I am installing a 9000 BTU Senville split air unit. The unit only draws 6.1amps normally to 8 amps max. I was planning to hook it up to my 15 amp circuit. The circuit will have other appliances on it but I wont be using any of them while this unit is running. The only way I can tap into that circuit is to take a fixture of my porch light which I would remove. The light is controlled by a switch inside which now would control the split air system. I would use the wires from the light fixture that was removed and extend them to my outdoor inverter condensor unit via a wall mounted non fused disconnect which would be mounted outside near the condensor. I have purchased the factory wire back from the outdoor unit to the indoor unit. Do you see any issues with that type of wiring. Your response would be much appreciated.
@@JrElectricSchool Appreciate your hard work in making this Video Bro, In India we have split AC and window AC in residential Buildings in India, I just want to know how the Exchange of Oxygen takes place from outside home to inside the house, since the door and windows are closed of a particular home, and no other ventilation system is there at home
Damn for me that's waaaay too much lol, in my job we connect the indoor until to an MCB and then to outdoor unit then jobs done 😁, we've done it like that for years.
My opinion !!! Too many irrelevant connection. Just make it simple by running the power from the circuit breaker through the DP switch, then run it through the the indoor. The indoor will change the LINE TO SIGNAL which will then run as , Signal, Neutral, Earth for the outdoor....the isolator isnt needed and there is no need for the outdoor to receive power from 2 sides (isolator & indoor) according to your video because if LNE goes into the outdoor, it will nullify the SN coming from the indoor and the compressor will run without rest......check your video its wrong.
I am not AC technician. Recently bought inverter AC and discussed with technician. You are partially correct, as per this video wiring diagram outdoor always runs if it is non-Inverter AC and there are no communication wires in non-inverter ACs, . But in case of Inverter AC, power supply (Phase, Neutral and Earth) should be given to Indoor (to outdoor) or outdoor (to Indoor) and also there will be one or two control/communication lines which runs from indoor to outdoor. These lines actually controls the outdoor unit whether to turn it on/off and also for communication between Indoor and outdoor.
@@balgurimadhukarreddy hi, pls note that as far as split unit is concerned, the connection is same whether inverter or non inverter. I mean power is given to one unit indoor to outdoor OR outdoor to indoor (depending on manufacturer design). The only difference is the inverter technology in it which is another topic entirely as it has to do mostly with AC compressors being swapped for DC. It has absolutely nothing to do with the power supply. Dont get confused pls. However, if this connection in the video is done on 'some' inverter acs, it would cause a lot of damage and owner may have to purchase a new ac.
I have 4 wires comming out from ac indoor and on outdoor i have only 3 sockets one is live second is netural and third is ground so we're to connect that 4 wire ?
Great video..I am trying to figure out if I can run a 18000 BTU mini split on single phase? how big can one go..I've seen 110/220 transformers but I believe they are single phase rather then split..any help is GREATLY appreciated!
Thank you so much, i have learned a lot watching your videos. A little suggestion though, after you finish wiring could you please not end the video immediately so we can fully see the finished work before the video cuts.
Hamare ghar mein 1.5 ton ac ke liye electrical connection karwani hay. To iske liye 10mm Service Wire ( Aluminium ) se connection karein ya fir 4mm Copper Wire se connection karein? Kismein bijli ka bill kam ayega? Sirf AC ke liye alagse MCB jaruri hay kya?
Hi sir im asking about the split unit, whats is the problem of indoor unit, uotdoor unit its working but the indoor unit its not working the blower motor only the ligth green color, close open r on off but outdoor unit still working, maybe posible the capasitor problem, r they have another problems pls sir give your idea,,,, thank you sir,
single phase connection kaise kartehe oski opor ek video he hamara channel par ap jara os video ko dekiye or ham next time solar connection ka video banaye ka koushis koronga Thank you.
For beginner it will not help them to wire the split ac without proper diagram or specific like compressor connection and pcb also with or without contactor.
@@elimarboragay6064 could you please tell how did you got hand and images that matched to power point. Why dont you give one demonstration. Trust me this would be numerous hits if you walkthrough us. Please do its a request.
I am installing a 9000 BTU Senville split air unit. The unit only draws 6.1amps normally to 8 amps max. I was planning to hook it up to my 15 amp circuit. The circuit will have other appliances on it but I wont be using any of them while this unit is running. The only way I can tap into that circuit is to take a fixture of my porch light which I would remove. The light is controlled by a switch inside which now would control the split air system. I would use the wires from the light fixture that was removed and extend them to my outdoor inverter condensor unit via a wall mounted non fused disconnect which would be mounted outside near the condensor. I have purchased the factory wire back from the outdoor unit to the indoor unit. Do you see any issues with that type of wiring. Your response would be much appreciated.
Your work is excellent and easily understand through diagram. I award you 10 stars
Thanks for watching
@@JrElectricSchool
Appreciate your hard work in making this Video Bro, In India we have split AC and window AC in residential Buildings in India, I just want to know how the Exchange of Oxygen takes place from outside home to inside the house, since the door and windows are closed of a particular home, and no other ventilation system is there at home
Best sir
Thiz Iz Way of Perfect Is Made to Your Channel High Buddy and Keep going on👍👍👍...!
Thank you so much
i will try my best
Shandar video sir
Thank you
So where are those components located? Which one is mounted indoors and outdoors? Which of the wires are power and control wires?
Damn for me that's waaaay too much lol, in my job we connect the indoor until to an MCB and then to outdoor unit then jobs done 😁, we've done it like that for years.
Excellent video! What program do you use to make the videos?
Superb vdo bro easily get it in mind thabk you keep it up
Thank you so much 😀
very fantastic for such electrical engineering lessons,well done & thanx alot.😅😄😂
Most welcome!
that is crazy wiring diagram...
why?
Hi may I ask normally 3 core wiring got connect to outdoor compressor ?
Nice bro repair ka bhi upload karo bhai alag alag model ka
Bhai konsa software use karte ho
hamlog animation use karte he
ape jara hamara channel subscribe kejeya neya video dekene kelya. Thank you so much
What if we eliminate the isolator, as well as eliminate the supply from flex out to isolator is it not safe? Explain please, otherwise thanks
Lol
My opinion !!! Too many irrelevant connection. Just make it simple by running the power from the circuit breaker through the DP switch, then run it through the the indoor. The indoor will change the LINE TO SIGNAL which will then run as , Signal, Neutral, Earth for the outdoor....the isolator isnt needed and there is no need for the outdoor to receive power from 2 sides (isolator & indoor) according to your video because if LNE goes into the outdoor, it will nullify the SN coming from the indoor and the compressor will run without rest......check your video its wrong.
Thank`s for your opinion
Thanks I also noticed that
I am not AC technician. Recently bought inverter AC and discussed with technician. You are partially correct, as per this video wiring diagram outdoor always runs if it is non-Inverter AC and there are no communication wires in non-inverter ACs, . But in case of Inverter AC, power supply (Phase, Neutral and Earth) should be given to Indoor (to outdoor) or outdoor (to Indoor) and also there will be one or two control/communication lines which runs from indoor to outdoor. These lines actually controls the outdoor unit whether to turn it on/off and also for communication between Indoor and outdoor.
@@balgurimadhukarreddy hi, pls note that as far as split unit is concerned, the connection is same whether inverter or non inverter. I mean power is given to one unit indoor to outdoor OR outdoor to indoor (depending on manufacturer design). The only difference is the inverter technology in it which is another topic entirely as it has to do mostly with AC compressors being swapped for DC. It has absolutely nothing to do with the power supply. Dont get confused pls. However, if this connection in the video is done on 'some' inverter acs, it would cause a lot of damage and owner may have to purchase a new ac.
The compressor will not run unless it recieve signal from the indoor which turn on the relay. This method is correct
Watching very nice
Thanks for watching
We can directly give it to outdoor without isolator switch ?
yes no problem
I have 4 wires comming out from ac indoor and on outdoor i have only 3 sockets one is live second is netural and third is ground so we're to connect that 4 wire ?
Awesome.....👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍
Thank you so much 😀
Nice teacher
Thank you! 😃
Very good sir
Thanks
hey man where should i put the isolator switch? can i put it outside or inside?
There is no problem you can keep it according to your convenience. Thank you
please subscribe this channel
Great video..I am trying to figure out if I can run a 18000 BTU mini split on single phase? how big can one go..I've seen 110/220 transformers but I believe they are single phase rather then split..any help is GREATLY appreciated!
We are waiting for many more video
we will try to give video very soon.
Thank you.
But all time some need ok no ok crazy making bad actvets grouped playing gues jumped gues
Can a spilt units ac connect with out a isolator switch? On what the 4 connector mean in the indoor units
Thn"q from Singapore
you welcome
Is possible to connect invertor indoor split ac with non invertor outdoor?
Never
Wt is the uses of isolator switch...in u r circuit dgm...plz explaim me
Thank you so much
Very goooooood🌹🌹🌹
Thank you very much
Good work
Thank you so much 😀
Ek room me 5 ac hai aur 2.5 wire me se joint kar sakte hai
ya fir sabhi ke liye alag yani 5 phase mcb se
ha kar sakte he
Thanks
No need for an isolator switch when you already have a dp switch and also the breaker (you can just isolate from there).
Why are MCB and dp switch both?
Lower lighting strike ⚡
Mashallah...Allah apnake hayat dan korun...Amin
Thank you so much, i have learned a lot watching your videos. A little suggestion though, after you finish wiring could you please not end the video immediately so we can fully see the finished work before the video cuts.
your feedback is very important for me
i will try
Thankyou but see all mind good need plying gues not freand bad boyesz some one is dramma making coted
@اللّيث الأبيض thankyou my best all
@@JrElectricSchool nice
Isolater switch what does it do?
for safety
Is possible to make automatic changeover switch by using contacts combined together for electricity an solar system please help
👍👍👍👍👍👍👍👍👍
Supper explanation
Thank you 🙂
Good vdo
Thanks
May i go with this video for wiring of all types AC or there are different ways for different ac?
its wiring for split ac
@@JrElectricSchool what a load of s.... They're not all the same!
Gooood wark bro
Thanks for watching
Nice draing
Thank`s for watching😍
If we want to connect the air conditioning unit Split 3 ton socket 13A at room
How we do this work
you can use 16A socket
My friend your wiring connection is wrong ,,
why?
Is it chart of wiring of air conditioner capacity 1 ton
Sir/madam...Sab electronic appliances mein kaunsi company achhi branded hai bataye plz
nice vedeou
Thank`s for watching this video
please subscribe this channel
Hamare ghar mein 1.5 ton ac ke liye electrical connection karwani hay. To iske liye 10mm Service Wire ( Aluminium ) se connection karein ya fir 4mm Copper Wire se connection karein? Kismein bijli ka bill kam ayega? Sirf AC ke liye alagse MCB jaruri hay kya?
Slemens. Thermal overload relay. No and nc push button. Contacter wiring diagram
Thank you.
You're welcome!
Isolator switch kyu lagate hai sir
How many wire's are in single phase ac switch and are in three phase switch
⚡
what is work of isolater..plz tell my brother
What is Flex out and DP switch
DP SWITCH LOAD AMP?
16Amp
Thank you
What is isolater switch
An isolator is a two-port device that transmits microwave or radio frequency.
please subscribe this channel
Thank you so much
Very nice
Thanks
what does E means?
E Earth
earth
Nice
Thanks for watching
please subscribe this channel
Hi sir im asking about the split unit, whats is the problem of indoor unit, uotdoor unit its working but the indoor unit its not working the blower motor only the ligth green color, close open r on off but outdoor unit still working, maybe posible the capasitor problem, r they have another problems pls sir give your idea,,,, thank you sir,
C wairing ka khasiat keya hai
Thanks for watching
Supper bro
Thanks
Bhai ji ye ducting ac he kya
Please mujhe solar and main single phase connection kaise karte hai jara ek video bana dijiye naa...
single phase connection kaise kartehe oski opor ek video he
hamara channel par ap jara os video ko dekiye
or ham next time solar connection ka video banaye ka koushis koronga
Thank you.
how to draw this type of diagrams in laptop
Thanks you sir
you welcome
For beginner it will not help them to wire the split ac without proper diagram or specific like compressor connection and pcb also with or without contactor.
Iamm all ceacherd all mind rvares need
Good
Thanks
Pleased do it in details, and this is wrong wiring installation.
Sipp 👍👍
Thanks for watching this video
@@JrElectricSchool 🙏
Keep the good work thanks you
Why used insulated switch pls brife me
how to single phase wiring systam
Parabéns.
Bem explicado
sorry i am not understand your language
please tell me Bangla,Hindi,English.
Thank you.
E pila vala arthing he kya bhai
E=Erath
Supper
Thank you
It's from indoor to out door but where is control wire
i will try to make video on your topic.
Thank you.
👌👌👌👌👌👌👌🙏
which software have you used to simulate the diagram
POwer point only
@@elimarboragay6064 could you please tell how did you got hand and images that matched to power point. Why dont you give one demonstration. Trust me this would be numerous hits if you walkthrough us. Please do its a request.
আপনার কথা বুঝতে পারছি ভালো ভাবে, আপনি আমাকে একটা, two way switch কে কিভাবে intermediate switch বানানো যায়, দিলে ভালো হয়।
I will try to make video on your topic.
Thank you
Where is command wire ?
Sir please yeh background music volume kam karo sir bahut destabence hora hai
your feedback is very important for me
i will try to change background music.
Thank you
Out door se indoor me connection hota hai
👍👍👍👍
Thank you👍
he has a power coming from indoor and Yer he has another power coming from isolator.. power for outdoor is only coming from the indoor unit.
কোন সফটওয়্যার দিয়ে ভিডিও বানানো
इंडोर यूनिट कट नहीं होगा कांटीन्यू चलता ही रहेगा। ,,,रागॅ वाइरिग
Hello bro split AC ka man connection outdoor me hota hai .aur kiya jata hai ok .app check kr lena kahi bhi
Abhi Nayaa system aa gaya hai...
Comand cable where indor to outdoor
😍😍😍😍
thank you
❤❤❤
What Name of apps you use for that drawing?
Thanks sir
you welcome
Brother why Earth is heating
Earth is electrical safety.
Thank you.
thank millions thank thank thank
your welcome
Informative.
Thank you so much
please subscribe this channel
Hii
K.jeeva.A c
Se fosse só isso estava muito bom
Maro bes cated
I think this is wrong 🤔
why it seems wrong to you?