a issues with the flash. It is likely if voltage was the issue many other components would have also failed.
It is possible to change the flash chip with a SMD station. I do not know if you can flash the new chip in the router. You may need to flash the chip before you install it.
If you do not already own the equipment to do this job it is likely more cost effective to just replace the router.
gooddd